Cruise Control Switch Circuit
Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
This circuit sends a signal to the ECM depending on the cruise control switch condition. The battery supplies positive (+) battery voltage to the cruise control switch. Terminal 11 (CCS)*1 or 14 (CCS)*2 of the ECM receives the voltage which varies according to the switch condition.- *1: for 1GR-FE
- *2: for 1KD-FTV, 2TR-FE
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. READ VALUE USING INTELLIGENT TESTER |
Use the Data List to check if the cruise control switch is functioning properly (Click here).
Cruise Control Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Main SW M-CPU
Cruise control switch (Main CPU) / ON or OFF
ON: Cruise control switch on
OFF: Cruise control switch off
-
Cancel Switch
CANCEL switch signal / ON or OFF
ON: CANCEL switch on
OFF: CANCEL switch off
-
SET/COAST Switch
-SET switch signal / ON or OFF
ON: -SET switch on
OFF: -SET switch off
-
RES/ACC Switch
+RES switch signal / ON or OFF
ON: +RES switch on
OFF: +RES switch off
-
- OK:
- On screen, each item changes between ON and OFF according to above chart.
|
|
||||
| OK | ||
| ||
| 2. INSPECT SPIRAL CABLE SUB-ASSEMBLY |
Remove the spiral cable sub-assembly (Click here).
If there are any defects as follows, replace the spiral cable with a new one: scratches, cracks, dents or chips on the connector or spiral cable.

Check the spiral cable.
Set the spiral cable to the center position (Click here).
Rotate the spiral cable 2.5 times clockwise and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable 5 times counterclockwise and measure the resistance according to the value(s) in the table below.
- NOTICE:
- As the spiral cable may break, do not rotate the spiral cable more than the specified amount.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
3 (CCS) - 1 (CCS)
Always
Below 1 Ω
4 (ECC) - 2 (ECC)
Set the spiral cable to the center position and rotate the spiral cable 2.5 times clockwise. Then, while rotating the spiral cable 5 times counterclockwise, measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
3 (CCS) - 1 (CCS)
Always
Below 1 Ω
4 (ECC) - 2 (ECC)
|
|
||||
| OK | |
| 3. INSPECT CRUISE CONTROL SWITCH WIRE |
Disconnect the z7 spiral cable connector.

Disconnect the A switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
z7-3 (CCS) - A-3 (CCS)
Always
Below 2.5 Ω
z7-4 (ECC) - A-1 (ECC)
z7-3 (CCS) - Body ground
Always
1 MΩ or higher
z7-4 (ECC) - Body ground
|
|
||||
| OK | |
| 4. INSPECT CRUISE CONTROL SWITCH |
Remove the cruise control switch (Click here).


Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
3 (CCS) - 1 (ECC)
Cruise control switch on
Below 2.5 Ω
Cruise control switch off
1 MΩ or higher
+RES switch held on
235 to 245 Ω
-SET switch held on
617 to 643 Ω
CANCEL switch held on
1509 to 1571 Ω
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND) |
Disconnect the G40 spiral cable connector.
Disconnect the G56*1, G57*2 or G60*3 ECM connector.
- *1: for 1GR-FE
- *2: for 1KD-FTV
- *3: for 2TR-FE
- *1: for 1GR-FE
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for 1GR-FE Tester Connection
Condition
Specified Condition
G40-1 (CCS) - G56-11 (CCS)
Always
Below 1 Ω
G40-2 (ECC) - Body ground
G40-1 (CCS) - Body ground
Always
10 kΩ or higher
for 2TR-FE Tester Connection
Condition
Specified Condition
G40-1 (CCS) - G60-14 (CCS)
Always
Below 1 Ω
G40-2 (ECC) - Body ground
G40-1 (CCS) - Body ground
Always
10 kΩ or higher
for 1KD-FTV Tester Connection
Condition
Specified Condition
G40-1 (CCS) - G57-14 (CCS)
Always
Below 1 Ω
G40-2 (ECC) - Body ground
G40-1 (CCS) - Body ground
Always
10 kΩ or higher
Result Result
Proceed to
OK (for 1GR-FE)
A
OK (for 2TR-FE)
B
OK (for 1KD-FTV)
C
NG
D
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||
