Home › Engine / Hybrid System › 1KD-FTV (FUEL) › FUEL INJECTOR › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053669 1KD-FTV FUEL _0260567 FUEL INJECTOR A

1KD-FTV FUEL  FUEL INJECTOR  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.

·

After removing the injection pipes, clean them with a brush and compressed air.



PROCEDURE

Hide 23670 1.INSTALL INJECTOR ASSEMBLY

NOTICE:

Be sure to install the injector, No. 1 nozzle holder clamp, washer and bolt in their original positions.


a.
B008252E02
2.031,1.104 2.188,1.302 0.156,0.198 10 false .

Install 4 new injection nozzle seats to the cylinder head.


b.

Apply a small amount of clean engine oil to 4 new O-rings.


c.
G036760E10
2.698,0.708 2.594,0.708 2.594,0.708 2.333,1.177 false 2.719,0.615 2.969,0.802 0.25,0.188 10 false *1

Install an O-ring to each injector as shown in the illustration.

Text in Illustration
*1 New O-Ring


d.

Insert the 4 injectors into the cylinder head.

NOTICE:
·

Insert the injector until it touches the injection nozzle seat surface.

·

After installing the injector to the cylinder head, the O-ring may prevent the injector from fully seating. If so, pull out the injector and reinstall it.

·

Always return an injector to the same place it was removed from.




e.

For an injector that has been replaced with a new injector, register the injector compensation code (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).


f.
A060177E09
1.073,0.083 1.344,0.083 false 1.375,0.01 1.563,0.156 0.188,0.146 10 false *1 0.771,0.302 0.958,0.448 0.188,0.146 10 false *a

Temporarily install 4 new washers and the 4 No. 1 nozzle holder clamps with the 4 bolts.

Text in Illustration
*1 Washer
*a Downward

HINT:

Apply a small amount of engine oil to the threads and under the heads of the clamp bolts.


NOTICE:
·
G037744E08
1.74,0.344 1.146,0.344 false 1.49,1.5 1.333,1.5 1.333,1.5 1.333,0.344 false 0.938,0.26 1.125,0.406 0.188,0.146 10 false *1


·

The fork portion of the nozzle holder clamp must be set on the injector.

·

Before tightening the bolts, check that the No. 1 nozzle holder clamp is set properly.

·

When installing the clamp bolts, first tighten them by hand until they cannot be turned further. Then, tighten the bolts to the specified torque in the following step.

·

When tightening the bolts, pay attention so as not to tilt the bolt and the clamp.

·

Do not reuse the washer.

·

If the nozzle leakage pipe is accidentally tightened beyond the torque specification, it must be replaced.

Text in Illustration
*1 Nozzle Clamp Holder




g.

Temporarily install the 4 injection pipes with the union nuts.

HINT:

To position the injectors, loosely tighten the union nut.



h.
A062123E11
1.99,1.594 2.146,1.792 0.156,0.198 10 false .

Check the nozzle leakage pipe. Check that there are no scratches or dents on the 5 union seal surfaces.

If scratches or dents are present, replace the nozzle leakage pipe.


i.
A070538E06
2.406,0.313 2.656,0.313 false 0.563,2.927 0.698,3.115 0.698,3.115 0.813,3.115 false 2.688,0.229 2.865,0.375 0.177,0.146 10 false *1 0.844,3.031 1.021,3.177 0.177,0.146 10 false *2

Set the leakage pipe and 5 new gaskets in place.

Text in Illustration
*1 Union Bolt
*2 Hollow Screw


j.

Apply a small amount of oil to the 4 injector hollow screws and union bolt.


k.

Temporarily install the leakage pipe with the 4 injector hollow screws and union bolt.


l.

Tighten the 4 holder clamp bolts.

Torque:
22 N*m (220 kgf*cm, 16 ft.*lbf)


m.
U169047E02
1.125,0.385 1.708,0.385 false 0.167,0.865 0.365,1.135 0.198,0.271 10 false 4 0.646,1.125 0.844,1.365 0.198,0.24 10 false 3 1.115,1.375 1.292,1.563 0.177,0.188 10 false 2 1.583,1.646 1.75,1.833 0.167,0.188 10 false 1 1.74,0.292 1.979,0.49 0.24,0.198 10 false *1

Tighten the 4 hollow screws in order from 1 to 4.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)

Text in Illustration
*1 Union Bolt

NOTICE:

If a hollow screw is accidentally tightened beyond the torque specification, it must be replaced.



n.

Tighten the union bolt.

Torque:
13 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:

If the union bolt is accidentally tightened beyond the torque specification, it must be replaced.



o.

Remove the 4 injection pipes.


Hide 2.INSPECT FOR FUEL LEAK

a.
A154541E03
2.411,0.158 2.728,0.303 0.317,0.145 10 SST 2.782,0.245 2.942,0.245 2.942,0.245 2.942,1.412 false

Check that there are no leaks from the nozzle leakage pipe connection.

i.

Install the gasket and No. 2 nozzle leakage pipe to the cylinder head with SST (check valve).

Part No.:

23762-27010 (No. 2 nozzle leakage pipe)

90904-30012 (Gasket)


SST
09280-00010  

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


ii.

Apply a small amount of soapy water (or other fluid for detecting fuel leakage) on the nozzle leakage pipe connection.


iii.
A154542E04
2.146,1.333 2.052,1.333 2.052,1.333 1.771,1.51 true 2.198,1.25 2.656,1.531 0.458,0.281 10 true SST

Install SST (turbocharger pressure gauge) to the fuel return side of the leakage pipe, maintain 100 kPa (1.0 kgf/cm2, 15 psi) of pressure for 60 seconds and check that no bubbles form.

SST
09992-00242  


iv.

After checking for fuel leaks, wipe off the soapy water from the leakage pipe connection.


v.

Remove SST, the No. 2 nozzle leakage pipe and gasket.

NOTICE:

Never reinstall the disassembled union bolt to the engine.




Hide 11201 3.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A289512E02
1.75,0.104 1.875,0.104 1.875,0.104 2.271,0.271 false 2.198,0.417 1.781,0.417 false 1.542,0 1.76,0.198 0.219,0.198 10 false *1 1.563,0.323 1.802,0.521 0.24,0.198 10 false *2

Install 4 new No. 3 cylinder head cover gaskets to the cylinder head cover in the directions shown in the illustration.

Text in Illustration
*1 No. 3 Cylinder Head Cover Gasket
*2 Cylinder Head Cover

NOTICE:
·

Do not install the No. 3 cylinder head cover gaskets at an angle.

·

Check that there is no foreign matter at the installation location of the No. 3 cylinder head cover gaskets.




b.

Remove any old seal packing (FIPG material) from the cylinder head.


c.
A384527E01
1.177,0.865 2.583,0.615 false 1.198,0.615 2.854,0.615 false 1.208,1 2.583,0.625 false 1.198,1.448 2.604,0.625 false 2.885,0.51 3.125,0.729 0.24,0.219 10 false *1

Apply seal packing to the specific areas shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Text in Illustration
*1 Seal Packing

NOTICE:
·

Remove any oil from the contact surface.

·

Install the head cover within 3 minutes after applying seal packing.

·

Do not start the engine for at least 2 hours after installing the seal packing.




d.

Install a new cylinder head cover gasket and the cylinder head cover with the 10 bolts and 2 nuts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


e.

Install 4 new nozzle holder seals.


Hide 11202D 4.INSTALL NO. 2 CYLINDER HEAD COVER SUB-ASSEMBLY

a.
U169090E02
0.635,0.198 0.833,0.406 0.198,0.208 10 false A 1.75,1.448 1.906,1.625 0.156,0.177 10 false B 0.594,1.74 0.781,1.927 0.188,0.188 10 false A 3.167,1.719 3.333,1.896 0.167,0.177 10 false B

Install the No. 2 cylinder head cover with the 4 bolts.

Torque:
for bolt A : 18 N*m (184 kgf*cm, 13 ft.*lbf)
for bolt B : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Attach the 2 wire harness clamps and connect the wire harness to the No. 2 cylinder head cover.


c.

Connect the 4 injector connectors.


Hide 23770 6.INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 23704 8.INSTALL NO. 4 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
·

When replacing an injector, it is necessary to replace the 4 injection pipes with new ones.

·

Keep the joints of the injection pipe clean.



a.
A152275

Temporarily install the No. 4 injection pipe with the union nuts.


b.

Install the bolt.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

NOTICE:
·

If an injection pipe clamp is removed from the No. 4 injection pipe, replace the injection clamp with a new one.

·

Make sure that the inner-rubbers of the injection pipe fit inside the clamps.

·

When installing the pipe, check that the inner-rubbers and the clamps are in their proper positions.




c.
A224500E01
0.067,0.045 0.257,0.199 0.189,0.154 10 *a 0.067,2.237 0.257,2.391 0.189,0.154 10 *b

Using a 17 mm union nut wrench, tighten the injection pipe union nut on the common rail side.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)

Text in Illustration
*a Common Rail Side
*b Injector Side

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



d.

Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the injector side.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 17118 9.INSTALL MANIFOLD STAY WITH VACUUM SWITCHING VALVE

Hide 26100G 10.INSTALL INTAKE AIR CONNECTOR WITH DIESEL THROTTLE BODY ASSEMBLY (w/o EGR System)

Hide 17871A 12.INSTALL AIR CONNECTOR STAY (w/o EGR System)

Hide 23701 13.INSTALL NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY (w/o EGR System)

NOTICE:
·

When replacing an injector, it is necessary to replace the 4 injection pipes with new ones.

·

Keep the joints of the injection pipe clean.



a.

Temporarily install the No. 1, No. 2 and No. 3 injection pipes with the union nuts.


b.
A223288E01
1.899,0.489 2.091,0.638 0.192,0.149 10 *1 1.874,0.578 1.788,0.578 1.788,0.578 1.582,1.059 false

Install the No. 2 and No. 3 injection pipe clamps with the 2 bolts and 2 nuts as shown in the illustration.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

Text in Illustration
*1 No. 2 Injection Pipe

HINT:

If the painted mark on the No. 2 injection pipe has disappeared, use the illustration as a reference to install the clamps.



c.
A224501E01
0.059,0.029 0.256,0.184 0.198,0.154 10 *a 0.059,2.728 0.256,2.883 0.198,0.154 10 *b

Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the common rail side.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)

Text in Illustration
*a Common Rail Side
*b Injector Side

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



d.

Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the injector side.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 22267A 14.INSTALL THROTTLE BODY BRACKET (w/o EGR System)

Hide 17113E 15.INSTALL NO. 1 INTAKE PIPE (w/o EGR System)

Hide 25709E 16.CONNECT NO. 4 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/o EGR System)

Hide 87245A 17.CONNECT INLET HEATER WATER HOSE (w/o EGR System)

Hide 25800 18.INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System)

a.

Install the electric EGR control valve assembly (See page Engine / Hybrid System>1KD-FTV (EMISSION CONTROL)>EGR VALVE>INSTALLATION).


Hide 19.PERFORM REGISTRATION

a.

Perform registration of the injector compensation code (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).


b.

Perform registration of pilot quantity learning (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).


Hide 20.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 21.ADD ENGINE COOLANT (w/ EGR System with EGR Cooler)

Hide 23.INSPECT FOR COOLANT LEAK (w/ EGR System with EGR Cooler)