After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION).
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Common Rail (All).
Take a snapshot of the following Data List items.
A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting. The data in the list below is that of a normal vehicle, but as the data varies between individual vehicles, this data should only be used for reference.
Check the Data List at idling and at 4000 rpm with no load after the engine is warmed up.
NEXT
Check MAP and MAF in the snapshot taken in procedure 1 when the engine was running at 4000 rpm with no load.
| Result | Proceed to |
|---|---|
| MAP is below 90 kPa*1 | A |
| MAP is 105 kPa or more and MAF is 84 gm/sec or more*2 | B |
| Except above*3 | C |
The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc.
Standard atmospheric pressure is 101 kPa (1.0 kgf/cm2, 15 psi). For every 100 m (328 ft.) increase in elevation, pressure drops by 1 kPa (0.01 kgf/cm2, 0.1 psi). This varies by weather.
*1: There may be a problem in the turbocharger system.
*2: There may be a problem in the fuel system or intake system.
*3: There may be a problem in intake system or a problem with the EGR valve (valve stuck open or valve does not close).
A
B
C
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and Atmosphere Pressure.
Compare MAP and Atmosphere Pressure when the engine switch on (IG) (do not start the engine).
Difference between MAP and Atmosphere Pressure is less than 8 kPa.
If MAP and Atmosphere Pressure have the same value, both are normal. If there is a difference of 10 kPa or more, compare the values to the atmospheric pressure for that day. The sensor whose deviation is the greatest is malfunctioning.
Standard atmospheric pressure is 101 kPa (1.0 kgf/cm2, 15 psi). For every 100 m (328 ft.) increase in elevation, pressure drops by 1 kPa (0.01 kgf/cm2, 0.1 psi). This varies by weather.
| Result | Proceed to |
|---|---|
| MAP and Atmosphere Pressure have same value | A |
| MAP is different from actual atmospheric pressure | B |
| Atmosphere Pressure is different from actual atmospheric pressure | C |
A
B
C
Check for air leaks and blockages between the air cleaner case and turbocharger sub-assembly, and between the turbocharger sub-assembly and intake manifold.
| Result | Proceed to |
|---|---|
| No leaks or blockages in the intake system | A |
| Leaks and/or blockages exist in the intake system | B |
Inspect the intake system, especially hoses and pipes between the air cleaner and turbocharger sub-assembly.
Check for abnormal disconnections, pipe and hose squashing, and any damage in the intake system.
Using your hand, check whether the pipes and hoses in the intake system are securely connected.
By applying soapy water and revving up the engine, air leaks from the intake system can be checked by checking for bubbles.
Make sure that the hose between the manifold absolute pressure sensor and intake manifold is not loose or disconnected.
Check for any modifications in the intake system made by the user.
A
B
Inspect the turbocharger sub-assembly.
Click hereEngine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>INSPECTION
OK
NG
Check for intermittent problems.
NEXT
Replace the manifold absolute pressure sensor.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MANIFOLD ABSOLUTE PRESSURE SENSOR>REMOVAL
NEXT
Replace the ECM (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Repair or replace the malfunctioning part in the air intake system.
NEXT
Replace the turbocharger sub-assembly (See page Engine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>REMOVAL).
NEXT
Check for air leaks and blockages between the air cleaner case and turbocharger sub-assembly, and between the turbocharger sub-assembly and intake manifold.
| Result | Proceed to |
|---|---|
| No leaks or blockages in the intake system | A |
| Leaks and/or blockages exist in the intake system | B |
Inspect the air intake system, especially hoses and pipes between the air cleaner and turbocharger sub-assembly.
Check for abnormal disconnections, pipe and hose squashing, and any damage in the intake system.
Using your hand, check whether the pipes and hoses in the intake system are securely connected.
By applying soapy water and revving up the engine, air leaks from the intake system can be checked by checking for bubbles.
Make sure that the hose between the manifold absolute pressure sensor and intake manifold is not loose or disconnected.
Check for any modifications in the intake system made by the user.
A
B
Connect the GTS to the DLC3.
Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.
Turn the engine switch off. Wait for 30 seconds, and then restart the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.
Read the MAF value displayed on the GTS while the engine is idling.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the EGR Valve Close.
Read the MAF value when the EGR valve is closed using the Active Test function.
If idling continues for 20 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or restart the engine.
Before performing the diagnosis, confirm that the EGR valve target opening angle is not 0%.
When idling the engine, the EGR cooler sub-assembly is bypassed.
| Active Test | Result | Proceed to |
|---|---|---|
| Activate the EGR Valve Close:
Off (Open) to On (Closed) |
MAF value does not change | B |
| MAF value changes | A |
As the measured values may differ from those shown below due to factors such as differences in measuring environments and changes in vehicle condition due to aging, do not use these values to determine whether the vehicle is malfunctioning or not.
The problem may be a temporary one, due to the entry of deposits or foreign matter. Check that there are no deposits or foreign matter in the electric EGR control valve assembly or mass air flow meter sub-assembly.
| EGR Valve Condition (Opening) | Measuring Condition | MAF (Reference) |
|---|---|---|
| Open (41%) | ·
Atmosphere pressure: 101 kPa ·
Engine coolant temperature: 75°C (167°F) |
3 to 7 gm/sec |
| Closed (0%) | 11 to 16 gm/sec |
A
B
Connect the GTS to the DLC3.
Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.
Turn the engine switch off and wait for 30 seconds.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.
Read the MAF value displayed on the GTS while the engine is idling.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for EGR Cooler Bypass / Data List / EGR Cooler Bypass Position.
Whether the EGR is passing through the bypass side or cooler side during the Active Test can be confirmed by checking EGR Cooler Bypass Position.
Using the Active Test function, switch the EGR valve bypass switching valve between "Cooler" and "Bypass" a few times, and then check whether the MAF value changes after switching the valve from "Cooler" to "Bypass".
If idling continues for 20 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or restart the engine.
When operating "Activate the VSV for EGR Cooler Bypass", check that "Cooler" and "Bypass" can be switched between and the EGR cooler by-pass valve regulating link operates. If the link does not operate, the inspection cannot be performed correctly. Therefore, inspect and repair the following parts, perform the Active Test and read the changes in the MAF value.
No. 2 EGR valve assembly (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).
Vacuum hose connection (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).
No. 1 vacuum switching valve assembly (for EGR bypass valve) (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR BYPASS VALVE SWITCHING VALVE>INSPECTION).
| GTS Display | Result | Proceed to |
|---|---|---|
| Activate the VSV for EGR Cooler Bypass:
Cooler to Bypass |
MAF value does not change | A |
| MAF value changes | B |
If the No. 1 EGR cooler is clogged, the mass air flow changes.
A
B
Repair or replace the malfunctioning part in the intake system.
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed and MAF.
Start the engine and read the value when 30 seconds has elapsed.
| Engine Speed | MAF |
|---|---|
| Idling | ·
3.0 to 15.0 gm/sec (EGR on) ·
10.0 to 21.0 gm/sec (EGR off) |
| Running without load (3000 rpm): | ·
45.0 to 89.0 gm/sec (EGR on) ·
72.0 to 94.0 gm/sec (EGR off) |
OK
NG
Connect the GTS to the DLC3.
Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.
Turn the engine switch off and wait for 30 seconds.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.
Read the MAF value displayed on the GTS while the engine is idling.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for EGR Cooler Bypass / Data List / EGR Cooler Bypass Position.
Whether the EGR is passing through the bypass side or cooler side during the Active Test can be confirmed by checking EGR Cooler Bypass Position.
Using the Active Test function, switch the EGR valve bypass switching valve between "Cooler" and "Bypass" a few times, and then check whether the MAF value changes after switching the valve from "Cooler" to "Bypass".
If idling continues for 20 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or restart the engine.
When operating "Activate the VSV for EGR Cooler Bypass", check that "Cooler" and "Bypass" can be switched between and the EGR cooler by-pass valve regulating link operates. If the link does not operate, the inspection cannot be performed correctly. Therefore, inspect and repair the following parts, perform the Active Test and read the changes in the MAF value.
No. 2 EGR valve assembly (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).
Vacuum hose connection (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).
No. 1 vacuum switching valve assembly (for EGR bypass valve) (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR BYPASS VALVE SWITCHING VALVE>INSPECTION).
| GTS Display | Result | Proceed to |
|---|---|---|
| Activate the VSV for EGR Cooler Bypass:
Cooler to Bypass |
MAF value does not change | A |
| MAF value changes | B |
If the No. 1 EGR cooler is clogged, the mass air flow changes.
A
B
Remove the electric EGR control valve assembly (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE>REMOVAL).
Visually check the electric EGR control valve assembly for deposits.
If there are deposits, clean the electric EGR control valve assembly.
When cleaning the electric EGR control valve assembly, make sure the valve is completely closed.
When cleaning the electric EGR control valve assembly, perform initialization procedure (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).
Do not forcibly open the valve, as it may be damaged or deformed.
When cleaning the electric EGR control valve assembly, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in the solvent may damage the parts.
If the EGR valve does not open properly or is stuck closed, the amount of intake air increases and combustion sounds and engine vibration may increase.
If the EGR valve does not close properly or is stuck open, EGR becomes excessive and combustion becomes unstable. Also, there may be a lack of power.
Reinstall the electric EGR control valve assembly (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE>INSTALLATION).
NEXT
Replace the No. 1 EGR cooler (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR COOLER>REMOVAL).
NEXT
Replace the mass air flow meter sub-assembly (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL).
If foreign matter is stuck inside the mass air flow meter sub-assembly, the output characteristics of the mass air flow meter sub-assembly may change, resulting in a malfunction.
NEXT
Connect the GTS to the DLC3.
Turn the GTS on.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Swirl Control Valve.
Perform the Active Test.
Swirl control valve rod moves smoothly in the direction indicated by the arrow in the illustration.
NEXT
NEXT