Home › Engine / Hybrid System › 1GR-FE (ENGINE MECHANICAL) › ENGINE UNIT
RM27T0E _51 Engine / Hybrid System _053662 1GR-FE ENGINE MECHANICAL _0260494 ENGINE UNIT A

1GR-FE ENGINE MECHANICAL  ENGINE UNIT  REMOVAL  


PROCEDURE

Hide 1.REMOVE ENGINE WIRE

Hide 2.DISCONNECT HEATER WATER HOSE ASSEMBLY

a.
A223694E02
0.042,0.031 0.625,0.281 0.583,0.25 10 true *A 0.083,1.688 0.698,1.969 0.615,0.281 10 true *B

w/o Warmer:

Disconnect the 2 hoses and remove the heater water hose assembly.

Text in Illustration
*A w/o Warmer
*B w/ Warmer


b.

w/ Warmer:

Disconnect the 3 hoses and remove the heater water hose assembly.


Hide 25701 3.REMOVE EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)

a.
A225367

Remove the 3 nuts and emission control valve set.


Hide 25702 4.REMOVE NO. 2 EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)

a.
A225368

Remove the 3 nuts and No. 2 emission control valve set.


Hide 19500 5.REMOVE IGNITION COIL ASSEMBLY

a.
A224724

Remove the 6 bolts and 6 ignition coils.


Hide 11181A 6.REMOVE REAR CYLINDER HEAD COVER

Hide 7.REMOVE FUEL PIPE SUB-ASSEMBLY

a.
A224750

Disconnect the 2 fuel pipes (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).


b.

Remove the 2 bolts and No. 1 fuel pipe and No. 2 fuel pipe.


Hide 23807 8.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 23250 9.REMOVE FUEL INJECTOR ASSEMBLY

Hide 16206 11.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY (w/ Oil Cooler)

Hide 16603 12.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

Hide 16604 13.REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

Hide 16620 14.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 11452 15.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 12315 16.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH

a.
A221156

Remove the 3 bolts and front No. 1 engine mounting bracket LH.


Hide 12311 17.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH

a.
A221155

Remove the 4 bolts and front No. 1 engine mounting bracket RH.


Hide 13453 18.REMOVE FLYWHEEL RING GEAR (for Manual Transmission)

HINT:

If the flywheel ring gear is deformed or the gears are damaged, replace it.


CAUTION:

Wear protective gloves. Hot areas on the flywheel ring gear may injure your hands.


a.
A177669E01
1.248,2.868 1.372,3.010 0.124,0.142 10 1 2.226,3.838 2.350,3.980 0.124,0.142 10 2 0.58,3.528 0.704,3.670 0.124,0.142 10 3 2.713,3.395 2.837,3.538 0.124,0.142 10 4 1.178,3.989 1.302,4.132 0.124,0.142 10 5 2.145,2.86 2.269,3.003 0.124,0.142 10 6

Using a torch, heat the ring gear evenly to approximately 200°C (392°F).


b.

Temporarily install 6 bolts (8 mm (0.315 in.) x 1.25 pitch) with a length of 70 mm (2.76 in.) or more to the flywheel.


c.

Uniformly tighten the 6 bolts in the order shown in the illustration.


d.

Remove the ring gear from the flywheel.