2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

INSTALLATION

Removal / installation · Vehicles built from Aug 2013


1. INSTALL AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1)

  1. A223685E01
    Using SST, install the sensor.
    SST
    09224-00010  

    Torque:
    without SST:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }
    with SST:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    Text in Illustration 
    *a
    Fulcrum Length

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). When using a torque wrench with a fulcrum length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).
    2. Make sure SST and the wrench are connected in a straight line.


2. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH

  1. A222094E01
    Install a new gasket to the cylinder head.
    Text in Illustration 
    *1
    Protrusion
    V100135
    Front

    NOTICE:
    Be careful of the installation direction.

  1. Temporarily install the manifold with 6 new nuts.

  1. Tighten the 6 nuts in the sequence shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


    A224820E01
    Text in Illustration 
    *1
    w/ Secondary Air Injection System
    *2
    w/o Secondary Air Injection System

  1. Connect the air fuel ratio sensor connector.


3. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR
  1. Install the heat insulator with the 3 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


4. INSTALL NO. 2 AIR TUBE (w/ Secondary Air Injection System)

  1. A226792E01
    Install 2 new gaskets to the No. 2 air tube.
    Text in Illustration 
    *1
    New Gasket
    *2
    No. 2 Air Tube

  1. Install the No. 2 air tube with the 2 bolts and 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


5. INSTALL MANIFOLD STAY
  1. Install the manifold stay with the 3 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }


6. INSTALL AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)

  1. A223683E01
    Using SST, install the sensor.
    SST
    09224-00010  

    Torque:
    without SST:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }
    with SST:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    Text in Illustration 
    *a
    Fulcrum Length

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). When using a torque wrench with a fulcrum length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).
    2. Make sure SST and the wrench are connected in a straight line.


7. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH

  1. A222095E01
    Install a new gasket to the cylinder head.
    Text in Illustration 
    *1
    Protrusion
    V100135
    Front

    NOTICE:
    Be careful of the installation direction.

  1. Temporarily install the manifold with 6 new nuts.

  1. Tighten the 6 nuts in the sequence shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


    A224819E01
    Text in Illustration 
    *1
    w/ Secondary Air Injection System
    *2
    w/o Secondary Air Injection System

  1. Connect the air fuel ratio sensor connector.


8. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
  1. Install the heat insulator with the 3 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


9. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY (for RHD)
  1. for Manual Tilt and Manual Telescopic Steering Column:
    Connect the No. 2 steering intermediate shaft (Click here).

  1. for Power Tilt and Power Telescopic Steering Column:
    Connect the No. 2 steering intermediate shaft (Click here).


10. INSTALL AIR TUBE (w/ Secondary Air Injection System)

  1. A226791E01
    Install 2 new gaskets to the air tube.
    Text in Illustration 
    *1
    New Gasket
    *2
    Air Tube

  1. Install the air tube with the 2 bolts and 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 in.*lbf }


11. INSTALL NO. 2 MANIFOLD STAY
  1. Install the manifold stay with the 3 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }


12. INSTALL FRONT EXHAUST PIPE ASSEMBLY
  1. Install the front exhaust pipe (Click here).


13. INSTALL AIR CLEANER CASE SUB-ASSEMBLY
  1. Install the air cleaner case with the 3 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. Attach the wire harness clamp.

  1. Install the air cleaner filter element.


14. INSTALL AIR CLEANER CAP AND HOSE

  1. A223697E01
    Install the air cleaner cap and hose.
    Text in Illustration 
    *a
    Top
    *b
    Front
    *c
    RH
    *d
    Align cutout portion of hose with protrusion of throttle
    *e
    Paint Mark

    1. Install the air cleaner cap and hose with the bolt and fasten the 4 hook clamps.

      Torque:
      5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    2. Tighten the clamp.

      Torque:
      5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    3. Attach the 4 clamps and connect the ventilation hose, vacuum hose and mass air flow meter connector.

      HINT:
      The direction of the hose clamp is indicated in the illustration.


15. INSTALL V-BANK COVER

  1. A229926E01
    Attach the 2 V-bank cover hooks to the bracket. Then align the 2 V-bank cover grommets with the 2 pins and press down on the V-bank cover to attach the pins.
    Text in Illustration 
    *1
    Pin
    *2
    Hook


16. INSTALL UPPER RADIATOR SUPPORT SEAL
  1. Install the upper radiator support seal with the 13 clips.


17. INSPECT FOR EXHAUST GAS LEAK
  1. If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.

18. INSTALL FRONT FENDER APRON SEAL LH
  1. w/ KDSS:
    Install the apron seal with the 7 clips.

  1. w/o KDSS:
    Install the apron seal with the 4 clips.


19. INSTALL FRONT FENDER APRON SEAL RH
  1. Install the apron seal with the 5 clips.


20. INSTALL FRONT NO. 1 FENDER APRON TO FRAME SEAL LH
  1. Install the frame seal with the 5 clips.


21. INSTALL FRONT NO. 1 FENDER APRON TO FRAME SEAL RH
  1. Install the frame seal with the 5 clips.

← REMOVAL (from Aug 2013)COMPONENTS (from Aug 2013) →