Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260458 ECD SYSTEM J

1KD-FTV ENGINE CONTROL  ECD SYSTEM  Active Control Engine Mount System  


DESCRIPTION

The Active Control Engine Mount (ACM) system decreases engine vibration at low engine speed using the VSV for engine mount. The VSV is controlled by a pulse signal transmitted to the VSV from the ECM. The frequency of this pulse signal is matched to the engine speed to decrease engine vibration.

WIRING DIAGRAM

A221595E13
2.396,1.198 5.469,1.365 3.073,0.167 10 false Vacuum Switching Valve (for Engine Mounting) 2.385,1.042 2.813,1.25 0.427,0.208 10 false C80 1.042,0.917 1.792,1.188 0.75,0.271 10 false EFI No. 2 3.073,2.177 3.396,2.427 0.323,0.25 10 false EFI 3.833,2.74 4.104,2.927 0.271,0.188 10 false EFI 1.146,2.24 1.615,2.469 0.469,0.229 10 false P/I-B 1.458,0.677 1.583,0.844 0.125,0.167 10 false 2 1.063,0.677 1.188,0.844 0.125,0.167 10 false 1 4.604,0.698 4.729,0.865 0.125,0.167 10 false 2 3.594,0.698 3.719,0.865 0.125,0.167 10 false 1 5.188,0.792 5.521,1.01 0.333,0.219 10 false G57 5.188,2.417 5.594,2.646 0.406,0.229 10 false G58 5.542,2.333 6.031,2.583 0.49,0.25 10 false MREL 5.542,0.771 6.031,0.99 0.49,0.219 10 false ACM 5.271,2.25 5.448,2.417 0.177,0.167 10 false 11 4.479,1.906 4.604,2.073 0.125,0.167 10 false 4 4.479,2.26 4.604,2.427 0.125,0.167 10 false 2 2.698,2.26 2.823,2.427 0.125,0.167 10 false 3 2.698,1.896 2.823,2.063 0.125,0.167 10 false 1 2.646,2.427 2.948,2.646 0.302,0.219 10 false 1B 4.427,2.427 4.75,2.656 0.323,0.229 10 false 1B 4.427,2.063 4.708,2.24 0.281,0.177 10 false 1B 2.646,2.052 2.979,2.302 0.333,0.25 10 false 1C 0.802,2.906 1.281,3.083 0.479,0.177 10 false Battery 5.969,3.365 6.333,3.51 0.365,0.146 10 false ECM 5.229,0.625 5.427,0.823 0.198,0.198 10 false 10 2.865,3.135 4.708,3.479 1.844,0.344 10 false No. 1 Integration Relay (Engine Room Relay Block)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Warm up the engine.


b.

Connect the intelligent tester to the DLC3.


c.

Move the shift lever to N or P.


d.

Enter the following menus: Powertrain / Engine / Active Test / Control the ACM Inhibit.


e.

Hold the top part of the steering wheel, and turn the Active Test from OFF to ON. Check the engine vibration.

Result
Engine Vibration Proceed to
Increases A
Does not increase B



B

2.CHECK VACUUM

A

2.CHECK VACUUM
a.

Check if the vacuum hose cap is missing, if the hose is damaged, and if the air and vacuum hoses have looseness, disconnection or blockage.

OK:

Vacuum hose cap is not missing and hoses are normal.




OK

3.INSPECT VSV FOR ENGINE MOUNT

NG

REPLACE VACUUM HOSE

3.INSPECT VSV FOR ENGINE MOUNT

OK

4.CHECK HARNESS AND CONNECTOR (VSV FOR ENGINE MOUNT - ECM, EFI NO. 2 FUSE - VSV FOR ENGINE MOUNT)

NG

REPLACE VSV FOR ENGINE MOUNT

4.CHECK HARNESS AND CONNECTOR (VSV FOR ENGINE MOUNT - ECM, EFI NO. 2 FUSE - VSV FOR ENGINE MOUNT)
a.

Disconnect the VSV for engine mount connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C80-2 - C57-10 (ACM) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C80-2 or C57-10 (ACM) - Body ground Always 10 kΩ or higher



d.

Remove the EFI NO. 2 fuse from the engine room relay block.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI NO. 2 fuse (2) - C80-1 Always Below 1 Ω



f.

Reconnect the VSV for engine mount connector.


g.

Reconnect the ECM connector.


h.

Reinstall the EFI NO. 2 fuse.



OK

5.INSPECT ENGINE MOUNTING INSULATOR FRONT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT ENGINE MOUNTING INSULATOR FRONT
a.

Inspect the engine mounting insulator front.



OK

NG

REPLACE ENGINE MOUNTING INSULATOR FRONT