Home › Engine / Hybrid System › 1KD-FTV (ENGINE MECHANICAL) › CAMSHAFT › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053664 1KD-FTV ENGINE MECHANICAL _0260510 CAMSHAFT A

1KD-FTV ENGINE MECHANICAL  CAMSHAFT  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.



PROCEDURE

Hide 13511 1.INSTALL CAMSHAFT

a.
G036616E02
0.573,1.635 1.177,1.792 1.177,1.792 1.25,1.792 false 0.125,1.156 0.458,1.344 0.333,0.188 10 false 90° 1.271,1.708 1.448,1.865 0.177,0.156 10 false *1

Using the crankshaft pulley bolt, set the No. 1 cylinder to 90° BTDC/compression.

Text in Illustration
*1 Key

HINT:

Set the No. 1 cylinder to 90° BTDC/compression to prevent the top of the piston from hitting against the valve head.



b.
A060149E04
0.365,0.542 1.021,0.344 1.021,0.344 1.125,0.344 false 0.344,0.021 0.531,0.188 0.188,0.167 10 false *a 1.146,0.26 1.323,0.417 0.177,0.156 10 false *1

Install the camshaft.

i.

Apply MP grease to the thrust portion of the camshaft.


ii.

Place the camshaft on the cylinder head with the key groove facing upward.

Text in Illustration
*1 Key Groove
*a Upward


iii.
A060150

Align the timing marks (1 dot mark) of the camshaft drive and driven main gears, and set the No. 2 camshaft in place.



c.

Remove any old seal packing (FIPG material) from the camshaft bearing cap.


d.
A060283E05
0.906,1.396 0.906,1.719 false 1.625,0.833 1.281,0.406 1.281,0.406 1.198,0.406 false 2.802,0.833 2.458,0.406 2.458,0.406 2.375,0.406 false 0.813,1.74 1,1.906 0.188,0.167 10 false *2 2.625,0.104 3.292,0.458 0.667,0.354 10 false 8 mm (0.315 in.) 0.99,0.323 1.177,0.49 0.188,0.167 10 false *1 2.177,0.323 2.365,0.49 0.188,0.167 10 false *1

Apply seal packing to the specified areas shown in the illustration.

Text in Illustration
*1 Seal Packing
*2 Oil Passage

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

4 mm (0.157 in.)


NOTICE:
·

Do not allow seal packing to contact the oil passage of the bearing cap.

·

After applying seal packing, install the camshaft bearing caps within 3 minutes and tighten the bolts within 15 minutes.

·

Do not start the engine for at least 2 hours after installation.



i.
A060146

Install the 5 bearing caps to their proper locations.


ii.
A060147E05
1.729,1.031 1.885,1.198 0.156,0.167 10 true 9 1.885,0.563 2.042,0.729 0.156,0.167 10 false 1 1.698,0.354 1.854,0.521 0.156,0.167 10 false 2 2.135,0.74 2.25,0.896 0.115,0.156 10 true 3 2.24,0.354 2.354,0.521 0.115,0.167 10 true 4 1.292,0.667 1.448,0.833 0.156,0.167 10 false 8 1.469,0.813 1.625,0.979 0.156,0.167 10 true 7 2.49,0.51 2.604,0.677 0.115,0.167 10 true 6 2.073,0.177 2.229,0.344 0.156,0.167 10 false 5 2.781,0.177 3.01,0.344 0.229,0.167 10 false 10 2.563,0.052 2.792,0.219 0.229,0.167 10 false 11 3.042,0.375 3.271,0.542 0.229,0.167 10 false 12 0.875,1.135 1.104,1.302 0.229,0.167 10 true 13 0.615,0.958 0.844,1.125 0.229,0.167 10 false 14 1.073,1.354 1.302,1.521 0.229,0.167 10 true 15

Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.


iii.

Install and uniformly tighten the 15 bearing cap bolts in several passes in the sequence shown in the illustration.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)



e.
A060145E02
1.854,0.771 1.063,0.771 false 0.719,0.688 1.052,0.854 0.333,0.167 10 false SST

Install a new camshaft oil seal.

i.

Apply MP grease to the lip of a new oil seal.


ii.

Using SST and a hammer, tap in the oil seal until its surface is flush with the surfaces of the camshaft bearing cap and cylinder head.

SST
09608-06041  



Hide 13505 4.INSTALL NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

Hide 11202D 15.INSTALL NO. 2 CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 16.INSTALL WIRE HARNESS

Hide 23770 17.INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 23704 18.INSTALL NO. 4 INJECTION PIPE SUB-ASSEMBLY

Hide 17118 19.INSTALL MANIFOLD STAY WITH VACUUM SWITCHING VALVE

Hide 26100G 20.INSTALL INTAKE AIR CONNECTOR WITH DIESEL THROTTLE BODY ASSEMBLY (w/o EGR System)

Hide 17871A 22.INSTALL AIR CONNECTOR STAY (w/o EGR System)

Hide 23.INSTALL INJECTION PIPE (w/o EGR System)

Hide 22267A 24.INSTALL THROTTLE BODY BRACKET (w/o EGR System)

Hide 25630 25.INSTALL NO. 2 EGR VALVE ASSEMBLY (w/ EGR System with EGR Cooler)

Hide 25601 26.INSTALL EGR COOLER WITH PIPE (w/ EGR System with EGR Cooler)

Hide 25800 27.TEMPORARILY INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System with EGR Cooler)

Hide 25800 28.TIGHTEN ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System with EGR Cooler)

Hide 25601 29.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY (w/ EGR System without EGR Cooler)

Hide 25800 30.TEMPORARILY INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System without EGR Cooler)

Hide 25800 31.TIGHTEN ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System without EGR Cooler)

Hide 17871A 32.INSTALL AIR CONNECTOR STAY (w/ EGR System)

Hide 33.INSTALL ELECTRIC VACUUM REGULATING VALVE ASSEMBLY (w/ EGR System)

Hide 25625 34.INSTALL EGR VALVE BRACKET (w/ EGR System)

Hide 16281 38.CONNECT NO. 4 WATER BY-PASS HOSE (w/ EGR System with EGR Cooler)

Hide 16267 39.CONNECT NO. 3 WATER BY-PASS HOSE (w/ EGR System with EGR Cooler)

Hide 26100G 40.INSTALL DIESEL THROTTLE BODY ASSEMBLY (w/ EGR System)

Hide 25709E 42.CONNECT NO. 4 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

Hide 55781E 44.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 45.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 51405A 51.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY