16561
1.INSTALL NO. 1 RADIATOR TO SUPPORT SEAL
Install the No. 1 radiator to support seal to the radiator assembly as shown in the illustration.
16562
2.INSTALL NO. 2 RADIATOR TO SUPPORT SEAL
Install the No. 2 radiator to support seal to the radiator assembly as shown in the illustration.
16534
3.INSTALL NO. 2 RADIATOR SUPPORT
Install the 2 No. 2 radiator supports and 2 No. 1 radiator support bushes as shown in the illustration.
16533B
4.INSTALL NO. 1 RADIATOR SUPPORT
Install the 2 No. 1 radiator supports and 2 No. 1 radiator support bushes as shown in the illustration.
16400
5.INSTALL RADIATOR ASSEMBLY
Insert the No. 1 radiator support hooks into the radiator support holes.
Install the radiator assembly with the 4 bolts.
32942A
6.CONNECT OIL COOLER OUTLET HOSE (for Automatic Transmission)
Connect the oil cooler outlet hose to the radiator assembly, and slide the hose clamp to secure the hose.
| *a | Upper |
| *b | LH Side |
| *c | Paint Mark |
Make sure the direction of the hose clamp is as shown in the illustration.
32941
7.CONNECT OIL COOLER INLET HOSE (for Automatic Transmission)
Connect the oil cooler inlet hose to the radiator assembly, and slide the hose clamp to secure the hose.
16572D
8.CONNECT NO. 2 RADIATOR HOSE
Connect the No. 2 radiator hose to the radiator assembly, and slide the hose clamp to secure the hose.
| *a | Upper |
| *b | LH Side |
| *c | Paint Mark |
Make sure the direction of the hose clamp is as shown in the illustration.
16571C
9.CONNECT NO. 1 RADIATOR HOSE
Connect the No. 1 radiator hose to the radiator assembly, and slide the hose clamp to secure the hose.
| *a | Upper |
| *b | RH Side |
| *c | Paint Mark |
Make sure the direction of the hose clamp is as shown in the illustration.
16711
10.INSTALL FAN SHROUD
Install the fan pulley to the engine water pump assembly.
Place the shroud together with the coupling fan between the radiator assembly and engine.
Be careful not to damage the radiator core.
Temporarily install the fluid coupling fan to the engine water pump assembly with the 4 nuts. Tighten the nuts as much as possible by hand.
Attach the claws of the shroud to the radiator assembly as shown in the illustration.
Install the fan shroud with the 2 bolts.
Install the fan and generator V-belt (See page Engine / Hybrid System>2TR-FE (ENGINE MECHANICAL)>DRIVE BELT>INSTALLATION).
Tighten the 4 nuts of the fluid coupling fan.
Attach the claw to close the flexible hose clamp as shown in the illustration.
16470
11.INSTALL RADIATOR RESERVOIR
Install the radiator reservoir with the 3 bolts.
Connect the reservoir hose to the radiator assembly.
53294C
12.INSTALL RADIATOR SIDE DEFLECTOR LH
Attach the 3 claws.
Install the radiator side deflector LH with the clip.
53293C
13.INSTALL RADIATOR SIDE DEFLECTOR RH
Attach the 3 claws.
Install the radiator side deflector RH with the clip.
52521
14.INSTALL UPPER FRONT BUMPER RETAINER
Install the upper front bumper retainer with the 3 bolts.
52119A
15.INSTALL FRONT BUMPER COVER
16.ADD ENGINE COOLANT
17.INSPECT FOR COOLANT LEAK
51405A
18.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
52129B
19.INSTALL FRONT BUMPER COVER LOWER
53292A
20.INSTALL UPPER RADIATOR SUPPORT SEAL