1. PRECAUTION (for Cold Area Specification Vehicles)
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See pageGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for Cold Area Specification Vehicles)
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
53292A
3.REMOVE UPPER RADIATOR SUPPORT SEAL
Remove the 13 clips and upper radiator support seal.
51405A
4.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
5.DRAIN ENGINE COOLANT
82123
6.REMOVE NO. 3 ENGINE WIRE (for Cold Area Specification Vehicles)
Disconnect 2 cables from 2 positive battery terminals.
Detach the 3 wire harness clamps to disconnect the No. 3 engine wire from the fan shroud.
16571C
7.REMOVE NO. 1 RADIATOR HOSE
Slide the 2 hose clamps and remove the No. 1 radiator hose.
17342F
8.REMOVE NO. 2 INTERCOOLER AIR HOSE
16572D
9.REMOVE NO. 2 RADIATOR HOSE
Slide the 2 hose clamps and remove the No. 2 radiator hose.
17341K
10.REMOVE INTERCOOLER AIR HOSE
Loosen the 2 hose bands and remove the intercooler air hose.
16470
11.REMOVE RADIATOR RESERVOIR ASSEMBLY
Detach the 2 clamps to disconnect the No. 2 water by-pass hose from the fan shroud.
Slide the hose clamp and disconnect the No. 2 water by-pass hose from the water inlet.
Slide the hose clamp and disconnect the No. 1 water by-pass hose from the radiator assembly.
Detach the 2 clamps to disconnect the No. 1 water by-pass hose from the fan shroud.
Remove the 3 bolts and radiator reservoir assembly.
12.DISCONNECT OIL COOLER HOSE (for Automatic Transmission)
Remove the bolt and detach the 2 clamps to disconnect the oil cooler hose from the fan shroud.
Slide the 2 hose clamps and disconnect the oil cooler hose from radiator assembly.
88359
13.REMOVE VISCOUS HEATER V BELT (w/ Viscous Heater)
16711
14.REMOVE FAN SHROUD
Loosen the 4 nuts holding the fan with fluid coupling assembly.
Remove the fan and generator V belt (See page Engine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>DRIVE BELT>REMOVAL).
Remove the 2 bolts holding the fan shroud.
Slide the fan shroud in upper side to detach the guide and remove the fan shroud together with the fan with fluid coupling assembly.
Be careful not to damage the radiator core.
Remove the fan pulley.
52129B
15.REMOVE FRONT BUMPER LOWER COVER
52119A
16.REMOVE FRONT BUMPER COVER
52521
17.REMOVE FRONT BUMPER UPPER RETAINER
Remove the 3 bolts and front bumper upper retainer.
53293C
18.REMOVE RADIATOR SIDE DEFLECTOR RH
Detach the 3 claws and remove the clip and radiator side deflector RH.
53294C
19.REMOVE RADIATOR SIDE DEFLECTOR LH
Detach the 3 claws and remove the clip and radiator side deflector LH.
16400
20.REMOVE RADIATOR ASSEMBLY
Remove the 4 bolts and radiator assembly.
16563
21.REMOVE NO. 3 RADIATOR TO SUPPORT SEAL
Remove the No. 3 radiator to support seal from the No. 1 radiator air guide.
16593
22.REMOVE NO. 1 RADIATOR AIR GUIDE
Remove the 2 bolts and No. 1 radiator air guide.
16562
23.REMOVE NO. 2 RADIATOR TO SUPPORT SEAL
17940D
24.REMOVE INTERCOOLER ASSEMBLY
12209F
25.REMOVE OIL RETURN PIPE SUB-ASSEMBLY
Detach the 2 clamps to remove the oil return pipe sub-assembly from the radiator assembly.
16400S
26.REMOVE RADIATOR COLLAR
Remove the 4 radiator collar from the radiator assembly.
16548
27.REMOVE NO. 2 RADIATOR SUPPORT BUSH
Remove the 2 No. 2 radiator support bushes from the radiator assembly.
16547
28.REMOVE NO. 1 RADIATOR SUPPORT BUSH
Remove the 6 No. 1 radiator support bushes from the radiator assembly.