Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260458 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P0088  Fuel Rail / System Pressure - Too High  


DESCRIPTION

P0088
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
After idling for 60 seconds, quickly increase engine speed to 2500 rpm repeatedly for 30 seconds The fuel pressure of the common rail exceeds 200000 kPa (2039 kgf/cm2, 29000 psi) (1 trip detection logic).
·

Suction control valve

·

Pressure discharge valve (common rail)

·

Open or short in suction control valve circuit

·

Fuel pressure sensor (common rail)

·

ECM



Related Data List
DTC No. Data List
P0088
·

Fuel Press

·

Target Common Rail Pressure

·

Target Pump SCV Current



HINT:
·

For more information on the fuel supply pump assembly (suction control valve) and common rail system, refer to System Description (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>SYSTEM DESCRIPTION).

·

When DTC P0088 is stored, check the internal fuel pressure of the common rail by entering the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.

Reference
Engine Speed Fuel Press
Idling Approximately 30000 to 40000 kPa
3000 rpm (No engine load) Approximately 45000 to 75000 kPa

·

Check "Fuel Press", "Target Common Rail Pressure" and "Target Pump SCV Current" in the freeze frame data.



MONITOR DESCRIPTION

P0088 (Internal fuel pressure too high):

The ECM stores this DTC if the fuel pressure inside the common rail is higher than 200000 kPa (2039 kgf/cm2, 29000 psi). This DTC indicates that: 1) the suction control valve may be stuck open, or 2) there may be a short in the suction control valve circuit.

If this DTC is stored, the ECM enters fail-safe mode and limits the engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.


WIRING DIAGRAM

A205135E84
2.073,1.406 2.271,1.583 0.198,0.177 10 false 2 5.396,0.74 5.604,0.917 0.208,0.177 10 false 23 5.406,1.406 5.604,1.583 0.198,0.177 10 false 12 5.708,1.281 6.125,1.458 0.417,0.177 10 false PCV- 5.99,2.042 6.385,2.219 0.396,0.177 10 false ECM 5.708,0.625 6.125,0.802 0.417,0.177 10 false PCV+ 2.073,0.74 2.271,0.917 0.198,0.177 10 false 1 0.646,2.031 2.042,2.219 1.396,0.188 10 false Suction Control Valve 5.99,1.865 6.313,2.021 0.323,0.156 10 false C92 0.667,1.854 0.969,2.031 0.302,0.177 10 false C71

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0088)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.


d.

Read Current DTCs.

Result
Result Proceed to
P0088 A
P0088 and "P0190, P0192 and/or P0193" B

HINT:

When there is an open circuit in the fuel pressure sensor circuit, the fuel pressure sensor outputs the maximum value. Therefore, P0088 may be stored together with DTCs which indicate common rail fuel pressure sensor circuit malfunctions.




A

2.CHECK FREEZE FRAME DATA (FUEL PRESS)

B

GO TO FUEL RAIL PRESSURE SENSOR CIRCUIT

2.CHECK FREEZE FRAME DATA (FUEL PRESS)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.


d.

Record the stored DTCs and freeze frame data.

Result
Result Proceed to
Value of Fuel Press is shifting towards 160000 kPa or higher in 3rd and 4th set of freeze frame data B
Except above A



A

3.INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE)

B

4.REPLACE SUCTION CONTROL VALVE
3.INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE)
a.
U169104E02
1.521,0.875 1.76,1.656 true 1.417,0.313 1.719,0.49 0.302,0.177 10 false C90 0.073,0.063 0.292,0.25 0.219,0.188 10 false *a 1.458,1.688 2.302,1.938 0.844,0.25 10 false 16 (PCR1)

Connect the positive (+) probe of an oscilloscope to the fuel pressure sensor input terminal of the ECM connector and the negative (-) probe to the body ground.


b.

Turn the ignition switch to ON.


c.

Check for any noise in the waveform when vibration is applied to the wire harness and connectors between the fuel pressure sensor and ECM.

A192850E31
0.885,2.5 0.542,2.844 0.542,2.844 0.542,2.938 false 2.229,1.708 2.74,2.865 2.74,2.865 2.74,2.958 false 0.083,0.063 2.063,0.271 1.979,0.208 10 false Vibration Method (Reference) 0.24,2.958 1.125,3.198 0.885,0.24 10 false Engine Wire 2.104,2.99 3.615,3.406 1.51,0.417 10 false Common Rail Assembly (Fuel Pressure Sensor) 3.656,1.146 4.521,1.385 0.865,0.24 10 false Wire to Wire 1.469,0.479 2.031,0.708 0.563,0.229 10 false Engine 5.74,1.167 6.188,1.417 0.448,0.25 10 false ECM

A192849E35
2.115,1.865 3.073,0.677 3.073,0.677 3.167,0.677 false 3.104,1.865 3.74,1.5 3.74,1.5 3.823,1.5 false 3.865,1.427 5.906,1.865 2.042,0.438 10 false Sensor Output Signal with Noise (Problem with Wire Connection) 3.229,0.594 5.448,1.031 2.219,0.438 10 false Sensor Output Signal without Noise (Normal Wire Connection) 1.573,0.219 2.313,0.406 0.74,0.188 10 false Example: 4.385,2.49 6.656,2.688 2.271,0.198 10 false Tester Range (Reference): 4.385,2.844 6.813,3.042 2.427,0.198 10 false 200 mV/DIV., 500 μsec./DIV. or less

Standard Voltage:
Tester Connection Condition Specified Condition
C90-16 (PCR1) - Body ground Vibration is applied to the wire harness and connectors No noise in the waveform


Text in Illustration
*a Component with harness connected
(ECM)

Result
Result Proceed to
MIL comes on or noise present in the waveform B
Except above A



A

4.REPLACE SUCTION CONTROL VALVE

B

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE SUCTION CONTROL VALVE
a.

Replace the suction control valve (See page Engine / Hybrid System>1KD-FTV (FUEL)>SUCTION CONTROL VALVE>REMOVAL).

HINT:

Before replacing the suction control valve, check that the wire harness between the suction control valve and ECM is not shorted to ground.

When there is a malfunction in the wire harness, Target Pump SCV Current is outside the range of 923 to 1123 mA when idling, and outside the range of 1013 to 1212 mA when the engine is running at 2500 rpm without load.

If there are no problems with the engine condition during idling, it is not necessary to perform the above wire harness inspection.

When the wire harness between the suction control valve and ECM is not shorted to ground, it can be assumed that DTC P0088 was stored due to a malfunction in the operation of the suction control valve. Therefore, it is necessary to replace the suction control valve.




NEXT

5.BLEED AIR FROM FUEL SYSTEM
5.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).



NEXT

6.PERFORM FUEL SUPPLY PUMP INITIALIZATION
6.PERFORM FUEL SUPPLY PUMP INITIALIZATION
a.

Perform fuel supply pump initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON and start the engine.


e.

After idling for 60 seconds, increase the engine speed from idling to 2500 rpm repeatedly for 30 seconds.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


ii.

Input DTC P0088.


iii.

Check the DTC judgment result.

Result
Tester Display Result Proceed to
Pending DTC P0088 is output A
All Readiness NORMAL B
ABNORMAL A

HINT:

If STATUS is INCOMPLETE or N/A, race the engine to 2500 rpm repeatedly for 30 seconds and increase the idling time.





A

8.REPLACE ECM

B

END

8.REPLACE ECM

NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

10.INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE)
10.INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE)
a.
U169104E02
1.521,0.875 1.76,1.656 true 1.417,0.313 1.719,0.49 0.302,0.177 10 false C90 0.073,0.063 0.292,0.25 0.219,0.188 10 false *a 1.458,1.688 2.302,1.938 0.844,0.25 10 false 16 (PCR1)

Connect the positive (+) probe of an oscilloscope to the fuel pressure sensor input terminal of the ECM connector and the negative (-) probe to the body ground.


b.

Turn the ignition switch to ON.


c.

Check for any noise in the waveform when vibration is applied to the wire harness and connectors between the fuel pressure sensor and ECM.

Standard Voltage:
Tester Connection Condition Specified Condition
C90-16 (PCR1) - Body ground Vibration is applied to the wire harness and connectors No noise in the waveform


Text in Illustration
*a Component with harness connected
(ECM)

Result
Result Proceed to
MIL comes on or noise present in the waveform A
Except above B



A

11.REPLACE COMMON RAIL ASSEMBLY

B

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPLACE COMMON RAIL ASSEMBLY
a.

Replace the common rail (See page Engine / Hybrid System>1KD-FTV (FUEL)>COMMON RAIL>REMOVAL).



NEXT

12.BLEED AIR FROM FUEL SYSTEM
12.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON and start the engine.


e.

After idling for 60 seconds, increase the engine speed from idling to 2500 rpm repeatedly for 30 seconds.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


ii.

Input DTC P0088.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, race the engine to 2500 rpm repeatedly for 30 seconds and increase the idling time.




NEXT

END