The EGR valve position sensor is mounted on the EGR valve and is used for detecting the lift amount of the valve. The lift amount detected by the sensor is provided to the ECM as feedback. The ECM then regulates the lift amount of the valve in accordance with engine running conditions.
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Ignition switch ON for 5 seconds | EGR valve position sensor output voltage is below 0.1 V for more than 5 seconds (1 trip detection logic). | ·
Open or short in EGR valve position sensor circuit ·
EGR valve position sensor ·
ECM |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Ignition switch ON for 5 seconds | EGR valve position sensor output voltage is more than 4.9 V for higher than 5 seconds (1 trip detection logic). | ·
Open or short in EGR valve position sensor circuit ·
EGR valve position sensor ·
ECM |
When the output voltage of the EGR valve position sensor deviates from the normal operating range of 0.1 to 4.9 V for more than 5 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Disconnect the EGR valve position sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C86-1 (VC) - C86-2 (E2) | Ignition switch ON | 4.5 to 5.5 V |
| *a | Front view of wire harness connector
(to EGR valve position sensor) |
Reconnect the electric vacuum regulating valve assembly connector.
OK
NG
Inspect the EGR valve position sensor (See page Engine / Hybrid System>1KD-FTV (EMISSION CONTROL)>EGR VALVE>INSPECTION).
OK
NG
Disconnect the EGR valve position sensor connector.
Disconnect the ECM connectors.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 86-1 (VC) - C91-13 (VCEG) | Always | Below 1 Ω |
| C86-3 (EGLS) - C91-4 (EGLS) | Always | Below 1 Ω |
| C86-2 (E2) - C91-14 (EEGL) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 86-1 (VC) or C91-13 (VCEG) - Body ground | Always | 10 kΩ or higher |
| C86-3 (EGLS) or C91-4 (EGLS) - Body ground | Always | 10 kΩ or higher |
Reconnect the electric vacuum regulating valve assembly connector.
Reconnect the ECM connector.
OK
NG
Replace the ECM (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Replace the electric EGR control valve assembly (See page Engine / Hybrid System>1KD-FTV (EMISSION CONTROL)>EGR VALVE>REMOVAL).
NEXT
Repair or replace the harness or connector.
NEXT
Connect the intelligent tester to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch to ON for 5 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
NEXT