Home › Engine / Hybrid System › 1GD-FTV (FUEL) › FUEL SUPPLY PUMP › 2015.06–2018.06
RM27T0E _51 Engine / Hybrid System _053670 1GD-FTV FUEL _0260591 FUEL SUPPLY PUMP A

1GD-FTV FUEL  FUEL SUPPLY PUMP  INSTALLATION  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe subassembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


Supply pump assembly Fuel inlet pipe sub-assembly
·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.

·

Make sure foreign matter does not enter the fuel path.



Hide 22100 2.INSTALL SUPPLY PUMP ASSEMBLY

NOTICE:
A354097

·

Do not hold the supply pump assembly by the parts indicated by the arrows in the illustration.

·

With SST set, do not turn the crankshaft more than a half rotation.



a.

Apply a light coat of engine oil to a new O-ring.


b.

Install the O-ring to the supply pump assembly.


c.
A347065E02
0.573,1.177 1.427,1.177 true 0.344,1.063 0.583,1.313 0.24,0.25 10 true *a

U169470E02
1.813,1.073 2.448,1.073 true 2.344,2.792 2.219,2.792 false 2.219,2.802 2.146,3.292 false 2.49,0.969 2.729,1.188 0.24,0.219 10 false *a 1.198,2.177 1.448,2.417 0.25,0.24 10 false *b 2.375,2.688 2.615,2.927 0.24,0.24 10 false *a 3.01,3.385 3.292,3.573 0.281,0.188 10 false 6°

To insert the supply pump assembly shaft in the supply pump shaft sprocket, it may be necessary to turn the supply pump assembly several degrees and the groove in the supply pump assembly shaft are aligned.

Text in Illustration
*a Groove

HINT:

When installing a new supply pump assembly, adjust the supply pump assembly injection pump drive shaft key assignment by turning the supply pump assembly shown in the illustration.


Text in Illustration
*a Supply Pump Shaft Key
*b Upper Side


d.
A347066E01
1.656,1.75 2.125,1.75 false 1.156,2 1.927,2 1.927,2 1.927,1.75 false 2.417,0.729 2.625,1.094 2.625,1.094 2.792,1.094 true 0.552,1.948 0.781,2.167 0.229,0.219 10 true *a 2.188,1.667 2.833,1.865 0.646,0.198 10 true SST 2.854,1.01 3.25,1.24 0.396,0.229 10 true SST

Using SST, tighten clockwise direction the supply pump assembly, and then temporarily install the 3 fuel supply pump fixing nuts.

SST
09213-58014  (91551-80840)
09330-00021  
09241-11010  

Text in Illustration
*a Hold
V100135

Turn


e.
A344940

Using SST, tighten and insert the supply pump assembly up to the position shown in the illustration and tighten the 3 fuel supply pump fixing nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

HINT:

After tightening the part with SST, a gap of 2 to 3 mm in area A shown in the illustration is normal.



f.

Install the No. 1 fuel pump bracket with the 2 bolts to the supply pump assembly and cylinder block sub-assembly.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


g.

Remove SST and the 3 set bolts.


h.
A347061E02
0.906,1.698 0.969,1.302 0.969,1.302 0.563,1.74 true 1.542,2.063 0.958,2.063 false 1.573,1.958 1.802,2.156 0.229,0.198 10 false *a 1.042,1.188 1.375,1.365 0.333,0.177 10 true SST

Using SST, hold the crankshaft pulley subassembly and tighten the set nut.

SST
09213-58014  (91551-80840)
09330-00021  

Torque:
137 N*m (1397 kgf*cm, 101 ft.*lbf)

Text in Illustration
*a Hold
V100135

Turn


Hide 11324 3.INSTALL TIMING CHAIN COVER PLATE

a.

Install the timing chain cover plate and new gasket with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 4.INSTALL FUEL PUMP MOTOR WIRE

a.

Attach the clamp and install the fuel pump motor wire.


b.

Connect the fuel pump motor wire connector.


Hide 22803 5.INSTALL FUEL INJECTION PUMP COVER SUB-ASSEMBLY

a.

Install the fuel injection pump cover sub-assembly to the supply pump assembly.


Hide 23271H 6.INSTALL NO. 1 FUEL HOSE

a.

Install the No. 1 fuel hose to the supply pump assembly and No. 2 fuel pipe, and slide the 2 clamps to secure it.


Hide 23273C 7.INSTALL NO. 2 FUEL HOSE

a.

Install the No. 2 fuel hose to the supply pump assembly and No. 3 nozzle leakage pipe assembly, and slide the 2 clamps to secure it.


Hide 16620 8.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

Hide 82123 9.CONNECT NO. 3 ENGINE WIRE (for Cold Area Specification Vehicles)

Hide 16470 11.INSTALL RADIATOR RESERVOIR ASSEMBLY

Hide 16.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

(See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION)


Hide 51405A 19.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY