Main Switch Circuit
Circuit diagnosis · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
for 4 Sensor Type:When the back sonar or clearance sonar switch assembly is turned on, the on signal is input into the ECU.
for 8 Sensor Type
When the driving support switch control ECU receives the clearance sonar on/off switch signal, the ECU sends it to the clearance warning ECU.
WIRING DIAGRAM




INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
| 1. READ VALUE USING GTS |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body / Clearance Sonar / Data List.
According to the display on the GTS, read the Data List.
Clearance Sonar Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Main Switch
TOYOTA parking assist-sensor system (multi-function switch)/OFF or ON
OFF: TOYOTA parking assist-sensor system off
ON: TOYOTA parking assist-sensor system on
-
- OK:
- The display changes as shown above when the TOYOTA parking assist-sensor system is operated.
Result Result
Proceed to
OK
A
NG (for 4 Sensor Type)
B
NG (for 8 Sensor Type)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 2. INSPECT BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY |
Remove the back sonar or clearance sonar switch assembly (Click here).
Inspect the back sonar or clearance sonar switch assembly (Click here).
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY - CLEARANCE WARNING ECU, BATTERY AND BODY GROUND) |
Disconnect the G13 back sonar or clearance sonar switch assembly connector.
Disconnect the I1 clearance warning ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G13-6 (IG) - Body ground
Engine switch on (IG)
11 to 14 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G13-3 (ECU) - I1-12 (CSSW)
Always
Below 1 Ω
G13-7 (IND) - Body ground
Always
Below 1 Ω
G13-3 (ECU) - Body ground
Always
10 kΩ or higher
Result Result
Proceed to
OK (for LHD)
A
OK (for RHD)
B
NG
C
|
|
||||
|
|
||||
| A | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT SWITCH CONTROL ECU - CLEARANCE WARNING ECU) |
Disconnect the G162*1 or G76*2 driving support switch control ECU connector.
- *1: for Automatic Transmission
- *2: for Manual Transmission
- *1: for Automatic Transmission
Disconnect the G154 clearance warning ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for Automatic Transmission Tester Connection
Condition
Specified Condition
G162-9 (SWO1) - G154-12 (CSSW)
Always
Below 1 Ω
G162-9 (SWO1) - Body ground
Always
10 kΩ or higher
for Manual Transmission Tester Connection
Condition
Specified Condition
G76-12 (SWO1) - G154-12 (CSSW)
Always
Below 1 Ω
G76-12 (SWO1) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 5. CHECK DRIVING SUPPORT SWITCH CONTROL ECU |
Replace the driving support switch control ECU with a new or normally functioning one (Click here).
Check the TOYOTA parking assist-sensor system operates normally.
- OK:
- TOYOTA parking assist-sensor system operates normally.
Result Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||
