Home › Engine / Hybrid System › 1KD-FTV (ENGINE MECHANICAL) › ENGINE UNIT › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053664 1KD-FTV ENGINE MECHANICAL _0260509 ENGINE UNIT A

1KD-FTV ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL REAR CRANKSHAFT OIL SEAL

a.
A253830E01
1.656,1.167 0.885,1.167 false 1.323,1.594 1.177,1.594 1.177,1.594 1.177,1.167 false 0.521,1.083 0.823,1.25 0.302,0.167 10 false SST

Using SST and a hammer, tap in a new oil seal until its surface is flush with the rear oil seal retainer edge.

SST
09518-36030  
09950-70010  (09951-07100)


b.

Apply MP grease to the lip of the oil seal.


Hide 11301C 2.INSTALL SUPPLY PUMP OIL SEAL

a.
A058118E03
1.823,1.333 2.406,1.333 2.406,1.333 1.698,1.021 false 1.885,1.5 2.406,1.333 false 2.438,1.26 2.792,1.417 0.354,0.156 10 false SST

Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing gear cover edge.

SST
09223-15020  
09502-12010  
09950-70010  (09951-07100)


b.

Apply MP grease to the lip of the oil seal.


Hide 3.INSTALL FRONT CRANKSHAFT OIL SEAL

a.
A058119E02
1.792,1.24 2.385,1.344 false 2.417,1.25 2.75,1.417 0.333,0.167 10 false SST

Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing gear cover edge.

SST
09214-76011  


b.

Apply MP grease to the lip of the oil seal.


Hide 11381 4.INSTALL REAR ENGINE OIL SEAL RETAINER

a.

Remove any old seal packing (FIPG material) from the oil pan and cylinder block.


b.
A380862E01
2.219,0.771 2.469,0.365 2.469,0.365 2.615,0.365 true 1.479,3.792 1.104,4.208 1.104,4.208 0.917,4.208 true 2.635,0.26 2.948,0.458 0.313,0.198 10 false *1 0.729,4.115 0.958,4.313 0.229,0.198 10 false *1

Apply seal packing to the places shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

4 mm (0.157 in.)


Text in Illustration
*1 Seal Packing

NOTICE:

After applying seal packing, install the rear engine oil seal retainer within 3 minutes and tighten the bolts within 15 minutes.



c.
U169067E02
1.229,1.604 1.396,1.865 0.167,0.26 6 true . 1.75,1.813 1.938,2.073 0.188,0.26 6 true . 1.281,1.406 1.333,1.604 0.052,0.198 6 true . 1.792,1.625 1.844,1.823 0.052,0.198 6 true .

Install the retainer with the 5 bolts. Alternately tighten the 5 bolts in several passes.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 13633 5.INSTALL NO. 2 BALANCESHAFT DRIVEN GEAR

a.
U169048

Mount the balanceshaft between aluminum plates in a vise.

NOTICE:

Be careful not to damage the balanceshaft.



b.

Align the balanceshaft knock pin with the knock pin hole. Then install the balanceshaft thrust washer and balanceshaft driven gear.


c.

Install the bolt.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


Hide 13602 6.INSTALL NO. 2 BALANCESHAFT SUB-ASSEMBLY

a.
A051334

Install the balanceshaft with the 2 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 13632 7.INSTALL NO. 1 BALANCESHAFT DRIVEN GEAR

a.
A051333

Mount the balanceshaft between aluminum plates in a vise.

NOTICE:

Be careful not to damage the balanceshaft.



b.

Align the balanceshaft knock pin with the knock pin hole. Then install the balanceshaft thrust washer and balanceshaft driven gear.


c.

Install the bolt.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


Hide 13601A 8.INSTALL NO. 1 BALANCESHAFT SUB-ASSEMBLY

a.
A051332

Install the balanceshaft with the 2 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 11320 9.INSTALL TIMING GEAR CASE ASSEMBLY

a.

Remove any old seal packing (FIPG material).


b.
A075511E10
1.26,1.219 0.438,1.635 0.438,1.635 0.438,1.74 false 2.135,1 2.469,0.24 2.469,0.24 2.542,0.24 false 0.354,1.75 0.531,1.948 0.177,0.198 10 false *2 2.573,0.156 2.781,0.323 0.208,0.167 10 false *1

Apply seal packing to the timing gear case as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

5 mm (0.197 in.)


Text in Illustration
*1 New Gasket
*2 Seal Packing

NOTICE:

After applying seal packing, install the timing gear case assembly within 3 minutes and tighten the bolts within 15 minutes.



c.
A060151E04
2.417,0.896 2.99,0.896 false 3,0.802 3.177,0.979 0.177,0.177 10 false *1

Install a new gasket to the groove of the timing gear case.

Text in Illustration
*1 New Gasket


d.
A069840E02
0.906,0.948 0.604,0.948 false 1.146,1.854 0.844,1.854 false 0.417,0.865 0.563,1.042 0.146,0.177 10 false *1 0.656,1.771 0.802,1.948 0.146,0.177 10 false *1

Install 2 new O-rings to the cylinder block.

Text in Illustration
*1 New O-Ring


e.
A069841

Align the "2" marks of the balanceshaft driven gear No. 1 and oil pump drive gear.


f.

Align the mark on the oil pump drive gear with the mark on the timing gear case.


g.
A069842E03
1.563,0.698 1.771,0.865 0.208,0.167 10 true (A)

Install the timing gear case with the union bolt and 8 bolts.

Torque:
for union bolt (A) : 16 N*m (163 kgf*cm, 12 ft.*lbf)
for bolt : 13 N*m (133 kgf*cm, 10 ft.*lbf)


h.
A060154

Remove the screw plug and gasket.


i.

Pour approximately 50 cc (3.05 cu. in.) of engine oil into the oil pump.


j.

Install a new gasket and the screw plug.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 12101 10.INSTALL OIL PAN SUB-ASSEMBLY

a.

Remove any old seal packing (FIPG material) and be careful not to drop any oil on the contact surfaces of the cylinder block, rear oil seal retainer and oil pan.


b.

Install a new gasket to the cylinder block.


c.
A225304E01
0.298,1.74 0.486,1.891 0.188,0.151 10 *1 0.689,1.667 0.554,1.829 0.554,1.829 0.504,1.829 false

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

4 mm (0.157 in.)


Text in Illustration
*1 Seal Packing

NOTICE:
·

Remove any oil from the contact surface.

·

Install the oil pan within 3 minutes after applying seal packing.

·

Do not start the engine for at least 2 hours after installation.




d.

Install the oil pan with the 22 bolts and 2 nuts.

Torque:
15 N*m (148 kgf*cm, 11 ft.*lbf)


Hide 15104 11.INSTALL OIL STRAINER SUB-ASSEMBLY

a.

Install a new gasket and the oil strainer with the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 12102A 12.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

a.

Remove any old seal packing (FIPG material).


b.
A225305E01
2.082,1.123 2.619,1.123 false 2.624,1.032 2.781,1.189 0.157,0.157 10 *1

Apply seal packing to the No. 2 oil pan as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

4 mm (0.157 in.)


Text in Illustration
*1 Seal Packing

NOTICE:
·

Remove any oil from the contact surface.

·

Install the No. 2 oil pan within 3 minutes after applying seal packing.

·

Do not start the engine for at least 2 hours after installation.




c.

Install the No. 2 oil pan with the 13 bolts and 2 nuts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 13521 13.INSTALL CRANKSHAFT TIMING GEAR

A061827E02
2.25,1.063 2.979,1.708 true 2.833,1.74 3.156,1.927 0.323,0.188 10 false SST

a.

Position the crankshaft timing gear with timing mark 1 facing forward.


b.

Align the key groove of the crankshaft timing gear with the set key on the crankshaft.


c.

Using SST and a hammer, tap on the timing gear to install it.

SST
09223-00010  


Hide 13613E 14.INSTALL INJECTION GEAR

a.

Install a new O-ring and the supply pump with the 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Temporarily install the injection gear with the nut.

HINT:

Fit the key (protrusion) of the supply pump into the key slot of the injection gear.



c.
A069843

Align the "3" marks of the balanceshaft driven gear No. 2 and injection gear.


d.
A069844E02
1.271,1.677 0.948,2 0.948,2 0.854,2 true 0.667,1.906 0.844,2.094 0.177,0.188 10 false *1

Install a new O-ring to the injection gear.

Text in Illustration
*1 New O-Ring


e.
A069845E02
2.885,1 2.823,1.313 false 2.698,1.344 3.052,1.521 0.354,0.177 10 false SST

Install the injection gear set nut.


f.

Using SST, tighten the nut.

SST
09960-10010  (09962-01000, 09963-01000)

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 13538 15.INSTALL NO. 2 IDLE SUB GEAR

a.
A069847E03
2.792,1.448 2.208,1.865 2.208,1.865 2.125,1.865 false 1.906,1.781 2.104,1.927 0.198,0.146 10 false *1

Mount the No. 1 idle gear in a vise.

Text in Illustration
*1 Cutout Mark

HINT:

Make sure the cutout mark of the idle gear faces down.


NOTICE:

Be careful not to damage the gear.



b.
A069848E03
1.99,0.156 2.5,0.156 false 1.99,1 2.5,1 false 1.448,0.531 0.896,0.531 false 0.719,0.438 0.875,0.594 0.156,0.156 10 false *2 2.51,0.052 2.677,0.229 0.167,0.177 10 false *1 2.51,0.906 2.677,1.083 0.167,0.177 10 false *3

Install the idle gear spring.

Text in Illustration
*1 Wave Washer
*2 No. 2 Idle Sub Gear
*3 Idle Gear Spring


c.

Install the No. 2 idle sub gear.


d.

Install the wave washer.

HINT:

Fit the pins on the gears between the spring ends.



e.
A069834

Using snap ring pliers, install the shaft snap ring.


f.
A069850E03
2.073,1.823 2.073,1.615 false 2.5,0.573 2.615,0.573 2.615,0.573 2.875,1.177 false 1.969,1.833 2.156,1.99 0.188,0.156 10 false *1 2.125,0.49 2.448,0.646 0.323,0.156 10 false SST

Using SST, align the holes of the No. 1 idle gear and No. 2 idle sub gear by turning the No. 2 idle sub gear clockwise and install a service bolt.

SST
09960-10010  (09962-01000, 09963-00700)

Text in Illustration
*1 Service Bolt


g.

Remove the No. 1 idle gear from the vise and turn it upside down.


Hide 13537 16.INSTALL NO. 1 IDLE SUB GEAR

a.
A069851E02
0.958,0.948 1.177,1.135 0.219,0.188 10 false *1

Mount the No. 1 idle gear and No. 2 idle sub gear in a vise.

Text in Illustration
*1 Upward

NOTICE:

Be careful not to damage the gears.



b.
A069852E02
1.375,0.896 1.073,1.469 1.073,1.469 1.073,1.583 false 0.979,1.604 1.156,1.76 0.177,0.156 10 false *1

Remove the service bolt.

Text in Illustration
*1 Service Bolt


c.
A069853E03
1.917,0.208 2.469,0.208 false 1.917,1.125 2.469,1.125 false 1.354,0.646 0.781,0.646 false 0.594,0.563 0.771,0.729 0.177,0.167 10 false *2 2.479,0.115 2.656,0.281 0.177,0.167 10 false *1 2.479,1.031 2.656,1.198 0.177,0.167 10 false *3

Install the idle gear spring.

Text in Illustration
*1 Wave Washer
*2 No. 1 Idle Sub Gear
*3 Idle Gear Spring


d.

Install the No. 1 idle sub gear.


e.

Install the wave washer.

HINT:

Fit the pins on the gears between the spring ends.



f.
A069832

Using a snap ring pliers, install the shaft snap ring.


g.
A069854E02
1.031,0.417 0.802,0.594 0.802,0.594 0.646,0.594 false 2.948,0 3.417,0 false 2.073,0.292 2.49,0.292 false 2.521,0.208 2.729,0.375 0.208,0.167 10 false *1 0.323,0.51 0.656,0.667 0.333,0.156 10 false SST 0.906,0.969 1.104,1.135 0.198,0.167 10 false *2

Using SST, align the holes of the No. 1 idler gear and No. 1 idle sub gear by turning the No. 1 idle sub gear clockwise, and install the service bolt.

SST
09960-10010  (09962-01000, 09963-00600)

Text in Illustration
*1 Service Bolt
*2 Upward


Hide 13581 17.INSTALL NO. 1 IDLE GEAR SHAFT

a.
A069846E01
2.302,1.219 2.052,1.708 2.052,1.708 1.958,1.708 false 1.729,1.625 1.927,1.802 0.198,0.177 10 false *1

Apply a coat of engine oil to the No. 1 idle gear shaft.

Text in Illustration
*1 Engine Oil


b.
A060159E07
1.573,1.063 1.208,0.521 1.208,0.521 1.073,0.521 false 0.865,0.427 1.063,0.625 0.198,0.198 10 true *1

Install the gear shaft as shown in the illustration.

Text in Illustration
*1 Oil Hole


Hide 13525 18.INSTALL NO. 1 IDLE GEAR

a.
G036757E03
1.948,0.615 2.552,0.281 2.552,0.281 2.698,0.281 true 2.052,0.063 2.281,0.26 0.229,0.198 10 true *1 2.75,0.198 3.083,0.354 0.333,0.156 10 false SST

Align the "5" timing marks of the idle gear and crankshaft timing gear.

Text in Illustration
*1 Turn


b.

Using SST, turn the injection gear and align the "4" timing marks of the idle gear and injection gear, and then mesh the gears.

SST
09960-10010  (09962-01000, 09963-00700)


c.
A222334E02
2.458,1.656 1.427,1.802 1.427,1.802 1.271,1.802 true 1.063,1.708 1.24,1.875 0.177,0.167 10 false *1

Position the thrust plate with the protrusion facing forward.

Text in Illustration
*1 Service Bolt


d.

Align the bolt holes and install the thrust plate with the 2 bolts.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


e.

Remove the service bolt.


Hide 19315 19.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

A051411

a.

Align the key groove of the sensor plate with the set key.


b.

Install the sensor plate with the cupped side facing outward.


Hide 20.INSTALL TIMING GEAR COVER

a.

Remove any old seal packing (FIPG material).


b.
A225340E01
1.681,0.763 1.929,0.401 1.929,0.401 1.999,0.401 false 2.014,0.32 2.185,0.479 0.171,0.159 10 *1

Apply seal packing to the timing gear cover as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

4 mm (0.157 in.)


Text in Illustration
*1 Seal Packing

NOTICE:

After applying seal packing, install the timing gear cover within 3 minutes and tighten the bolts within 15 minutes.



c.
A060162E02
1.844,1.688 1.375,1.927 1.375,1.927 1.313,1.927 false 1.094,1.854 1.292,2.01 0.198,0.156 10 false *1

Install a new O-ring to the timing gear case.

Text in Illustration
*1 New O-Ring


d.
A051308

Install the timing gear cover with the 14 bolts and 2 nuts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 16100 21.INSTALL WATER PUMP ASSEMBLY

a.
A225339

Install a new gasket and the water pump with the 5 bolts and 2 nuts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 13751 24.INSTALL VALVE LIFTER

a.

Install the valve lifter.


b.

Check that the valve lifter rotates smoothly by hand.


Hide 12108 34.INSTALL OIL FILLER CAP SUB-ASSEMBLY