C1379 Downhill Assist Control Switch Malfunction (Test Mode DTC)
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
w/ Downhill Assist Control:DTC C1379 is cleared when the downhill assist control switch sends a downhill assist control operation signal or when test mode ends.
w/ Crawl Control:
DTC C1379 is cleared when the crawl on/off switch (center cluster module switch) and crawl speed selector (center cluster module switch) send a crawl control operation signal or when test mode ends.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1379 |
Stored only during test mode. |
|
WIRING DIAGRAM




INSPECTION PROCEDURE
- NOTICE:
- When replacing the skid control ECU (master cylinder solenoid), perform calibration (Click here).
| 1. CONFIRM VEHICLE SPECIFICATIONS |
Confirm the vehicle specifications.
Result Result
Proceed to
w/ Downhill Assist Control
A
w/ Crawl Control
B
|
|
||||
| A | |
| 2. READ VALUE USING GTS (DOWNHILL ASSIST CONTROL SW) |
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
Check the Data List for proper functioning of the downhill assist control switch.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Downhill Assist Control SW
Downhill assist control switch / ON or OFF
ON: Downhill assist control on
OFF: Downhill assist control off
-
- OK:
- The GTS displays ON or OFF according to downhill assist control switch operation.
|
|
||||
| OK | |
| 3. CHECK TEST MODE DTC |
Perform the downhill assist control switch check in the Test Mode Procedure (Click here).
- OK:
- Test mode DTC C1379 is cleared.
Result Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 4. INSPECT DOWNHILL ASSIST CONTROL SWITCH |
Remove the downhill assist control switch (Click here).
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
1 - 4
Not pushed in
10 kΩ or higher
Pushed in
Below 1 Ω
Text in Illustration *a
Component without harness connected
(Downhill Assist Control Switch)
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - DOWNHILL ASSIST CONTROL SWITCH) |
Disconnect the A7 skid control ECU (master cylinder solenoid) connector.
Disconnect the G158 downhill assist control switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A7-44 (HDCS) - G158-4
Always
Below 1 Ω
A7-44 (HDCS) or G158-4 - Body ground
Always
10 kΩ or higher
G158-1 - Body ground
Always
Below 1 Ω
Result Result
Proceed to
NG
A
OK (for LHD)
B
OK (for RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 6. CHECK CAN BUS |
Check that there are no problems with the CAN communication system (for LHD: Click here, for RHD: Click here).
Result Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
|
|
||||
|
|
||||
| A | |
| 7. READ VALUE USING GTS (CRAWL CONTROL MAIN SWITCH AND DIAL SWITCH SIGNAL) |
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / D-SEAT SW / Data List.
Check the Data List for proper functioning of the crawl on/off switch (center cluster module switch) and crawl speed selector (center cluster module switch).
D-SEAT SW Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Crawl Control Main Switch
Crawl on/off switch/ ON or OFF
ON: Switch on
OFF: Switch off
-
Dial Switch Signal 1
Crawl speed selector/Multi-terrain select road mode selector signal 1/ ON or OFF
Switches between ON and OFF according to the ON/OFF Combination Chart below.
-
Dial Switch Signal 2
Crawl speed selector/Multi-terrain select road mode selector signal 2/ ON or OFF
-
Dial Switch Signal 3
Crawl speed selector/Multi-terrain select road mode selector signal 3/ ON or OFF
-
Operate the crawl speed selector/multi-terrain select road mode selector and check that "Dial Switch Signal 1", "Dial Switch Signal 2" and "Dial Switch Signal 3" in the Data List display ON and OFF according to the chart shown below.

Text in Illustration *1
Center Cluster Module Switch
*2
Crawl On/Off Switch
*3
Multi-terrain Select Switch
*4
Crawl Speed Selector/Multi-terrain Select Road Mode Selector
*a
Low/MUD & SAND
*b
Medium-low/LOOSE ROCK
*c
Medium/MOGUL
*d
Medium-high/ROCK & DIRT
*e
High/ROCK
ON/OFF Combination Chart for "Dial Switch Signal 1", "Dial Switch Signal 2" and "Dial Switch Signal 3" Crawl Speed Selector Position/Multi-terrain Select Road Mode Selector Position
Low/MUD & SAND
Medium-low/LOOSE ROCK
Medium/MOGUL
Medium-high/ROCK & DIRT
High/ROCK
Data List Display
Dial Switch Signal 1
ON
ON
OFF
OFF
OFF
Dial Switch Signal 2
ON
OFF
OFF
OFF
ON
Dial Switch Signal 3
OFF
OFF
OFF
ON
ON
- OK:
- The GTS display changes according to crawl on/off switch (center cluster module switch) and crawl speed selector (center cluster module switch) operation.
|
|
||||
| OK | |
| 8. CHECK TEST MODE DTC |
Perform the crawl on/off switch (center cluster module switch) and crawl speed selector (center cluster module switch) check in the Test Mode Procedure (Click here).
- OK:
- Test mode DTC C1379 is cleared.
Result Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 9. CHECK HARNESS AND CONNECTOR (CENTER CLUSTER MODULE SWITCH - DRIVING SUPPORT SWITCH CONTROL ECU) |
Disconnect the G156 center cluster module switch connector.
Disconnect the G162 driving support switch control ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G162-6 (CRWL) - G156-21 (FRB)
Always
Below 1 Ω
G162-4 (MOD1) - G156-17 (ECU)
Always
Below 1 Ω
G162-11 (MOD3) - G156-19 (DN)
Always
Below 1 Ω
G162-2 (MOD2) - G156-18 (UP)
Always
Below 1 Ω
G156-24 (E) - Body ground
Always
Below 1 Ω
G162-6 (CRWL) or G156-21 (FRB) - Body ground
Always
10 kΩ or higher
G162-4 (MOD1) or G156-17 (ECU) - Body ground
Always
10 kΩ or higher
G162-11 (MOD3) or G156-19 (DN) - Body ground
Always
10 kΩ or higher
G162-2 (MOD2) or G156-18 (UP) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 10. INSPECT CENTER CLUSTER MODULE SWITCH |
Remove the center cluster module switch (Click here).
Inspect the crawl on/off switch (center cluster module switch) and crawl speed selector (center cluster module switch) (Click here).
|
|
||||
| OK | ||
| ||
