Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0031  Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)  P0032  Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)  P0051  Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 2 Sensor 1)  P0052  Oxygen (A/F) Sensor Heater Control Circuit High (Bank 2 Sensor 1)  P101D  A/F Sensor Heater Circuit Performance Bank 1 Sensor 1 Stuck ON  P103D  A/F Sensor Heater Circuit Performance Bank 2 Sensor 1 Stuck ON  


DESCRIPTION

Refer to DTC P2195 (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P2195).

HINT:
·

When any of these DTCs is stored, the ECM enters fail-safe mode. The ECM turns off the air fuel ratio sensor heater in fail-safe mode. The ECM continues operating in fail-safe mode until the engine switch is turned off.

·

Although the DTC titles say heated oxygen sensor, these DTCs relate to the air fuel ratio sensor.

·

Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.

·

The ECM provides a pulse-width modulated control circuit to adjust the current through the heater. The air fuel ratio sensor heater circuit uses a relay on the +B side of the circuit.

A378866E02
0.135,0.146 3.302,0.375 3.167,0.229 10 false Reference (System Diagram of Bank 1 Sensor 1): 0.094,1.073 0.938,1.281 0.844,0.208 10 false from Battery 0.271,2.729 0.854,3.094 0.583,0.365 10 false from EFI Relay 2.24,2.188 2.563,2.365 0.323,0.177 10 false A/F 1.281,0.896 1.604,1.073 0.323,0.177 10 false A/F 3.438,0.969 3.688,1.146 0.25,0.177 10 false +B 3.292,1.635 3.677,1.833 0.385,0.198 10 false A1A- 4.458,0.969 4.896,1.156 0.438,0.188 10 false HA1A 4.469,1.656 4.906,1.844 0.438,0.188 10 false A1A+ 3.844,0.823 4.344,1.01 0.5,0.188 10 false Heater 3.844,1.438 4.344,1.625 0.5,0.188 10 false Sensor 3.719,2.115 4.51,2.313 0.792,0.198 10 false A/F Sensor 5.188,0.969 5.625,1.156 0.438,0.188 10 false HA1A 5.208,1.646 5.646,1.833 0.438,0.188 10 false A1A+ 5.208,2.292 5.594,2.49 0.385,0.198 10 false A1A- 5.896,0.323 6.333,0.51 0.438,0.188 10 false ECM 6.354,1.771 6.875,2.135 0.521,0.365 10 false Duty Control



DTC No. DTC Detection Condition Trouble Area
P0031
P0051
The air fuel ratio sensor heater current is below 0.8 A (1 trip detection logic).
·

Open in air fuel ratio sensor heater circuit

·

Air fuel ratio sensor heater (for bank 1, 2 sensor 1)

·

No. 1 integration relay (A/F)

·

ECM


P0032
P0052
An air fuel ratio sensor heater current failure (1 trip detection logic).
·

Short in air fuel ratio sensor heater circuit

·

Air fuel ratio sensor heater (for bank 1, 2 sensor 1)

·

No. 1 integration relay (A/F)

·

ECM


P101D
P103D
The heater current is higher than a specified value while the heater is not operating (1 trip detection logic).
·

Short in air fuel ratio sensor heater circuit

·

ECM



HINT:
·

Bank 1 refers to the bank that includes the No. 1 cylinder.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



MONITOR DESCRIPTION

The ECM uses information from the air fuel ratio sensor to regulate the air fuel ratio and keep it close to the stoichiometric level. This maximizes the ability of the Three-Way Catalytic Converter (TWC) to purify the exhaust gases.

The air fuel ratio sensor detects oxygen levels in the exhaust gas and transmits the information to the ECM. The inner surface of the sensor element is exposed to the outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum-coated zirconia and includes an integrated heating element.

The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations between the exhaust gas and outside air. The platinum coating amplifies this voltage generation.

The air fuel ratio sensor is more efficient when heated. When the exhaust gas temperature is low, the sensor cannot generate useful voltage signals without supplementary heating. The ECM regulates the supplementary heating using a duty-cycle approach to adjust the average current in the sensor heater element. If the heater current is outside the normal range, the signal transmitted by the air fuel ratio sensor becomes inaccurate, as a result, the ECM is unable to regulate air fuel ratio properly.

When the current in the air fuel ratio sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
a.

Inspect the air fuel ratio sensor (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>INSPECTION).

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

2.CHECK TERMINAL VOLTAGE (+B OF AIR FUEL RATIO SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (+B OF AIR FUEL RATIO SENSOR)
U147483E02
1.865,1.906 2.323,1.615 false 0.198,0.167 0.365,0.365 0.167,0.198 10 false *a 2.396,1.479 2.625,1.698 0.229,0.219 10 false +B 0.823,2.156 1.052,2.354 0.229,0.198 10 false *B 0.396,2.156 0.76,2.354 0.365,0.198 10 false C26 0.813,1.813 1.021,2 0.208,0.188 10 false *A 0.417,1.802 0.792,2 0.375,0.198 10 false C25

a.

Disconnect the air fuel ratio sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C25-2 (+B) - Body ground Engine switch on (IG) 11 to 14 V
C26-2 (+B) - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*A Bank 1
*B Bank 2
*a Front view of wire harness connector
(to Air Fuel Ratio Sensor)


c.

Reconnect the air fuel ratio sensor connector.



OK

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

5.INSPECT NO. 1 INTEGRATION RELAY (A/F)
3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for Automatic Transmission
Tester Connection Condition Specified Condition
C25-1 (HA1A) - C37-17 (HA1A) Always Below 1 Ω
C26-1 (HA2A) - C37-12 (HA2A) Always Below 1 Ω

for Manual Transmission
Tester Connection Condition Specified Condition
C25-1 (HA1A) - C37-17 (HA1A) Always Below 1 Ω
C26-1 (HA2A) - C37-19 (HA2A) Always Below 1 Ω


Standard Resistance (Check for Short):
for Automatic Transmission
Tester Connection Condition Specified Condition
C25-1 (HA1A) or C37-17 (HA1A) - Body ground Always 10 kΩ or higher
C26-1 (HA2A) or C37-12 (HA2A) - Body ground Always 10 kΩ or higher

for Manual Transmission
Tester Connection Condition Specified Condition
C25-1 (HA1A) or C37-17 (HA1A) - Body ground Always 10 kΩ or higher
C26-1 (HA2A) or C37-19 (HA2A) - Body ground Always 10 kΩ or higher



d.

Reconnect the air fuel ratio sensor connector.


e.

Reconnect the ECM connector.



OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Start the engine.


f.

Allow the engine to idle for 1 minute or more.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Read the DTCs.


Result
Result Proceed to
No output A
P0031, P0032, P0051, P0052, P101D or P103D B


A

B

5.INSPECT NO. 1 INTEGRATION RELAY (A/F)
a.

Inspect the air fuel ratio sensor relay (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).



OK

6.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - NO. 1 INTEGRATION RELAY (A/F))

NG

REPLACE NO. 1 INTEGRATION RELAY (A/F)

6.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - NO. 1 INTEGRATION RELAY (A/F))
a.

Disconnect the air fuel ratio sensor connector.


b.

Remove the No. 1 integration relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C25-2 (+B) - 1B-8 Always Below 1 Ω
C26-2 (+B) - 1B-8 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C25-2 (+B) or 1B-8 - Body ground Always 10 kΩ or higher
C26-2 (+B) or 1B-8 - Body ground Always 10 kΩ or higher



d.

Reconnect the air fuel ratio sensor connector.


e.

Reinstall the No. 1 integration relay.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR