Rear Wiper does not Operate
Circuit diagnosis · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
When the glass hatch is open, the rear wiper system cuts off the power supply to prevent the rear wiper and rear washer from operating.WIRING DIAGRAM




INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
| 1. READ VALUE USING INTELLIGENT TESTER (GLASS HATCH COURTESY SWITCH) |
Use the Data List to check if the glass hatch opener is functioning properly (Click here).
| Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
| Glass Hatch Courtesy Switch |
Glass hatch courtesy switch signal / ON or OFF |
ON: Glass hatch open OFF: Glass hatch closed |
- |
- OK:
- On tester screen, each item changes between ON and OFF according to above chart.
|
|
||||
| OK | |
| 2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (REAR WIPER MOTOR) |
Using the intelligent tester, perform the Active Test (Click here).
Main Body Tester Display
Test Part
Control Range
Diagnostic Note
Rear Wiper Power Supply
WASHER RR relay operation
ON/OFF
-
- OK:
- Rear wiper motor operates.
|
|
||||
| OK | ||
| ||
| 3. INSPECT WASHER RR RELAY |
Remove the WASHER RR relay from the engine room relay block, junction block.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
3 - 5
Battery voltage is not applied to terminals 1 and 2
10 kΩ or higher
Battery voltage is applied to terminals 1 and 2
Below 1 Ω
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (WASHER RR RELAY - BATTERY) |
Remove the WASHER RR relay from the engine room relay block, junction block.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
WASHER RR relay terminal 2 - Body ground
Ignition switch ON
11 to 14 V
WASHER RR relay terminal 2 - Body ground
Ignition switch off
Below 1 V
WASHER RR relay terminal 5 - Body ground
Always
11 to 14 V
WASHER RR relay terminal 5 - Body ground
Always
Below 1 V
Text in Illustration *a
Front view of wire harness connector
(to WASHER RR Relay)
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - RR WASHER RELAY AND BODY GROUND) |
Remove the WASHER RR relay from the engine room relay block, junction block.
Remove the main body ECU (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G63-20 (RWMR) - WASHER RR relay terminal 1
Always
Below 1 Ω
A-11 (GND1) - Body ground
Always
Below 1 Ω
G63-20 (RWMR) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (WASHER RR RELAY - REAR WIPER MOTOR ASSEMBLY) |
Disconnect the Y1 rear wiper motor connector.
Remove the WASHER RR relay from the engine room relay block, junction block.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
Y1-5 (+B) - WASHER RR relay terminal 3
Always
Below 1 Ω
Y1-5 (+B) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 7. INSPECT REAR WIPER MOTOR ASSEMBLY |
Remove the rear wiper motor (Click here).

Check that the rear wiper motor assembly operates when the battery voltage is applied between the terminals.
- OK:
Tester Connection
Specified Condition
Battery positive (+) → 5 (+B)
Battery negative (-) → 2 (LS)
Battery negative (-) → 3 (E)
Motor operates at low speed (LO)
Battery positive (+) → 5 (+B)
Battery negative (-) → 4 (C1)
Battery negative (-) → 3 (E)
Rear wiper motor operates intermittently
|
|
||||
| OK | |
| 8. CHECK HARNESS AND CONNECTOR (REAR WIPER MOTOR ASSEMBLY - BODY GROUND) |
Disconnect the Y1 rear wiper motor connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
Y1-3 (E) - Body ground
Always
Below 1 Ω
Text in Illustration *a
Front view of wire harness connector
(to Rear Wiper Motor Assembly)
|
|
||||
| OK | |
| 9. INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY |
Remove the windshield wiper switch connector (Click here).


Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for Windshield Wiper Switch LH Side Type:
w/ Rain Sensor Tester Connection
Switch Condition
Specified Condition
16 (C1R) - 9 (EW)
OFF
10 kΩ or higher
18 (+1R) - 9 (EW)
OFF
10 kΩ or higher
16 (C1R) - 9 (EW)
LO
Below 1 Ω
18 (+1R) - 9 (EW)
HI
Below 1 Ω
w/o Rain Sensor Tester Connection
Switch Condition
Specified Condition
B-5 (C1R) - B-2 (EW)
OFF
10 kΩ or higher
B-4 (+1R) - B-2 (EW)
OFF
10 kΩ or higher
B-5 (C1R) - B-2 (EW)
LO
Below 1 Ω
B-4 (+1R) - B-2 (EW)
HI
Below 1 Ω
- for Windshield Wiper Switch RH Side Type:
w/ Rain Sensor Tester Connection
Switch Condition
Specified Condition
12 (C1R) - 1 (EW)
OFF
10 kΩ or higher
10 (+1R) - 1 (EW)
OFF
10 kΩ or higher
12 (C1R) - 1 (EW)
LO
Below 1 Ω
10 (+1R) - 1 (EW)
HI
Below 1 Ω
w/o Rain Sensor Tester Connection
Switch Condition
Specified Condition
B-6 (C1R) - B-2 (EW)
OFF
10 kΩ or higher
B-7 (+1R) - B-2 (EW)
OFF
10 kΩ or higher
B-6 (C1R) - B-2 (EW)
LO
Below 1 Ω
B-7 (+1R) - B-2 (EW)
HI
Below 1 Ω
Text in Illustration *A
for Windshield Wiper Switch LH Side Type
*B
for Windshield Wiper Switch RH Side Type
*C
w/ Rain Sensor
*D
w/o Rain Sensor
|
|
||||
| OK | |
| 10. CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER SWITCH ASSEMBLY - REAR WIPER MOTOR ASSEMBLY AND BODY GROUND) |
for Windshield Wiper Switch LH Side Type:
Disconnect the Y1 rear wiper motor connector.
Disconnect the G120 or G43 windshield wiper switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
w/ Rain Sensor Tester Connection
Condition
Specified Condition
Y1-2 (LS) - G120-18 (+1R)
Always
Below 1 Ω
Y1-4 (C1) - G120-16 (C1R)
Always
Below 1 Ω
G120-9 (EW) - Body ground
Always
Below 1 Ω
Y1-2 (LS) - Body ground
Always
10 kΩ or higher
Y1-4 (C1) - Body ground
Always
10 kΩ or higher
w/o Rain Sensor Tester Connection
Condition
Specified Condition
Y1-2 (LS) - G43-4 (+1R)
Always
Below 1 Ω
Y1-4 (C1) - G43-5 (C1R)
Always
Below 1 Ω
G43-2 (EW) - Body ground
Always
Below 1 Ω
Y1-2 (LS) - Body ground
Always
10 kΩ or higher
Y1-4 (C1) - Body ground
Always
10 kΩ or higher
for Windshield Wiper Switch RH Side Type:
Disconnect the Y1 rear wiper motor connector.
Disconnect the G120 or G43 windshield wiper switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
w/ Rain Sensor Tester Connection
Condition
Specified Condition
Y1-2 (LS) - G120-10 (+1R)
Always
Below 1 Ω
Y1-4 (C1) - G120-12 (C1R)
Always
Below 1 Ω
G120-1 (EW) - Body ground
Always
Below 1 Ω
Y1-2 (LS) - Body ground
Always
10 kΩ or higher
Y1-4 (C1) - Body ground
Always
10 kΩ or higher
w/o Rain Sensor Tester Connection
Condition
Specified Condition
Y1-2 (LS) - G43-7 (+1R)
Always
Below 1 Ω
Y1-4 (C1) - G43-6 (C1R)
Always
Below 1 Ω
G43-2 (EW) - Body ground
Always
Below 1 Ω
Y1-2 (LS) - Body ground
Always
10 kΩ or higher
Y1-4 (C1) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
