2013-2015 Land Cruiser Prado · Service Manual Brake

C1379 Downhill Assist Control Switch Malfunction (Test Mode DTC)

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

w/ Downhill Assist Control:
DTC C1379 is cleared when the downhill assist control switch sends a downhill assist control operation signal or when test mode ends.
w/ Crawl Control:
DTC C1379 is cleared when the crawl on/off switch (center cluster module switch) and crawl speed selector (center cluster module switch) send a crawl control operation signal or when test mode ends.
DTC Code
DTC Detection Condition
Trouble Area
C1379
Stored only during test mode.
  1. Downhill assist control switch (w/ Downhill Assist Control)
  2. Crawl on/off switch (Center cluster module switch) (w/ Crawl Control)
  3. Crawl speed selector (Center cluster module switch) (w/ Crawl Control)
  4. Harness or connector
  5. Skid control ECU (Master cylinder solenoid)

WIRING DIAGRAM

C214516E10
C293884E01

INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU (master cylinder solenoid), perform calibration (Click here).


1. CONFIRM VEHICLE SPECIFICATIONS
  1. Confirm the vehicle specifications.

    Result 
    Result
    Proceed to
    w/ Downhill Assist Control
    A
    w/ Crawl Control
    B



B
Go to step 6
A


2. READ VALUE USING GTS (DOWNHILL ASSIST CONTROL SW)
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  1. Check the Data List for proper functioning of the downhill assist control switch.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Downhill Assist Control SW
    Downhill assist control switch / ON or OFF
    ON: Downhill assist control on
    OFF: Downhill assist control off
    -

    OK:
    The GTS displays ON or OFF according to downhill assist control switch operation.



NG
Go to step 4
OK


3. CHECK TEST MODE DTC
  1. Perform the downhill assist control switch check in the Test Mode Procedure (Click here).

    OK:
    Test mode DTC C1379 is cleared.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

4. INSPECT DOWNHILL ASSIST CONTROL SWITCH
  1. Remove the downhill assist control switch (Click here).

  1. C215496E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 4
    Not pushed in
    10 kΩ or higher
    Pushed in
    Below 1 Ω

    Text in Illustration  
    *a
    Component without harness connected
    (Downhill Assist Control Switch)



NG
REPLACE DOWNHILL ASSIST CONTROL SWITCH (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - DOWNHILL ASSIST CONTROL SWITCH)
  1. Disconnect the A7 skid control ECU (master cylinder solenoid) connector.

  1. Disconnect the G158 downhill assist control switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A7-44 (HDCS) - G158-4
    Always
    Below 1 Ω
    A7-44 (HDCS) or G158-4 - Body ground
    Always
    10 kΩ or higher
    G158-1 - Body ground
    Always
    Below 1 Ω

    Result 
    Result
    Proceed to
    NG
    A
    OK (for LHD)
    B
    OK (for RHD)
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR

6. CHECK CAN BUS
  1. Check that there are no problems with the CAN communication system (for LHD: Click here, for RHD: Click here).

    Result 
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A


7. READ VALUE USING GTS (CRAWL CONTROL MAIN SWITCH AND DIAL SWITCH SIGNAL)
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / D-SEAT SW / Data List.

  1. Check the Data List for proper functioning of the crawl on/off switch (center cluster module switch) and crawl speed selector (center cluster module switch).

    D-SEAT SW 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Crawl Control Main Switch
    Crawl on/off switch/ ON or OFF
    ON: Switch on
    OFF: Switch off
    -
    Dial Switch Signal 1
    Crawl speed selector/Multi-terrain select road mode selector signal 1/ ON or OFF
    Switches between ON and OFF according to the ON/OFF Combination Chart below.
    -
    Dial Switch Signal 2
    Crawl speed selector/Multi-terrain select road mode selector signal 2/ ON or OFF
    -
    Dial Switch Signal 3
    Crawl speed selector/Multi-terrain select road mode selector signal 3/ ON or OFF
    -

    1. C293382E02
      Operate the crawl speed selector/multi-terrain select road mode selector and check that "Dial Switch Signal 1", "Dial Switch Signal 2" and "Dial Switch Signal 3" in the Data List display ON and OFF according to the chart shown below.
      Text in Illustration 
      *1
      Center Cluster Module Switch
      *2
      Crawl On/Off Switch
      *3
      Multi-terrain Select Switch
      *4
      Crawl Speed Selector/Multi-terrain Select Road Mode Selector
      *a
      Low/MUD & SAND
      *b
      Medium-low/LOOSE ROCK
      *c
      Medium/MOGUL
      *d
      Medium-high/ROCK & DIRT
      *e
      High/ROCK
      ON/OFF Combination Chart for "Dial Switch Signal 1", "Dial Switch Signal 2" and "Dial Switch Signal 3" 
      Crawl Speed Selector Position/Multi-terrain Select Road Mode Selector Position
      Low/MUD & SAND
      Medium-low/LOOSE ROCK
      Medium/MOGUL
      Medium-high/ROCK & DIRT
      High/ROCK
      Data List Display
      Dial Switch Signal 1
      ON
      ON
      OFF
      OFF
      OFF
      Dial Switch Signal 2
      ON
      OFF
      OFF
      OFF
      ON
      Dial Switch Signal 3
      OFF
      OFF
      OFF
      ON
      ON

      OK:
      The GTS display changes according to crawl on/off switch (center cluster module switch) and crawl speed selector (center cluster module switch) operation.



NG
Go to step 9
OK


8. CHECK TEST MODE DTC
  1. Perform the crawl on/off switch (center cluster module switch) and crawl speed selector (center cluster module switch) check in the Test Mode Procedure (Click here).

    OK:
    Test mode DTC C1379 is cleared.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

9. CHECK HARNESS AND CONNECTOR (CENTER CLUSTER MODULE SWITCH - DRIVING SUPPORT SWITCH CONTROL ECU)
  1. Disconnect the G156 center cluster module switch connector.

  1. Disconnect the G162 driving support switch control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G162-6 (CRWL) - G156-21 (FRB)
    Always
    Below 1 Ω
    G162-4 (MOD1) - G156-17 (ECU)
    Always
    Below 1 Ω
    G162-11 (MOD3) - G156-19 (DN)
    Always
    Below 1 Ω
    G162-2 (MOD2) - G156-18 (UP)
    Always
    Below 1 Ω
    G156-24 (E) - Body ground
    Always
    Below 1 Ω
    G162-6 (CRWL) or G156-21 (FRB) - Body ground
    Always
    10 kΩ or higher
    G162-4 (MOD1) or G156-17 (ECU) - Body ground
    Always
    10 kΩ or higher
    G162-11 (MOD3) or G156-19 (DN) - Body ground
    Always
    10 kΩ or higher
    G162-2 (MOD2) or G156-18 (UP) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10. INSPECT CENTER CLUSTER MODULE SWITCH
  1. Remove the center cluster module switch (Click here).

  1. Inspect the crawl on/off switch (center cluster module switch) and crawl speed selector (center cluster module switch) (Click here).



NG
REPLACE CENTER CLUSTER MODULE SWITCH (Click here)
OK

REPLACE DRIVING SUPPORT SWITCH CONTROL ECU (Click here)


← C1379 Downhill Assist Control Switch Malfunction (Test Mode DTC) (Aug 2013 – Jul 2014)C1380 Stop Light Control Relay Malfunction (Aug 2013 – Jul 2014) →