| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Idling for 1 second | Even though the CPU (command area inside the ECU) is outputting the suction control valve operation duty, the output monitor signal is absent for 0.5 seconds (1 trip detection logic). | ·
Open or short in suction control valve circuit ·
Suction control valve ·
ECM |
| DTC No. | Data List |
|---|---|
| P0627 | Fuel Press
Target Common Rail Pressure |
For more information on the fuel supply pump assembly (suction control valve) and common rail system, refer to System Description (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>SYSTEM DESCRIPTION).
When DTC P0627 is stored, check the internal fuel pressure of the common rail by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / Fuel Press.
Under a stable operating condition such as idling, Fuel Press is within 5000 kPa of Target Common Rail Pressure.
Refer to DTC P0088 (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>P0088).
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Inspect the suction control valve (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL SUPPLY PUMP>INSPECTION).
OK
NG
Disconnect the suction control valve connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C71-1 - C92-23 (PCV+) | Always | Below 1 Ω |
| C71-2 - C92-12 (PCV-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C71-1 or C92-23 (PCV+) - Body ground | Always | 10 kΩ or higher |
| C71-2 or C92-12 (PCV-) - Body ground | Always | 10 kΩ or higher |
Reconnect the suction control valve connector.
Reconnect the ECM connector.
OK
NG
Connect the intelligent tester to the DLC3
Turn the ignition switch to ON and turn the tester on.
Clear the DTCs (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Start the engine and idle it for 1 second or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| No DTC is output | A |
| P0627 is output | B |
A
B
Replace the suction control valve (See page Engine / Hybrid System>1KD-FTV (FUEL)>SUCTION CONTROL VALVE>REMOVAL).
NEXT
Bleed the air from the fuel system (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).
NEXT
Perform fuel supply pump initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
NEXT
Replace the ECM (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Repair or replace the harness or connector.
NEXT
Connect the intelligent tester to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off for 30 seconds or more.
Start the engine and idle it for 1 second or more.
Confirm that the DTC is not output again.
NEXT