Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053696 CRUISE CONTROL _0260748 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Distance Control Switch Circuit  


DESCRIPTION

The distance control switch sets the vehicle-to-vehicle distance setting. The distance control switch is installed in the steering pad switch. The vehicle-to-vehicle distance setting can be changed by operating the distance control switch in the steering pad switch while the dynamic radar cruise control system is in operation.

WIRING DIAGRAM

E178428E13
5.729,2.385 6.417,2.583 0.688,0.198 10 false G119 5.729,2.542 7.083,2.75 1.354,0.208 10 false Driving Support ECU 5.583,0.906 5.698,1.104 0.115,0.198 10 false 7 5.813,1.021 6.396,1.354 0.583,0.333 10 false MODE 4.688,0.823 4.99,1.063 0.302,0.24 10 false 11 4.25,0.917 4.656,1.208 0.406,0.292 10 false DIST 4.656,1.021 5,1.24 0.344,0.219 10 false G40 4.656,1.771 5.083,1.969 0.427,0.198 10 false G40 4.75,1.583 4.917,1.74 0.167,0.156 10 false 2 3.469,1.021 3.76,1.24 0.292,0.219 10 false z8 3.49,0.813 3.656,0.969 0.167,0.156 10 false 4 3.458,1.781 3.75,2.073 0.292,0.292 10 false z8 3.5,1.594 3.667,1.833 0.167,0.24 10 false 6 3.75,0.917 4.26,1.208 0.51,0.292 10 false DIST 3.76,1.667 4.26,1.896 0.5,0.229 10 false ECC 3.021,0.917 3.438,1.146 0.417,0.229 10 false DIST 3.021,1.667 3.5,1.948 0.479,0.281 10 false ECC 4.26,1.667 4.729,1.865 0.469,0.198 10 false ECC 3.729,2.323 4.667,2.75 0.938,0.427 10 false Spiral Cable Sub-assembly 0.927,2.354 3.302,2.531 2.375,0.177 10 false Steering Pad Switch Assembly 0.969,1.479 2.583,1.667 1.615,0.188 10 false Distance Control Switch

PROCEDURE

1.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL).


b.
E181977E03
1.726,1.153 2.042,1.295 0.316,0.142 10 ECC 1.894,1.145 1.719,0.875 false 1.215,1.145 1.39,0.723 false 1.428,4.261 1.772,4.403 0.344,0.142 10 DIST 0.813,4.264 1.128,4.406 0.316,0.142 10 ECC 1.625,4.256 1.441,3.796 false 0.999,4.256 1.174,3.922 false 0.999,4.256 1.174,3.922 false 1.02,1.159 1.364,1.301 0.344,0.142 10 DIST

If there are any defects as follows, replace the spiral cable with a new one: scratches, cracks, dents or chips in the connector or spiral cable.


c.

Check the spiral cable.

i.

Set the spiral cable to the center position (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION).


ii.

Rotate the spiral cable 2.5 times clockwise and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable 5 times counterclockwise and measure the resistance according to the value(s) in the table below.

NOTICE:

As the spiral cable may break, do not rotate the spiral cable more than the specified amount.


Standard Resistance:
Tester Connection Condition Specified Condition
4 (DIST) - 11 (DIST) Always Below 1 Ω
6 (ECC) - 2 (ECC)



iii.

Set the spiral cable to the center position and rotate the spiral cable 2.5 times clockwise. Then, while rotating the spiral cable 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (DIST) - 11 (DIST) Always Below 1 Ω
6 (ECC) - 2 (ECC)





OK

2.INSPECT STEERING PAD SWITCH ASSEMBLY (DISTANCE CONTROL SWITCH)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

2.INSPECT STEERING PAD SWITCH ASSEMBLY (DISTANCE CONTROL SWITCH)
a.

Remove the steering pad switch assembly (See page Steering>STEERING COLUMN>STEERING WHEEL>REMOVAL).

E192966E23
4.469,0.823 4.948,0.823 false 4.188,1 4.354,1.313 4.354,1.313 4.479,1.313 false 4.656,2.604 4.906,2.604 false 4.979,0.75 5.323,0.896 0.344,0.146 10 false DIST 4.5,1.25 4.844,1.396 0.344,0.146 10 false ECC 4.938,2.542 5.281,2.688 0.344,0.146 10 false *1

Text in Illustration
*1 Distance Control Switch - -


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 (DIST) - 6 (ECC) Distance control switch on Below 2.5 Ω
Distance control switch off 1 MΩ or higher




OK

3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - DRIVING SUPPORT ECU AND BODY GROUND)

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - DRIVING SUPPORT ECU AND BODY GROUND)
a.

Disconnect the G40 spiral cable connector.


b.

Disconnect the G119 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G40-11 (DIST) - G119-7 (MODE) Always Below 1 Ω
G40-2 (ECC) - Body ground
G40-11 (DIST) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR