Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  U029D  Lost Communication with NOx Sensor "A"  


DESCRIPTION

The ECM sends and receives data to and from the nitrogen oxides sensor via local CAN communication.

U029D
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Turn the engine switch on (IG) and wait for 1.6 seconds or more. Communication stops between the ECM and the nitrogen oxides sensor for 1.6 seconds or more.
(1 trip detectionlogic)
·

Nitrogen oxides sensor

·

Harness or connector

·

ECM



MONITOR DESCRIPTION

The ECM stores a DTC when a communication malfunction occurs between the nitrogen oxides sensor and ECM.

WIRING DIAGRAM

A390307E01
6.24,4.323 6.698,4.521 0.458,0.198 10 false ECM 6.24,4.146 6.698,4.344 0.458,0.198 10 false G184 5.792,3.604 6.104,3.802 0.313,0.198 10 false 14 6.031,3.49 6.573,3.708 0.542,0.219 10 false MREL 6.042,0.292 6.583,0.51 0.542,0.219 10 false CANU 6.042,0.823 6.583,1.042 0.542,0.219 10 false CAND 5.781,0.5 6.094,0.698 0.313,0.198 10 false 27 5.771,1 6.083,1.198 0.313,0.198 10 false 35 4.5,0.49 4.813,0.688 0.313,0.198 10 false 4 4.5,0.99 4.813,1.188 0.313,0.198 10 false 3 4.5,1.333 4.813,1.531 0.313,0.198 10 false 2 4.01,0.281 4.552,0.5 0.542,0.219 10 false CAN+ 3.594,0.271 4.135,0.49 0.542,0.219 10 false BATT 4.052,0.781 4.594,1 0.542,0.219 10 false CAN- 4.094,1.208 4.635,1.427 0.542,0.219 10 false GND 3.531,1.594 4.073,1.813 0.542,0.219 10 false s6 3.521,1.781 5.146,2.031 1.625,0.25 10 false Nitrogen Oxides Sensor 3.719,3.802 4.802,4.031 1.083,0.229 10 false EFI MAIN1 1.865,1.042 2.667,1.292 0.802,0.25 10 false NOx PM 3.396,0.375 3.708,0.573 0.313,0.198 10 false 1 0.917,0.417 1.719,0.667 0.802,0.25 10 false NOx PM 1.677,0.854 1.99,1.052 0.313,0.198 10 false 2 2.51,0.385 2.823,0.583 0.313,0.198 10 false 3 2.521,0.854 2.833,1.052 0.313,0.198 10 false 1 1.677,0.375 1.99,0.573 0.313,0.198 10 false 5 0.979,3.219 1.781,3.469 0.802,0.25 10 false P/B-B 0.75,4.823 1.552,5.073 0.802,0.25 10 false Battery 2.365,5.365 4.365,5.646 2,0.281 10 false : CAN Communication Line 2.448,3.229 3.531,3.458 1.083,0.229 10 false EFI-MAIN NO. 1 2.021,2.875 2.333,3.073 0.313,0.198 10 false 1 2.031,3.292 2.344,3.49 0.313,0.198 10 false 3 5.24,2.896 5.552,3.094 0.313,0.198 10 false 10 5.292,3.292 5.604,3.49 0.313,0.198 10 false 7 1.99,3.073 2.531,3.292 0.542,0.219 10 false 1C 5.24,3.073 5.781,3.292 0.542,0.219 10 false 1J 5.24,3.469 5.781,3.688 0.542,0.219 10 false 1K 3.281,4.26 5.094,4.573 1.813,0.313 10 false NO. 1 Integration Relay 1.99,3.479 2.531,3.698 0.542,0.219 10 false 1J

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

According to the display on the GTS, select "Health Check".


d.

Check for currently output system DTCs.

Result:
Result Proceed to
DTC U029D is output A
DTC U029D and other DTCs are output* B


HINT:

*If any other DTCs are output, perform troubleshooting for those DTCs first.




A

2.CHECK NITROGEN OXIDES SENSOR

B

2.CHECK NITROGEN OXIDES SENSOR
a.

Disconnect the nitrogen oxides sensor connector.


b.

Turn the engine switch on (IG).


c.
A383897C02
1.469,0.198 1.948,0.531 0.479,0.333 1.052,1.833 1.156,1.833 1.156,1.833 1.281,1.271 true 1.792,1.833 1.625,1.833 1.625,1.833 1.49,1.271 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.823,1.75 2.281,1.948 0.458,0.198 10 false GND 0.688,1.76 1.229,1.958 0.542,0.198 10 false BATT 1.646,0.292 2.104,0.49 0.458,0.198 10 false s6
*1 Front view of wire harness connector
(to Nitrogen oxides sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
s6-1 (BATT) - s6-2 (GND) Engine switch on (IG) 11 to 14 V




OK

3.CHECK HARNESS AND CONNECTOR (NITROGEN OXIDES SENSOR - ECM)

NG

7.INSPECT NOX PM RELAY
3.CHECK HARNESS AND CONNECTOR (NITROGEN OXIDES SENSOR - ECM)
a.

Disconnect the nitrogen oxides sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
s6-4 (CAN+) - G184-27 (CANU) Always Below 1 Ω
s6-3 (CAN-) - G184-35 (CAND) Always Below 1 Ω
s6-4 (CAN+) or G184-27 (CANU) - Body ground and other terminals Always 10 kΩ or higher
s6-3 (CAN-) or G184-35 (CAN-) - Body ground and other terminals Always 10 kΩ or higher




OK

4.REPLACE NITROGEN OXIDES SENSOR

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

4.REPLACE NITROGEN OXIDES SENSOR
a.


NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Turn the engine switch off for 30 seconds.



NEXT

6.CHECK DTC OUTPUT
6.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) wait for 1.6 seconds or more.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
No DTC is output A
DTC U029D is output B




A

END

B

7.INSPECT NOX PM RELAY

OK

8.CHECK HARNESS AND CONNECTOR (NITROGEN OXIDES SENSOR - ENGINE RELAY BLOCK, BATTERY - ENGINE RELAY BLOCK)

NG

REPLACE NOX PM RELAY

8.CHECK HARNESS AND CONNECTOR (NITROGEN OXIDES SENSOR - ENGINE RELAY BLOCK, BATTERY - ENGINE RELAY BLOCK)
a.

Disconnect the nitrogen oxides sensor connector.


b.

Remove the NOx PM relay from the engine relay block.


c.

Measure the resistance according to the value(s) in the table below.

A390308C01
1.521,0.552 1.969,0.865 0.448,0.313 1.333,1.625 1.063,2.26 1.063,2.26 0.927,2.26 true 0.583,0.427 0.896,0.625 0.313,0.198 10 false *a 4.906,0.208 5.219,0.406 0.313,0.198 10 false *1 3.615,1.365 3.927,1.563 0.313,0.198 10 false *b 1.667,0.625 1.979,0.823 0.313,0.198 10 false s6 0.552,2.188 1.375,2.406 0.823,0.219 10 false BATT
*1 Engine Relay Block - -
*3 Front view of wire harness connector
(to Nitrogen oxides sensor)
*b Front view of wire harness connector
(to NOx PM Relay)


Standard Resistance:
Tester Connection Condition Specified Condition
s6-1 (BATT) - NOx PM relay terminal 3 Always Below 1 Ω
s6-2 (GND) - Body ground Always Below 1 Ω
NOx PM relay terminal 2 - Body ground Always Below 1 Ω
NOx PM relay terminal 3 or s6-1 (BATT) - Body ground and other terminals Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
NOx PM relay terminal 5 - Body ground Always 11 to 14 V




OK

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR