Home › Engine / Hybrid System › 5L-E (ENGINE CONTROL) › ECD SYSTEM
RM27T0E _51 Engine / Hybrid System _053658 5L-E ENGINE CONTROL _0260445 ECD SYSTEM C

5L-E ENGINE CONTROL  ECD SYSTEM  P1220  Timer Control Circuit  


DESCRIPTION

The ECM controls the injection timing by actuating the timing control valve. The timing control valve is mounted on the injection or supply pump assembly and controls the internal fuel pressure of the pump through duty control.

The ECM detects the injection advance angle based on the TDC and NE signals.

DTC No. DTC Detection Condition Trouble Area
P1220 During and after engine warm up, actual injection timing is different from target value of ECM calculated for several second.
·

Open or short in timing control valve circuit

·

Timing control valve

·

Fuel filter element sub-assembly (Clogging)

·

Fuel (Freezing, air present)

·

Injection or supply pump assembly (Internal pressure and timing control valve)

·

ECM



WIRING DIAGRAM

A227796E04
2,2.792 3.531,3 1.531,0.208 10 false No. 1 Integration Relay 2.24,2.333 2.729,2.552 0.49,0.219 10 false EFI 1.479,1.427 1.885,1.667 0.406,0.24 10 false EFI 5.604,1.281 6.01,1.521 0.406,0.24 10 false TCV 5.917,4.844 6.323,5.083 0.406,0.24 10 false ECM 5.604,2.094 6.094,2.333 0.49,0.24 10 false MREL 0.604,3.385 1.25,3.625 0.646,0.24 10 false P/I-B 0.76,4.49 1.323,4.729 0.563,0.24 10 false Battery 5.604,3.656 6.01,3.896 0.406,0.24 10 false E1 3.75,1.698 5.125,1.906 1.375,0.208 10 false Timing Control Valve 5.156,1.302 5.646,1.479 0.49,0.177 10 false C161 5.156,2.094 5.646,2.26 0.49,0.167 10 false G183 5.156,3.667 5.646,3.844 0.49,0.177 10 false C161 5.26,1.094 5.51,1.271 0.25,0.177 10 false 11 5.271,1.896 5.521,2.063 0.25,0.167 10 false 10 5.281,3.469 5.531,3.646 0.25,0.177 10 false 5 3.75,1.531 4.24,1.708 0.49,0.177 10 false C108 3.948,1.177 4.198,1.344 0.25,0.167 10 false 1 4.688,1.177 4.938,1.344 0.25,0.167 10 false 2 3,2.094 3.208,2.26 0.208,0.167 10 false 1B 3.042,1.896 3.219,2.063 0.177,0.167 10 false 2 3,1.313 3.208,1.479 0.208,0.167 10 false 1B 3.052,1.104 3.229,1.271 0.177,0.167 10 false 4 0.958,1.302 1.167,1.469 0.208,0.167 10 false 1C 1.01,1.104 1.188,1.271 0.177,0.167 10 false 1 1.49,2.542 1.698,2.708 0.208,0.167 10 false 1B 1.229,2.531 1.406,2.698 0.177,0.167 10 false 3

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT TIMING CONTROL VALVE
a.

Inspect the timer control valve (See page Engine / Hybrid System>5L-E (FUEL)>FUEL INJECTION PUMP>INSPECTION).



OK

2.INSPECT TIMING CONTROL VALVE (POWER SOURCE)

NG

REPLACE TIMING CONTROL VALVE

2.INSPECT TIMING CONTROL VALVE (POWER SOURCE)
a.
U169087E02
0.083,0.063 0.281,0.229 0.198,0.167 10 false *a 0.573,0.958 0.938,1.115 0.365,0.156 10 false C108

Disconnect the timing control valve connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C108-1 - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Timing Control Valve)



OK

3.CHECK HARNESS AND CONNECTOR (TIMING CONTROL VALVE - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TIMING CONTROL VALVE - NO. 1 INTEGRATION RELAY)

3.CHECK HARNESS AND CONNECTOR (TIMING CONTROL VALVE - ECM)
a.

Disconnect the timing control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C108-2 - C161-11 (TCV) Always Below 1 Ω
C108-2 or C161-11 (TCV) - Body ground Always 10 kΩ or higher




OK

4.CHECK FUEL FILTER ELEMENT SUB-ASSEMBLY

NG

END

4.CHECK FUEL FILTER ELEMENT SUB-ASSEMBLY
a.

Check the fuel filter element sub-assembly.



OK

5.CHECK FUEL LEAK

NG

REPLACE FUEL FILTER ELEMENT SUB-ASSEMBLY

5.CHECK FUEL LEAK
a.

Visually check the injection or supply pump assembly, each injector and fuel line for fuel leaks (See page Engine / Hybrid System>5L-E (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).

OK:

No leakage




OK

6.REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY

NG

REPAIR FUEL LEAK

6.REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY
a.

Replace the injection or supply pump assembly (See page Engine / Hybrid System>5L-E (FUEL)>FUEL INJECTION PUMP>REMOVAL).



NEXT

7.CHECK READ OUTPUT DTC (DTC P1220 IS OUTPUT AGAIN)
7.CHECK READ OUTPUT DTC (DTC P1220 IS OUTPUT AGAIN)

b.

Start the engine.


c.

Idle the engine for 20 sec. or more.


d.

Read the DTC (See page Engine / Hybrid System>5L-E (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).

Result:
Display (DTC output) Proceed to
DTC P1220 is output again A
No DTC output B




A

B

END