2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE REAR NO. 1 SEAT ASSEMBLY (w/ Rear No. 1 Seat)
  1. for LH Side:
    Remove the rear No. 1 seat assembly (Click here).

  1. for RH Side:
    Remove the rear No. 1 seat assembly (Click here).


3. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Remove the tonneau cover.


4. REMOVE MAT SET PLATE COVER

B240525E01

HINT:
Use the same procedure for all mat set plate covers.

  1. Using a screwdriver, detach the 2 claws and remove the mat set plate cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective tape


5. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE

B240526
  1. Remove the 5 screws.

  1. Detach the 6 claws and remove the rear floor mat rear support plate.


6. REMOVE QUARTER TRIM COVER HOLE LH

B240533
  1. Detach the 2 claws and 2 guides and remove the quarter trim cover hole.


7. REMOVE REAR FLOOR CARPET ASSEMBLY

B240527
  1. Remove the rear floor carpet.


8. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

B181695

HINT:
Use the same procedure for the other No. 1 luggage compartment trim hook.

  1. Remove the luggage compartment trim hook by turning it clockwise.


9. REMOVE NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)

B240528E01

HINT:
Use the same procedure for the other tonneau cover holder cap.

  1. Using a screwdriver, detach the 2 claws and remove the tonneau cover holder cap.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective tape


10. REMOVE FRONT DECK SIDE TRIM COVER (w/ Tonneau Cover)

B240051E01

HINT:
Use the same procedure for the other front deck side trim cover.

  1. Using a screwdriver, detach the 2 claws and remove the front deck side trim cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective tape


11. REMOVE QUARTER TRIM POCKET TRAY

B240553E01
  1. Put protective tape around the quarter trim pocket tray.

  1. Using a screwdriver, detach the 6 claws and 2 guides, and remove the quarter trim pocket tray.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective tape


12. REMOVE OUTER LAP BELT ANCHOR COVER

B240529

HINT:
Use the same procedure for the other outer lap belt anchor cover.

  1. Detach the 3 claws and remove the outer lap belt anchor cover.


13. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

B240531
  1. Remove the bolt and disconnect the front seat outer belt floor anchor.

  1. B240534
    Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

  1. Remove the 3 bolts and 2 screws.

  1. Detach the 9 claws and 12 clips and remove the deck trim side panel.

    B240536


14. REMOVE REAR QUARTER TRIM PANEL ASSEMBLY LH

B240538
  1. Move the front shoulder belt anchor adjuster to the lowest position.

  1. Remove the bolt.

  1. Detach the 2 clips and 2 guides.

  1. Pass the front seat outer belt floor anchor through the front quarter trim panel and remove the front quarter trim panel.


15. REMOVE DOOR CONTROL RECEIVER

  1. B242777E01
    Disconnect the connector.
    Text in Illustration 
    *A
    w/o Entry and Start System
    *B
    w/ Entry and Start System

  1. Remove the bolt and receiver.

← COMPONENTS (from Aug 2013)REMOVAL (from Aug 2014) →