Home › Engine / Hybrid System › 2TR-FE (FUEL) › FUEL INJECTOR
RM27T0E _51 Engine / Hybrid System _053666 2TR-FE FUEL _0260541 FUEL INJECTOR G

2TR-FE FUEL  FUEL INJECTOR  INSPECTION  


PROCEDURE

Hide 23250 1.INSPECT FUEL INJECTOR ASSEMBLY

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 11.6 to 12.4 Ω


If the result is not as specified, replace the fuel injector assembly.


Hide 23250 2.INSPECT INJECTION VOLUME AND LEAKAGE

a.

Check the injection volume.

CAUTION:

This test involves high-pressure fuel and electricity, therefore, safety precautions should be taken. Perform this test in a safe area and avoid any sparks and flames. Do not smoke.


i.

Discharge the fuel system pressure (See page Engine / Hybrid System>2TR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).


ii.

Remove the fuel hose from the fuel pressure pulsation damper assembly (See page Engine / Hybrid System>2TR-FE (FUEL)>FUEL PRESSURE PULSATION DAMPER>REMOVAL).


iii.

Remove the fuel hose from the fuel filter assembly (See page Engine / Hybrid System>2TR-FE (FUEL)>FUEL FILTER>REPLACEMENT).


iv.

Disconnect the fuel pressure regulator (See page Engine / Hybrid System>2TR-FE (FUEL)>FUEL PRESSURE REGULATOR>REMOVAL).

NOTICE:

Do not disconnect the No. 2 fuel hose.



v.
A273785E06
0.417,0.948 0.552,0.948 0.552,0.948 0.75,1.229 false 2.177,0.281 1,0.281 false 1.833,0.438 1.833,0.281 false 1.208,1.063 1.208,0.281 false 2.156,1.24 2.49,1.24 false 2.156,0.708 2.302,0.708 2.302,0.708 2.302,1.229 false 2.125,0.417 2.323,0.531 2.323,0.531 2.448,0.531 false 2.01,1.646 1.708,1.646 false 2.51,1.542 2.396,1.542 2.396,1.542 2.354,1.781 false 1.542,1.24 1.542,1.031 false 1.688,2.271 2,2.271 false 0.417,2.49 0.323,2.49 0.323,2.49 0.167,2.25 false 2,3.219 2.135,3.219 2.135,3.219 2.344,3.031 false 2.865,0.375 3.073,0.375 false 0.208,0.844 0.417,1.031 0.208,0.188 10 false *a 1.521,1.552 1.719,1.76 0.198,0.208 10 false *f 2.531,1.438 2.76,1.667 0.229,0.229 10 false *g 1.5,2.177 1.76,2.396 0.26,0.219 10 false *2 0.448,2.406 0.677,2.604 0.229,0.198 10 false *1 0.792,0.188 1.031,0.406 0.24,0.219 10 false *b 1.469,1.25 1.677,1.438 0.208,0.188 10 false *e 2.458,0.438 2.635,0.594 0.177,0.156 10 false *d 3.104,0.281 3.323,0.479 0.219,0.198 10 false *c 2.5,1.125 2.75,1.333 0.25,0.208 10 false *b 1.813,3.115 2.031,3.302 0.219,0.188 10 false *3

Assemble SST as shown in the illustration.

SST
09268-31014  (09268-41091, 09268-41110, 09268-41120, 09268-41310, 09268-41500, 09268-41700, 95336-08070)

Text in Illustration
*1 Fuel Pressure Regulator
*2 Fuel Injector Assembly
*3 Fuel Filter Assembly
*a SST (Union)
*b SST (Hose Band)
*c SST (Fuel Tube Connector)
*d SST (3 Way)
*e SST (Hose)
*f SST (Adapter)
*g SST (Clamp)


vi.
A264461E05
1.712,1.141 1.888,1.320 0.176,0.178 10 *a 2.876,1.346 3.050,1.531 0.174,0.185 10 *1 2.327,0.977 2.043,1.235 2.043,1.235 1.909,1.235 false 2.443,1.72 2.73,1.434 2.73,1.434 2.865,1.434 false

Connect SST to the fuel filter assembly.

SST
09268-31014  (09268-41500)

Text in Illustration
*1 Fuel Filter Assembly
*a SST (Fuel Tube Connector)


vii.
A264462E05
1.443,0.376 1.604,0.527 0.162,0.151 10 *1 2.071,0.607 1.775,0.458 1.775,0.458 1.627,0.458 false 3.234,0.791 3.418,0.958 0.184,0.167 10 *a 3.044,0.278 2.748,0.129 2.748,0.129 2.6,0.129 false 3.025,1.01 3.207,1.175 0.183,0.165 10 *b 2.783,0.702 2.891,1.101 2.891,1.101 3.009,1.101 false 2.4,0.033 2.578,0.191 0.178,0.158 10 *c 2.989,0.479 3.096,0.879 3.096,0.879 3.215,0.879 false

Install the fuel pressure regulator to SST (union) with the 2 bolts.

SST
09268-31014  (09268-41091, 09268-41700, 95336-08070)

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

Text in Illustration
*1 Fuel Pressure Regulator
*a SST (Hose Band)
*b SST (Union)
*c SST (Hose)

NOTICE:

Make sure that the O-ring is installed to the pressure regulator.



viii.

Install the O-ring to the fuel injector assembly.


ix.
A264463E05
0.806,1.529 0.991,1.707 0.185,0.178 10 *a 1.47,1.879 1.11,1.627 1.11,1.627 1.006,1.627 false 2.47,0.709 2.657,0.874 0.186,0.165 10 *b 2.192,1.014 2.34,0.792 2.34,0.792 2.458,0.792 false 1.934,0.049 2.139,0.228 0.205,0.179 10 *c 1.657,0.14 1.919,0.14 false 0.911,0.067 1.092,0.229 0.181,0.162 10 *d 1.452,0.301 1.195,0.158 1.195,0.158 1.125,0.158 false 0.911,0.314 1.085,0.490 0.174,0.176 10 *e 1.437,0.548 1.179,0.405 1.179,0.405 1.109,0.405 false

Assemble SST as shown in the illustration.

SST
09268-31014  (09268-41110, 09268-41310, 09268-41700, 95336-08070)

Text in Illustration
*a Vinyl Tube
*b SST (Clamp)
*c SST (Hose)
*d SST (Hose Band)
*e SST (Adaptor)


x.
A264464E06
1.597,1.899 1.796,2.083 0.199,0.184 10 *a 1.32,1.726 1.5,1.988 1.5,1.988 1.589,1.988 false 2.691,0.975 2.906,1.158 0.216,0.183 10 *b 2.489,0.832 2.593,1.06 2.593,1.06 2.679,1.06 false

Pass SST (tie band) through the loop on the handle of SST (clamp) to secure SST (clamp) to SST (adapter).

SST
09268-31014  (09268-41800)

Text in Illustration
*a SST (Tie Band)
*b Lock

NOTICE:
·

As SST (tie band) does not completely prevent SST (clamp) from becoming loose, do not subject the parts to any impacts while using them.

·

Before using SST (tie band), make sure that there is no deterioration, damage or cracks. If there are any abnormalities, replace SST.



HINT:

When removing SST (tie band), disengage the lock.



xi.

Check that SST (clamp) and SST (adapter) cannot be easily separated.


xii.

Put the fuel injector assembly into a graduated cylinder.

CAUTION:

Install a suitable vinyl tube to the fuel injector assembly to contain any gasoline spray.




xiv.
A264465E04
1.745,0.763 1.923,0.973 0.178,0.211 10 *a 1.833,0.27 1.833,0.751 false

Connect SST (EFI inspection wire H) to the fuel injector assembly and the battery for 15 seconds and measure the injection volume with a graduated cylinder. Test each injector 2 or 3 times.

SST
09842-30080  

Standard injection volume:

82 to 99 cm3 (5.0 to 6.0 cu in.) per 15 seconds


Difference between each injector:

17 cm3 (1.0 cu in.) or less


Text in Illustration
*a SST (EFI inspection wire H)
V100135

Connect

NOTICE:
·

Make sure that SST (EFI inspection wire H) is securely connected.

·

Always do the switching at the battery side.



If the injection volume is not as specified, replace the fuel injector assembly.



b.

Check the leakage.

i.

In the condition above, disconnect the tester probes of SST (EFI inspection wire H) from the battery and check the fuel leakage from the fuel injector assembly.

Fuel leakage:

1 drop or less in 25 minutes