2013-2015 Land Cruiser Prado · Service Manual Brake

Crawl Indicator Light does not Come ON

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

If the following condition is met, the crawl indicator light turns off and crawl control is stopped.
  1. Crawl control is operated when the vehicle stability control system is malfunctioning, or a vehicle stability control system malfunction occurs during crawl control.
If any of the following conditions are met, the crawl indicator light blinks and crawl control is stopped.
  1. The transfer is shifted to H4 during crawl control.
  2. The shift lever is moved to P or N during crawl control.
  3. The driver side door is opened during crawl control.
When the vehicle is driven at 25 km/h (16 mph) or more during crawl control, control is temporarily stopped and the crawl indicator light blinks.
When using crawl control continually for a long period of time, if the temperature inside the hydraulic brake booster becomes too high, the crawl indicator light will turn off. After a while, the temperature decreases and crawl control becomes operable.

WIRING DIAGRAM

C294551E01

INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU (master cylinder solenoid), perform calibration (Click here).


1. CHECK CAN COMMUNICATION LINE
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (for LHD: Click here, for RHD: Click here).

    OK:
    CAN Bus Check indicates no malfunctions in CAN communication.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A


2. CHECK FOR DTC
  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)
A


3. READ VALUE USING GTS (CRAWL CONTROL MAIN SWITCH AND DIAL SWITCH SIGNAL)
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / D-SEAT SW / Data List.

  1. Check the Data List for proper functioning of the crawl on/off switch (center cluster module switch) and crawl speed selector (center cluster module switch).

    D-SEAT SW 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Crawl Control Main Switch
    Crawl on/off switch/ ON or OFF
    ON: Switch on
    OFF: Switch off
    -
    Dial Switch Signal 1
    Crawl speed selector/Multi-terrain select road mode selector signal 1/ ON or OFF
    Switches between ON and OFF according to the ON/OFF Combination Chart below.
    -
    Dial Switch Signal 2
    Crawl speed selector/Multi-terrain select road mode selector signal 2/ ON or OFF
    -
    Dial Switch Signal 3
    Crawl speed selector/Multi-terrain select road mode selector signal 3/ ON or OFF
    -

    1. C293382E02
      Operate the crawl speed selector/multi-terrain select road mode selector and check that "Dial Switch Signal 1", "Dial Switch Signal 2" and "Dial Switch Signal 3" in the Data List display ON and OFF according to the chart shown below.
      Text in Illustration 
      *1
      Center Cluster Module Switch
      *2
      Crawl On/Off Switch
      *3
      Multi-terrain Select Switch
      *4
      Crawl Speed Selector/Multi-terrain Select Road Mode Selector
      *a
      Low/MUD & SAND
      *b
      Medium-low/LOOSE ROCK
      *c
      Medium/MOGUL
      *d
      Medium-high/ROCK & DIRT
      *e
      High/ROCK
      ON/OFF Combination Chart for "Dial Switch Signal 1", "Dial Switch Signal 2" and "Dial Switch Signal 3" 
      Crawl Speed Selector Position/Multi-terrain Select Road Mode Selector Position
      Low/MUD & SAND
      Medium-low/LOOSE ROCK
      Medium/MOGUL
      Medium-high/ROCK & DIRT
      High/ROCK
      Data List Display
      Dial Switch Signal 1
      ON
      ON
      OFF
      OFF
      OFF
      Dial Switch Signal 2
      ON
      OFF
      OFF
      OFF
      ON
      Dial Switch Signal 3
      OFF
      OFF
      OFF
      ON
      ON

      OK:
      The GTS display changes according to crawl on/off switch (center cluster module switch) and crawl speed selector (center cluster module switch) operation.



NG
Go to step 5
OK


4. PERFORM ACTIVE TEST USING GTS (CRAWL CONTROL LIGHT)
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

    ABS/VSC/TRC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Crawl Control Light
    Crawl indicator light
    Indicator light ON/OFF
    Observe combination meter

  1. When performing the Crawl Control Light Active Test, check Crawl Control Light in the Data List (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Crawl Control Light
    Crawl indicator light/ ON or OFF
    ON: Indicator light on
    OFF: Indicator light off
    -
    Result 
    Result
    Proceed to
    Data List Display
    Data List Display when Performing Active Test ON/OFF Operation
    ON
    Changes between ON and OFF
    A
    Does not change between ON and OFF (for LHD)
    B
    Does not change between ON and OFF (for RHD)
    C
    OFF
    Changes between ON and OFF
    A
    Does not change between ON and OFF (for LHD)
    B
    Does not change between ON and OFF (for RHD)
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

5. CHECK HARNESS AND CONNECTOR (CENTER CLUSTER MODULE SWITCH - DRIVING SUPPORT SWITCH CONTROL ECU)
  1. Disconnect the G156 center cluster module switch connector.

  1. Disconnect the G162 driving support switch control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G162-6 (CRWL) - G156-21 (FRB)
    Always
    Below 1 Ω
    G162-4 (MOD1) - G156-17 (ECU)
    Always
    Below 1 Ω
    G162-11 (MOD3) - G156-19 (DN)
    Always
    Below 1 Ω
    G162-2 (MOD2) - G156-18 (UP)
    Always
    Below 1 Ω
    G156-24 (E) - Body ground
    Always
    Below 1 Ω
    G162-6 (CRWL) or G156-21 (FRB) - Body ground
    Always
    10 kΩ or higher
    G162-4 (MOD1) or G156-17 (ECU) - Body ground
    Always
    10 kΩ or higher
    G162-11 (MOD3) or G156-19 (DN) - Body ground
    Always
    10 kΩ or higher
    G162-2 (MOD2) or G156-18 (UP) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT CENTER CLUSTER MODULE SWITCH
  1. Remove the center cluster module switch (Click here).

  1. Inspect the crawl on/off switch (center cluster module switch) and crawl speed selector (center cluster module switch) (Click here).



NG
REPLACE CENTER CLUSTER MODULE SWITCH (Click here)
OK

REPLACE DRIVING SUPPORT SWITCH CONTROL ECU (Click here)


← Crawl Indicator Light does not Come ON (Aug 2013 – Jul 2014)Multi-terrain Select Indicator Light Remains ON (Aug 2013 – Jul 2014) →