Home › Engine / Hybrid System › 1GD-FTV (ENGINE MECHANICAL) › ENGINE ASSEMBLY › 2015.06–2018.06
RM27T0E _51 Engine / Hybrid System _053665 1GD-FTV ENGINE MECHANICAL _0260529 ENGINE ASSEMBLY A

1GD-FTV ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 53301 3.REMOVE HOOD SUB-ASSEMBLY

a.

Disconnect the washer nozzle hose.


b.
A354930

Remove the 8 bolts and hood sub-assembly.

NOTICE:

If the hood support is detached from the ball joint, it become non-reusable. Therefore, do not detach the hood support from the ball joint unless replacing it.



Hide 55781E 4.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 52129B 5.REMOVE FRONT BUMPER LOWER COVER

a.

Remove the clip, 5 bolts and front bumper lower cover.


Hide 51405A 6.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

a.
A224743

Remove the 4 bolts and No. 1 engine under cover sub-assembly.


Hide 51495 7.REMOVE TRANSMISSION UNDER COVER

a.

Remove the 2 bolts and transmission under cover.


Hide 51450 8.REMOVE REAR ENGINE UNDER COVER ASSEMBLY

a.

Remove the 4 bolts and rear engine under cover assembly.


Hide 11.DRAIN MANUAL TRANSMISSION OIL (for Manual Transmission)

Hide 12.DRAIN AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)

Hide 16400 13.REMOVE RADIATOR ASSEMBLY

Hide 82121 14.DISCONNECT ENGINE WIRE


b.
A355464

Detach the clamp and disconnect the engine wire from the bracket.


c.
A225401E07
2.042,0.042 2.25,0.229 0.208,0.188 10 true *B 0.083,0.052 0.292,0.24 0.208,0.188 10 true *A

Detach the grommet from the wire harness support.

Text in Illustration
*A for LHD
*B for RHD


d.
A225402E03
0.031,0 0.265,0.188 0.235,0.188 10 *A 1.83,0 2.064,0.188 0.235,0.188 10 *B

Detach the 4 claws and remove the wire harness support from the vehicle, and then pull out the ECM connector to remove it from the vehicle.

Text in Illustration
*A for LHD
*B for RHD


Hide 12601B 15.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 17801 17.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 77820 21.DISCONNECT UREA TANK FILLER PIPE ASSEMBLY (w/ Urea SCR System)

Hide 44306 22.DISCONNECT VANE PUMP OIL RESERVOIR SUB-ASSEMBLY

Hide 23271H 23.DISCONNECT NO. 1 FUEL HOSE

a.
A355475

Disconnect the clamp from the No. 1 fuel hose.


b.

Slide the clamp and disconnect the No. 1 fuel hose from the No. 2 fuel pipe.


Hide 23273H 24.DISCONNECT NO. 2 FUEL HOSE

a.
A355476

Disconnect the 2 clamps from the No. 2 fuel hose.


b.

Slide the clamp and disconnect the No. 2 fuel hose from the No. 3 nozzle leakage pipe.


Hide 82121 25.DISCONNECT ENGINE WIRE

a.
A355477

Detach the 3 claws and remove the No. 1 relay block cover upper from the engine room relay block.


b.
A355478

Remove the nut and detach 2 claws.


c.
A355480

Remove the bolt.


d.

Detach the clamp and disconnect the No. 2 engine wire.


e.
A355481

Remove the nut and disconnect the engine room main wire from the battery.


Hide 74481 26.REMOVE BATTERY HOLD DOWN CLAMP

a.

Loosen the 2 nuts and remove the battery hold down clamp from the body.


Hide 28800 27.REMOVE BATTERY

Hide 74431 28.REMOVE BATTERY TRAY

Hide 44310 30.DISCONNECT VANE PUMP ASSEMBLY

a.
A355483

Disconnect the 2 connectors from the vane pump assembly.


b.
A355484

Remove the 2 bolt and disconnect the vane pump assembly from the generator bracket.


Hide 88320 32.DISCONNECT COOLER COMPRESSOR ASSEMBLY

a.
A355486

Disconnect the connector from the cooler compressor assembly.


b.

Remove the 3 bolts and nut.


c.
A355487

Using an E8 "TORX" socket wrench, remove the stud bolt and disconnect the cooler compressor assembly from the compressor mounting bracket.


Hide 87209B 33.REMOVE WATER HOSE SUB-ASSEMBLY B (w/ Viscous Heater)

a.
A346693

Remove the bolt and disconnect the water hose sub-assembly B from the water inlet.


b.
A346692

Slide the 4 clamps and remove the water hose sub-assembly B from the No. 2 water pipe and water outlet sub-assembly.


Hide 87120G 34.REMOVE VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY (w/ Viscous Heater)

a.

Disconnect the connector from the viscous heater with magnet clutch assembly.


b.
A358233

Remove the 2 bolts and viscous heater with magnet clutch assembly from No. 1 viscous heater bracket.


Hide 17410 35.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 33030 38.REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY (for Manual Transmission)

Hide 32101A 39.REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT (for Automatic Transmission)

Hide 35000 40.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)

Hide 31210 41.REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)

Hide 31250 42.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)

Hide 13405 43.REMOVE FLYWHEEL SUB-ASSEMBLY

a.
A346691

w/ Viscous Heater:

Remove the 4 bolts, viscous heater crankshaft pulley and crankshaft pulley cover from the crankshaft pulley.


b.
A343925

w/o Viscous Heater:

Remove the 4 bolts and crankshaft pulley cover from the crankshaft pulley.


c.
A349457E01
2.019,0.794 2.5,1.123 2.5,1.123 2.918,1.123 false 1.194,0.9 0.81,1.283 0.81,1.283 0.5,1.283 false 2.947,1.033 3.234,1.214 0.287,0.181 10 SST 0.145,1.199 0.432,1.380 0.287,0.181 10 SST

Using SST, hold the crankshaft pulley.

SST
09213-58014  
09330-00021  


d.
A344483

for Manual Transmission:

Remove the 8 bolts and flywheel sub-assembly from the crankshaft.


e.
A344484

for Automatic Transmission:

Remove the 8 bolts, rear drive plate spacer, pump impeller drive plate and flywheel sub-assembly from the crankshaft.


Hide 11355 44.REMOVE REAR END PLATE

a.
A340241

Remove the bolt and rear end plate from the cylinder block sub-assembly.


Hide 45.INSTALL ENGINE HANGER

a.
A355488E01
0.443,0.879 0.755,0.567 0.755,0.567 0.883,0.567 false 2.487,0.405 2.799,0.093 2.799,0.093 2.927,0.093 false 0.912,0.478 1.068,0.660 0.156,0.181 10 *1 2.958,0 3.113,0.181 0.156,0.181 10 *2

Install the No. 1 engine hanger upper and No. 2 engine hanger with the 3 bolts as shown in the illustration.

Torque:
for No. 1 engine hanger upper : 29 N*m (296 kgf*cm, 21 ft.*lbf)
for No. 2 engine hanger : 26 N*m (265 kgf*cm, 19 ft.*lbf)

HINT:
No. 1 Engine Hanger Upper 12284-11010
No. 2 Engine Hanger 12282-11080
Bolt 91671-80835 or 90119-08474 and 91552-81025


Text in Illustration
*1 No. 1 Engine Hanger Upper
*2 No. 2 Engine Hanger


Hide 46.REMOVE ENGINE ASSEMBLY

a.

Attach an engine sling device and hang the engine assembly with a chain block.


b.
A355489

Remove the 4 bolts and 4 nuts from the body.


c.

Lift the engine assembly out from the vehicle slowly and carefully.

NOTICE:
·

Make sure that the engine assembly is clear of all wiring and hoses.

·

While lowering the engine assembly from the vehicle, do not allow it to contact the vehicle.




Hide 47.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine assembly while it is suspended, as doing so is dangerous.



a.

Install the engine assembly to engine stand with the bolts.


b.

Remove the 3 bolts, No. 1 engine hanger upper and No. 2 engine hanger.


Hide 82121 48.REMOVE ENGINE WIRE

a.

Remove the engine wire from the engine assembly.


Hide 12361 49.REMOVE FRONT ENGINE MOUNTING INSULATOR (for LH Side)

a.
A355490

Disconnect the vacuum hose from the front engine mounting insulator.


b.

Remove the nut and front engine mounting insulator from the front engine mounting bracket.