Crawl Indicator Light does not Come ON
Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
If the following condition is met, the crawl indicator light turns off and crawl control is stopped.- Crawl control is operated when the vehicle stability control system is malfunctioning, or a vehicle stability control system malfunction occurs during crawl control.
- The transfer is shifted to H4 during crawl control.
- The shift lever is moved to P or N during crawl control.
- The driver side door is opened during crawl control.
When using crawl control continually for a long period of time, if the temperature inside the hydraulic brake booster becomes too high, the crawl indicator light will turn off. After a while, the temperature decreases and crawl control becomes operable.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When replacing the skid control ECU (master cylinder solenoid), perform calibration (Click here).
| 1. CHECK CAN COMMUNICATION LINE |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (for LHD: Click here, for RHD: Click here).
- OK:
- CAN Bus Check indicates no malfunctions in CAN communication.
Result Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
|
|
||||
|
|
||||
| A | |
| 2. CHECK FOR DTC |
Check for DTCs (Click here).
Result Result
Proceed to
DTC is not output
A
DTC is output
B
|
|
||||
| A | |
| 3. READ VALUE USING GTS (CRAWL CONTROL MAIN SWITCH AND DIAL SWITCH SIGNAL) |
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / D-SEAT SW / Data List.
Check the Data List for proper functioning of the crawl on/off switch (center cluster module switch) and crawl speed selector (center cluster module switch).
D-SEAT SW Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Crawl Control Main Switch
Crawl on/off switch/ ON or OFF
ON: Switch on
OFF: Switch off
-
Dial Switch Signal 1
Crawl speed selector/Multi-terrain select road mode selector signal 1/ ON or OFF
Switches between ON and OFF according to the ON/OFF Combination Chart below.
-
Dial Switch Signal 2
Crawl speed selector/Multi-terrain select road mode selector signal 2/ ON or OFF
-
Dial Switch Signal 3
Crawl speed selector/Multi-terrain select road mode selector signal 3/ ON or OFF
-
Operate the crawl speed selector/multi-terrain select road mode selector and check that "Dial Switch Signal 1", "Dial Switch Signal 2" and "Dial Switch Signal 3" in the Data List display ON and OFF according to the chart shown below.

Text in Illustration *1
Center Cluster Module Switch
*2
Crawl On/Off Switch
*3
Multi-terrain Select Switch
*4
Crawl Speed Selector/Multi-terrain Select Road Mode Selector
*a
Low/MUD & SAND
*b
Medium-low/LOOSE ROCK
*c
Medium/MOGUL
*d
Medium-high/ROCK & DIRT
*e
High/ROCK
ON/OFF Combination Chart for "Dial Switch Signal 1", "Dial Switch Signal 2" and "Dial Switch Signal 3" Crawl Speed Selector Position/Multi-terrain Select Road Mode Selector Position
Low/MUD & SAND
Medium-low/LOOSE ROCK
Medium/MOGUL
Medium-high/ROCK & DIRT
High/ROCK
Data List Display
Dial Switch Signal 1
ON
ON
OFF
OFF
OFF
Dial Switch Signal 2
ON
OFF
OFF
OFF
ON
Dial Switch Signal 3
OFF
OFF
OFF
ON
ON
- OK:
- The GTS display changes according to crawl on/off switch (center cluster module switch) and crawl speed selector (center cluster module switch) operation.
|
|
||||
| OK | |
| 4. PERFORM ACTIVE TEST USING GTS (CRAWL CONTROL LIGHT) |
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
ABS/VSC/TRC Tester Display
Test Part
Control Range
Diagnostic Note
Crawl Control Light
Crawl indicator light
Indicator light ON/OFF
Observe combination meter
When performing the Crawl Control Light Active Test, check Crawl Control Light in the Data List (Click here).
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Crawl Control Light
Crawl indicator light/ ON or OFF
ON: Indicator light on
OFF: Indicator light off
-
Result Result
Proceed to
Data List Display
Data List Display when Performing Active Test ON/OFF Operation
ON
Changes between ON and OFF
A
Does not change between ON and OFF (for LHD)
B
Does not change between ON and OFF (for RHD)
C
OFF
Changes between ON and OFF
A
Does not change between ON and OFF (for LHD)
B
Does not change between ON and OFF (for RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 5. CHECK HARNESS AND CONNECTOR (CENTER CLUSTER MODULE SWITCH - DRIVING SUPPORT SWITCH CONTROL ECU) |
Disconnect the G156 center cluster module switch connector.
Disconnect the G162 driving support switch control ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G162-6 (CRWL) - G156-21 (FRB)
Always
Below 1 Ω
G162-4 (MOD1) - G156-17 (ECU)
Always
Below 1 Ω
G162-11 (MOD3) - G156-19 (DN)
Always
Below 1 Ω
G162-2 (MOD2) - G156-18 (UP)
Always
Below 1 Ω
G156-24 (E) - Body ground
Always
Below 1 Ω
G162-6 (CRWL) or G156-21 (FRB) - Body ground
Always
10 kΩ or higher
G162-4 (MOD1) or G156-17 (ECU) - Body ground
Always
10 kΩ or higher
G162-11 (MOD3) or G156-19 (DN) - Body ground
Always
10 kΩ or higher
G162-2 (MOD2) or G156-18 (UP) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 6. INSPECT CENTER CLUSTER MODULE SWITCH |
Remove the center cluster module switch (Click here).
Inspect the crawl on/off switch (center cluster module switch) and crawl speed selector (center cluster module switch) (Click here).
|
|
||||
| OK | ||
| ||
