Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053656 2TR-FE ENGINE CONTROL _0260420 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P2195  Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1)  P2196  Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1)  


DESCRIPTION

The air fuel ratio sensor generates a voltage* that corresponds to the actual air-fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air-fuel ratio. The ECM determines the deviation from the stoichiometric air-fuel ratio and regulates the fuel injection time. If the air fuel ratio sensor malfunctions, the ECM is unable to control the air-fuel ratio accurately.

The air fuel ratio sensor is of the planar type and is integrated with a heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows through the heater to heat the sensor in order to facilitate accurate air-fuel ratio detection. In addition, the sensor and heater portions are the narrow type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, thereby accelerating the sensor activation.

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a Three-Way Catalytic Converter (TWC) is used. For the most efficient use of the Three-Way Catalytic Converter (TWC), the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.

*: The value changes inside the ECM. Since the air fuel ratio sensor is a current output element, the current is converted into a voltage inside the ECM. Any measurements taken at the air fuel ratio sensor or ECM connectors will show a constant voltage.

A306366E26
1.479,2.167 0.99,1.75 0.99,1.75 0.823,1.75 true 1.656,2.094 1.823,1.844 1.823,1.844 1.906,1.844 true 2.938,1.188 3.25,0.135 3.25,0.135 3.406,0.135 true 3.052,1.188 3.292,0.875 3.292,0.875 3.417,0.875 true 2.875,1.667 3.406,1.552 3.406,1.552 2.99,1.667 true 3.042,1.75 3.313,2.083 3.313,2.083 3.406,2.083 true 3.146,1.208 3.406,1.208 false 0.292,1.688 0.979,1.865 0.688,0.177 10 false Element 0.156,2.406 1.208,2.635 1.052,0.229 10 false Exhaust Gas 1.083,2.49 1.417,2.667 0.333,0.177 10 false A 1.802,2.49 2.135,2.667 0.333,0.177 10 false A 1.948,1.792 2.406,2.021 0.458,0.229 10 false Cover 3.448,0.063 4.792,0.5 1.344,0.438 10 false Solid Electrolyte (Zirconia Element) 3.458,0.813 4.125,0.969 0.667,0.156 10 false Alumina 3.448,1.135 4.115,1.292 0.667,0.156 10 false Heater 3.448,1.479 4.677,1.75 1.229,0.271 10 false Platinum Electrode 3.458,2 4.677,2.281 1.219,0.281 10 false Atmospheric Air 2.688,2.354 4.083,2.594 1.396,0.24 10 false A-A Cross Section 5.104,0.063 6.979,0.552 1.875,0.49 10 false ECM Monitored Air Fuel Ratio Sensor Voltage 5.708,2.333 6.688,2.583 0.979,0.25 10 false Air Fuel Ratio

DTC No. DTC Detection Condition Trouble Area
P2195 Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic)

(a) Air fuel ratio sensor voltage more than 3.8 V

(b) Heated oxygen sensor voltage is 0.21 V or more


·

Open or short in air fuel ratio sensor (Sensor 1) circuit

·

Air fuel ratio sensor (Sensor 1)

·

Air fuel ratio sensor (Sensor 1) heater

·

Intake system

·

Exhaust system

·

Fuel line

·

Fuel pressure

·

Fuel injector assembly

·

ECM


While fuel-cut operation performed (during vehicle deceleration), air fuel ratio sensor current is 2.2 mA or more for 3 seconds (2 trip detection logic)
·

Air fuel ratio sensor (Sensor 1)

·

ECM


P2196 Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic)

(a) Air fuel ratio sensor voltage less than 2.8 V

(b) Heated oxygen sensor voltage is below 0.71 V


·

Open or short in air fuel ratio sensor (Sensor 1) circuit

·

Air fuel ratio sensor (Sensor 1)

·

Air fuel ratio sensor (Sensor 1) heater

·

Intake system

·

Exhaust system

·

Fuel line

·

Fuel pressure

·

Fuel injector assembly

·

ECM


While fuel-cut operation performed (during vehicle deceleration), air fuel ratio sensor current is less than 0.7 mA for 3 seconds (2 trip detection logic)
·

Air fuel ratio sensor (Sensor 1)

·

ECM



HINT:
·

When either of these DTCs is stored, check the air fuel ratio sensor output voltage by entering the following menus: Powertrain / Engine and ECT / Data List / All Data / AFS Voltage B1S1.

·

Short-term fuel trim values can also be read using the GTS.

·

The ECM maintains the voltages at the A1A+ and A1A- terminals of the ECM at a constant level. Therefore, the air fuel ratio sensor output voltage cannot be confirmed without using the GTS.

·

If the air fuel ratio sensor is malfunctioning, the ECM stores DTC P2195 or P2196.



MONITOR DESCRIPTION

Sensor voltage detection monitor

Under air-fuel ratio feedback control, If the air fuel ratio sensor output voltage is below 2.8 V (very rich condition) for 5 seconds despite the rear heated oxygen sensor output voltage being below 0.71 V, the ECM stores DTC P2196. Alternatively, if the air fuel ratio sensor output voltage is higher than 3.8 V (very lean condition) for 5 seconds despite the rear heated oxygen sensor output voltage being 0.21 V or higher, DTC P2195 is stored.


Sensor current detection monitor

A rich air-fuel mixture causes a low air fuel ratio sensor current, and a lean air-fuel mixture causes a high air fuel ratio sensor current. Therefore, the sensor output becomes low during acceleration, and it becomes high during deceleration with the throttle valve fully closed. The ECM monitors the air fuel ratio sensor current during fuel-cut and detects any abnormal current values.

If the air fuel ratio sensor output is 2.2 mA or higher for more than 3 seconds of cumulative time, the ECM interprets this as a malfunction in the air fuel ratio sensor and stores DTC P2195 (stuck on high side). If the air fuel ratio sensor output is below 0.7 mA for more than 3 seconds of cumulative time, the ECM stores DTC P2196 (stuck on low side).


A107165E84
2.354,2.25 2.479,1.813 false 4.375,2.25 4.5,1.813 false 5.771,2.25 5.906,1.813 false 0.083,0 2.49,0.24 2.406,0.24 10 false Air Fuel Ratio Sensor Current Monitor: 2.896,0.375 6.313,0.573 3.417,0.198 10 false Cumulative Time "t" = t1 + t2 = 3 seconds or more 0.583,1.073 1.365,1.271 0.781,0.198 10 false Fuel-Cut 1.5,0.865 1.813,1.063 0.313,0.198 10 false ON 1.438,1.156 1.854,1.354 0.417,0.198 10 false OFF 2.354,1.438 3.719,1.635 1.365,0.198 10 false Delay (3 seconds) 4.229,1.438 5.594,1.635 1.365,0.198 10 true Delay (3 seconds) 5.688,1.438 7.052,1.635 1.365,0.198 10 true Delay (3 seconds) 2.323,3.677 3.5,3.854 1.177,0.177 10 true 3 seconds or more 2.323,4.229 4.083,4.427 1.76,0.198 10 false Normal Sensor Output 4.625,4.229 6.292,4.427 1.667,0.198 10 false Abnormal Sensor Output 6.344,4.229 6.813,4.427 0.469,0.198 10 false Time 0.406,2.177 2.052,2.375 1.646,0.198 10 false Sensor Current (mA) 0.406,2.771 2.052,2.969 1.646,0.198 10 false High Side Threshold 0.458,3.417 2.021,3.615 1.563,0.198 10 false Low Side Threshold 4.688,3.698 4.906,3.896 0.219,0.198 10 false t1 6.01,3.698 6.229,3.896 0.219,0.198 10 false t2

MONITOR STRATEGY

Required Sensors/Components (Main) Air fuel ratio sensor
Required Sensors/Components (Related) Heated oxygen sensor
Frequency of Operation Continuous: Sensor voltage detection monitor
Once per driving cycle: Sensor current detection monitor
Duration 5 seconds: Sensor voltage detection monitor
3 seconds: Sensor current detection monitor

TYPICAL ENABLING CONDITIONS

Sensor Voltage Detection Monitor
Time after engine start 30 seconds or more
Fuel system status Closed loop

Sensor Current Detection Monitor
Battery voltage 11 V or higher
Atmospheric pressure 76 kPa (570 mmHg) or higher
Air fuel ratio sensor status Activated
Engine coolant temperature 75°C (167°F) or higher
Continuous time of fuel cut 3 to 10 seconds

TYPICAL MALFUNCTION THRESHOLDS

Sensor Voltage Detection Monitor (Lean Side Malfunction P2195)
Rear heated oxygen sensor voltage 0.21 V or higher
Air fuel ratio sensor voltage Higher than 3.8 V

Sensor Voltage Detection Monitor (Rich Side Malfunction P2196)
Rear heated oxygen sensor voltage Below 0.71 V
Air fuel ratio sensor voltage Below 2.8 V

Sensor Current Detection Monitor (Lean Side Malfunction P2195)
Air fuel ratio sensor current 2.2 mA or higher

Sensor Current Detection Monitor (Rich Side Malfunction P2196)
Air fuel ratio sensor current Below 0.7 mA

CONFIRMATION DRIVING PATTERN

A385740E01
3.969,3.302 4.458,3.448 false 3.99,0.531 3.656,0.531 3.656,0.531 4.906,1.646 true 6.396,0.188 6.875,0.188 6.875,0.188 5.417,1.594 true 4.479,1.469 5.01,1.469 true 5.365,2.24 6.365,2.24 false 2.25,1.073 2.438,1.469 false 0.083,0.229 1.875,0.469 1.792,0.24 10 false ECT: 75°C (167°F) or higher 0.094,0.719 1.083,0.927 0.99,0.208 10 false Vehicle Speed 1.271,0.719 2.917,1.167 1.646,0.448 10 false Between 60 and 100 km/h (37 and 63 mph) 0.708,2.229 1.625,2.427 0.917,0.198 10 false Idling 1.448,2.125 1.906,2.323 0.458,0.198 10 false [A] 3.594,2.125 4.052,2.323 0.458,0.198 10 false [C] 2.708,1.26 3.167,1.458 0.458,0.198 10 false [B] 5.5,1.583 5.958,1.781 0.458,0.198 10 false [E] 4.906,1.26 5.365,1.458 0.458,0.198 10 false [D] 6.073,3.063 6.531,3.26 0.458,0.198 10 false [F] 4.083,0.448 6.323,0.688 2.24,0.24 10 false Accelerator Pedal Depressed 4.083,0.115 6.635,0.323 2.552,0.208 10 false Accelerator Pedal Released (Fuel-cut) 4.604,0.781 5.635,1.021 1.031,0.24 10 false At least 3 times 3.365,1.375 4.458,1.74 1.094,0.365 10 false 60 km/h (37 mph) or more 6.427,1.958 6.99,2.375 0.563,0.417 10 false 10 km/h (6 mph) 6.188,2.479 6.802,2.677 0.615,0.198 10 false Time 5.375,2.698 6.031,3.052 0.656,0.354 10 true 4 seconds or more 4.583,2.698 5.313,3.052 0.729,0.354 10 false 10 seconds or more 4.542,3.375 5.844,3.635 1.302,0.26 10 false Refer to figure below 1.229,2.729 2.01,2.958 0.781,0.229 10 false Warming up 2.469,2.74 3.167,3.104 0.698,0.365 10 false 10 minutes or more

A232909E53
3.635,2.615 3.958,0.865 false 3.365,2.625 2.156,0.688 2.156,0.688 2.281,0.688 false 0.104,0 3.042,0.198 2.938,0.198 10 false Driving Pattern Detail for [C] through [E]: 0.177,0.563 1.948,0.76 1.771,0.198 10 false Reference Engine Speed 2.813,0.156 6.969,0.354 4.156,0.198 10 false Cumulative Detection Period "t" = t1 + t2 + t3 = 3 seconds or more 0.844,1.865 1.615,2.063 0.771,0.198 10 false 2500 rpm 0.844,2.229 1.615,2.427 0.771,0.198 10 false 1000 rpm 1.094,2.417 1.51,2.615 0.417,0.198 10 false Idling 2.188,2.958 2.604,3.156 0.417,0.198 10 false Idling 3.188,3.083 3.969,3.448 0.781,0.365 10 false 4 seconds or more 4.406,3.083 5.188,3.448 0.781,0.365 10 false 4 seconds or more 5.625,3.073 6.406,3.438 0.781,0.365 10 false 4 seconds or more 2.188,2.542 2.406,2.74 0.219,0.198 10 false [C] 2.823,1.198 3.063,1.396 0.24,0.198 10 false [D] 3.458,1.583 3.656,1.781 0.198,0.198 10 false [E] 2.365,0.573 3.552,0.771 1.188,0.198 10 false Delay (3 seconds) 4,0.76 5.438,0.958 1.438,0.198 10 false Detection Period t1 4.813,2.417 4.969,2.615 0.156,0.198 10 false t2 6.031,2.417 6.188,2.615 0.156,0.198 10 false t3 6.479,2.76 6.865,2.958 0.385,0.198 10 false Time

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the tester on.

4.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the tester on.

7.

Start the engine and warm it up until the ECT reaches 75°C (167°F) or higher [A].

8.

On the tester, enter the following menus to check the fuel-cut status: Powertrain / Engine and ECT / Data List / Idle Fuel Cut.

9.

Drive the vehicle at a speed between 60 and 100 km/h (37 and 63 mph) for at least 10 minutes [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

With the shift lever in 2nd gear (for M/T) or 2nd range (for A/T) [C], accelerate the vehicle to 60 km/h (37 mph) or more by depressing the accelerator pedal for at least 10 seconds [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


11.

Soon after performing step [D] above, release the accelerator pedal for at least 4 seconds without depressing the brake pedal in order to execute fuel-cut control [E].

HINT:

Fuel-cut is performed when the following conditions are met:

·

Accelerator pedal is fully released.

·

A/T:

Engine speed is 2000 rpm or more (fuel injection returns at 1500 rpm).

M/T:

Engine speed is 2000 rpm or more (fuel injection returns at 1200 rpm).



12.

Allow the vehicle to decelerate until the vehicle speed decreases to less than 10 km/h (6 mph).

13.

Repeat steps [C] through [E] above at least 3 times in one driving cycle.

14.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [F].

15.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



16.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

17.

Input the DTC: P2195 or P2196.

18.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [F] again.




WIRING DIAGRAM

A355923E04
6.333,1.198 6.792,1.385 0.458,0.188 10 false HT1B 6.115,1.031 6.25,1.229 0.135,0.198 10 false 7 5.896,1.208 6.26,1.385 0.365,0.177 10 false C154 5.896,1.688 6.26,1.865 0.365,0.177 10 false C154 5.896,2.156 6.26,2.333 0.365,0.177 10 false C154 5.896,3.417 6.26,3.594 0.365,0.177 10 false C154 5.896,3.896 6.26,4.073 0.365,0.177 10 false C154 5.896,4.375 6.26,4.552 0.365,0.177 10 false C154 5.896,6.604 6.26,6.781 0.365,0.177 10 false C154 5.896,5.792 6.323,6.042 0.427,0.25 10 false G181 5.896,6.198 6.385,6.385 0.49,0.188 10 false C153 6.156,6.417 6.323,6.563 0.167,0.146 10 false 5 6.135,6 6.302,6.167 0.167,0.167 10 false 3 6.125,5.604 6.26,5.771 0.135,0.167 10 false 6 6.083,4.188 6.302,4.354 0.219,0.167 10 false 34 6.073,3.708 6.271,3.896 0.198,0.188 10 false 26 6.146,3.208 6.313,3.375 0.167,0.167 10 false 6 6.063,1.479 6.281,1.667 0.219,0.188 10 false 27 6.031,1.979 6.229,2.188 0.198,0.208 10 false 35 6.333,1.688 6.76,1.917 0.427,0.229 10 false OX1B 6.333,2.156 6.771,2.365 0.438,0.208 10 false EX1B 4.458,1.094 4.875,1.333 0.417,0.24 10 false HT1B 4.448,1.583 4.865,1.823 0.417,0.24 10 false OX1B 4.625,2.042 4.833,2.25 0.208,0.208 10 false E2 4.927,1.094 5.146,1.313 0.219,0.219 10 false 1 4.948,1.542 5.135,1.792 0.188,0.25 10 false 3 4.938,2.063 5.188,2.271 0.25,0.208 10 false 4 3.833,1.083 4.01,1.26 0.177,0.177 10 false 2 4.01,1.094 4.333,1.26 0.323,0.167 10 false +B 4.427,3.271 4.813,3.438 0.385,0.167 10 false HA1A 4.448,3.781 4.844,3.969 0.396,0.188 10 false A1A+ 4.479,4.26 4.906,4.5 0.427,0.24 10 false A1A- 3.156,1.396 3.958,1.583 0.802,0.188 10 false EFI NO. 2 3.313,1.083 3.479,1.271 0.167,0.188 10 false 1 3.583,1.083 3.74,1.26 0.156,0.177 10 false 2 2.792,1.208 3.104,1.417 0.313,0.208 10 false 1B 2.927,1 3.125,1.198 0.198,0.198 10 false 4 2.802,1.635 3.208,1.854 0.406,0.219 10 false 1B 2.906,1.438 3.073,1.594 0.167,0.156 10 false 2 1.917,1.917 2.24,2.052 0.323,0.135 10 false EFI 0.698,1.354 1.01,1.542 0.313,0.188 10 false EFI 0.688,3.563 0.927,3.74 0.24,0.177 10 false A/F 1.896,4.104 2.438,4.313 0.542,0.208 10 false A/F 1.479,4.292 1.719,4.49 0.24,0.198 10 false 1B 1.771,4.281 1.958,4.5 0.188,0.219 10 false 7 0.99,4.292 1.229,4.5 0.24,0.208 10 false 1B 1.271,4.281 1.427,4.438 0.156,0.156 10 false 3 0.406,4.271 0.646,4.438 0.24,0.167 10 false 1C 0.698,4.271 0.865,4.438 0.167,0.167 10 false 1 2.792,3.427 3.042,3.615 0.25,0.188 10 false 1B 2.885,3.219 3.063,3.406 0.177,0.188 10 false 8 3.917,2.625 4.354,2.906 0.438,0.281 10 false C27 3.927,2.771 5.573,3.094 1.646,0.323 10 false Heated Oxygen Sensor 3.969,4.823 4.365,5.01 0.396,0.188 10 false C56 3.958,4.979 5.344,5.188 1.385,0.208 10 false Air Fuel Ratio Sensor 4.948,3.271 5.083,3.448 0.135,0.177 10 false 1 4.948,3.771 5.135,3.948 0.188,0.177 10 false 3 4.938,4.26 5.115,4.479 0.177,0.219 10 false 4 3.833,3.271 3.979,3.469 0.146,0.198 10 false 2 5.417,2.323 5.583,2.479 0.167,0.156 10 false * 5.406,4.573 5.635,4.76 0.229,0.188 10 false * 1.646,4.51 3.146,4.719 1.5,0.208 10 false NO.1 Integration Relay 0.615,5.313 1.031,5.542 0.417,0.229 10 false P/I-B 0.771,6.188 1.344,6.417 0.573,0.229 10 false Battery 2.958,6.302 3.74,6.479 0.781,0.177 10 false *: Shielded 6.49,7.073 6.927,7.26 0.438,0.188 10 false ECM 6.333,3.417 6.771,3.656 0.438,0.24 10 false HA1A 6.344,3.844 6.75,4.031 0.406,0.188 10 false A1A+ 6.344,4.313 6.74,4.51 0.396,0.198 10 false A1A- 6.333,5.792 6.792,5.979 0.458,0.188 10 false MREL 6.333,6.198 6.667,6.427 0.333,0.229 10 false E1 6.333,6.604 6.688,6.792 0.354,0.188 10 false E04 4.031,3.25 4.24,3.417 0.208,0.167 10 false +B

CAUTION / NOTICE / HINT

HINT:
·

DTC P2A00 may be set, when the air-fuel ratio is stuck rich or lean.

·

A low A/F sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high A/F sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO P2195 OR P2196)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
P2195 or P2196 is output A
P2195 or P2196 and P0136, P0137 or P0138 are output A
P2195 or P2196 and other DTCs are output B

HINT:

If any DTCs relating to the air fuel ratio sensor (DTCs for the air fuel ratio sensor heater or air fuel ratio sensor admittance) are output, troubleshoot those DTCs first.




A

2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST

B

2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST
a.

Has the vehicle run out of fuel in the past?



YES

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)

NO

4.READ VALUE USING GTS (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine and warm it up.


g.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


h.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


i.

Input the DTC: P2195 or P2196.


j.

Check the DTC judgment result.

Result
Result Proceed to
NORMAL (DTC is not output) A
ABNORMAL (DTC P2195 or P2196 is output) B



A

DTC CAUSED BY RUNNING OUT OF FUEL

B

4.READ VALUE USING GTS (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR)
4.READ VALUE USING GTS (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.


f.

Perform the Control the Injection Volume for A/F Sensor operation with the engine idling.


g.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the GTS.

HINT:
·

Change the fuel injection volume within the range of -12.5% to +12.5%.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



GTS Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1
(Air fuel ratio)
+12.5% Rich Below 3.1 V
AFS Voltage B1S1
(Air fuel ratio)
-12.5% Lean Higher than 3.4 V
O2S B1S2
(Heated oxygen)
+12.5% Rich Higher than 0.55 V
O2S B1S2
(Heated oxygen)
-12.5% Lean Below 0.4 V

Result
Status of AFS Voltage B1S1 Status of O2S B1S2 Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition Proceed to
Lean Lean Actual air fuel ratio lean A
Rich Rich Actual air fuel ratio rich A
Lean Lean/Rich Air fuel ratio sensor malfunction B
Rich Lean/Rich Air fuel ratio sensor malfunction B
Lean/Rich Lean/Rich Normal B

Lean: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor output voltage (AFS Voltage) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S) is consistently below 0.4 V.

Rich: During the Control the Injection Volume for A/F Sensor Active Test, the AFS Voltage is consistently below 3.1 V, and the O2S is consistently higher than 0.55 V.

Lean/Rich: During the Control the Injection Volume for A/F Sensor Active Test, the output voltage of the heated oxygen sensor alternates correctly.



A

5.CHECK FOR INTAKE SYSTEM

B

13.REPLACE AIR FUEL RATIO SENSOR
5.CHECK FOR INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

OK:

No leaks in intake system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

6.CHECK FOR EXHAUST GAS LEAK

NG

REPAIR OR REPLACE INTAKE SYSTEM

6.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.


HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

7.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE EXHAUST SYSTEM

7.CHECK FUEL PRESSURE

OK

8.INSPECT FUEL INJECTOR ASSEMBLY

NG

15.CHECK FUEL LINE
8.INSPECT FUEL INJECTOR ASSEMBLY
a.

Check the fuel injector assembly (whether fuel volume is high or low, and whether injector pattern is poor) (See page Engine / Hybrid System>2TR-FE (FUEL)>FUEL INJECTOR>INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

9.REPLACE AIR FUEL RATIO SENSOR

NG

REPLACE FUEL INJECTOR ASSEMBLY

9.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL).

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




NEXT

10.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
10.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine and warm it up.


g.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


h.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


i.

Input the DTC: P2195 or P2196.


j.

Check the DTC judgment result.

Result
Result Proceed to
ABNORMAL (DTC P2195 or P2196 is output) A
NORMAL (DTC is not output) B



A

11.REPLACE ECM

B

END

11.REPLACE ECM

NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine and warm it up.


g.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


h.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


i.

Input the DTC: P2195 or P2196.


j.

Check the DTC judgment result.

Result
GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit





NEXT

END

13.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL).

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




NEXT

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
14.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine and warm it up.


g.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


h.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


i.

Input the DTC: P2195 or P2196.


j.

Check the DTC judgment result.

Result
Result Proceed to
NORMAL (DTC is not output) A
ABNORMAL (DTC P2195 or P2196 is output) B



A

END

B

15.CHECK FUEL LINE
a.

Check the fuel lines for leaks or blockage.

HINT:

Perform "Inspection After Repair" after replacing the fuel pump (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).



Result:
Result Proceed to
NG A
OK
(for 5 door)
B
OK
(for 3 door)
C



A

REPAIR OR REPLACE FUEL LINE

B

C