Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION ASSEMBLY (for 2TR-FE) › 2015.06–2020.08
RM27T0E _52 Drivetrain _053698 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0260776 AUTOMATIC TRANSMISSION ASSEMBLY(for 2TR-FE) A

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY(for 2TR-FE)  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

The automatic transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 51405A 3.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 51450 4.REMOVE REAR ENGINE UNDER COVER ASSEMBLY

Hide 37140 8.REMOVE FRONT PROPELLER SHAFT ASSEMBLY

Hide 17410 9.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 11354 11.REMOVE FLYWHEEL HOUSING DUST SEAL

a.
C326319

Remove the flywheel housing dust seal from the engine assembly.


Hide 32101A 12.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.
C330316

Turn the crankshaft to gain access to the locations of the 6 drive plate and torque converter assembly setting bolts and remove each bolt while holding the crankshaft pulley bolt with a wrench.

HINT:

There will be one black colored bolt.



Hide 17118 13.REMOVE MANIFOLD STAY

a.

Remove the 3 bolts and manifold stay from the automatic transmission assembly and exhaust manifold.


Hide 33820B 14.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C323981

Remove the clip and nut and disconnect the transmission control cable assembly from the transmission control shaft lever LH and transmission control cable bracket.


Hide 82046A 16.DISCONNECT NO. 1 BODY GROUND WIRE SUB-ASSEMBLY

a.
C330296

Remove the bolt and disconnect the No. 1 body ground wire sub-assembly from the automatic transmission assembly.


Hide 17.DISCONNECT OIL COOLER TUBE

a.
C324534

Disconnect the 2 oil cooler tubes from the automatic transmission assembly.

HINT:

Use a container to catch any ATF.



b.

Remove the bolt and flexible hose clamp.

C330294E02
0.875,1.948 0.802,2.281 0.802,2.281 0.708,2.281 true 0.531,2.208 0.688,2.385 0.156,0.177 10 false *1

Text in Illustration
*1 Flexible Hose Clamp - -


c.

Remove the 2 bolts and disconnect the 2 oil cooler tubes from the engine assembly.


Hide 51225B 18.REMOVE FRONT SUSPENSION MEMBER BRACKET LH AND RH

a.
C330300

Remove the 8 bolts, front suspension member bracket LH and RH from the No. 3 frame crossmember sub-assembly and vehicle body.


Hide 35000 19.SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

a.
C330299

Support the automatic transmission assembly with a transmission jack.

NOTICE:
·

In order to protect the automatic transmission oil pan sub-assembly, place attachments on the transmission jack.

·

Make sure that the attachments and the automatic transmission oil pan sub-assembly are centered on the transmission jack.

·

To prevent the automatic transmission oil pan sub-assembly from deforming, do not place any attachments under the automatic transmission oil pan sub-assembly of the automatic transmission assembly.

·

Secure the automatic transmission assembly to the transmission jack using a belt, etc. to prevent it from falling.




Hide 51203 20.REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.
C330302

Remove the 4 bolts and disconnect the No. 3 frame crossmember sub-assembly from the rear engine mounting insulator.


b.
C213724

Remove the 4 bolts, 4 nuts and No. 3 frame crossmember sub-assembly from the vehicle body.


Hide 12371 21.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

HINT:

It is not necessary to remove the rear engine mounting insulator unless it is being replaced.


a.
C330290

Remove the 4 bolts and rear No. 1 engine mounting insulator from the automatic transmission assembly.


Hide 36478A 22.REMOVE TRANSMISSION BREATHER BRACKET

a.
C330298

Tilt down the automatic transmission assembly.

NOTICE:

Make sure that the cooling fan and fan shroud do not contact the engine assembly when tilting the automatic transmission assembly.



b.
C332140

Disconnect the 3 breather hoses from the transmission breather bracket.


c.
C332141

Remove the bolt and disconnect the transmission breather bracket from the automatic transmission assembly.


d.

Detach the wire harness clamp from the transmission breather bracket.


e.

Remove the 2 clamps from the transmission breather bracket.

HINT:

It is not necessary to remove the transmission clamps they are being replaced.



Hide 23.DISCONNECT WIRE HARNESS

a.
C333124

Disconnect the breather hose from the wire harness.


b.

Disconnect the park/neutral position switch connector, transmission wire connector, 2 speed sensor connectors and transfer connector.

C333308

HINT:

Detach the claw, press down the lever, and then disconnect the transmission wire connector.



c.

Detach the heated oxygen sensor connector from the wire harness clamp bracket.


d.

Remove the 3 bolts and disconnect the wire harness from the automatic transmission assembly.


Hide 35000 24.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

a.
C332142

Disconnect the breather hose from the engine assembly.


b.
C330332

Remove the 7 bolts and automatic transmission assembly from the engine assembly.

NOTICE:

To prevent damage to the 2 knock pins, do not pry between the automatic transmission assembly and engine assembly.



Hide 33823 26.REMOVE TRANSMISSION CONTROL CABLE BRACKET

HINT:

It is not necessary to remove the transmission control cable bracket unless it is being replaced.


a.
C324529

Remove the 2 bolts and transmission control cable bracket from the automatic transmission assembly.


Hide 3516A 27.REMOVE TRANSMISSION OIL PAN HEAT INSULATOR

HINT:

It is not necessary to remove the transmission oil pan heat insulator unless it is being replaced.


a.
C330312

Remove the 3 bolts and transmission oil pan heat insulator from the automatic transmission assembly.


Hide 32000 28.REMOVE TORQUE CONVERTER ASSEMBLY

a.
C324532E02
1.719,0.24 1.125,0.146 1.125,0.146 1.719,0.438 true 0.927,0.021 1.083,0.198 0.156,0.177 10 false *a

Put matchmarks on the automatic transmission case sub-assembly and the torque converter assembly.

Text in Illustration
*a Matchmark


b.

Remove the torque converter assembly from the automatic transmission assembly.

NOTICE:

Remove the torque converter assembly from the input shaft horizontally.



Hide 82715J 29.REMOVE WIRING HARNESS CLAMP BRACKET

HINT:

It is not necessary to remove the wire harness clamp brackets unless they are being replaced.


a.
C330305

Detach the 8 wire harness clamps and 4 wire harness clamp brackets from the wire harness.