Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER ASSEMBLY › 2015.06–2020.08
RM27T0E _52 Drivetrain _053705 AXLE AND DIFFERENTIAL _0260863 FRONT DIFFERENTIAL CARRIER ASSEMBLY A

AXLE AND DIFFERENTIAL  FRONT DIFFERENTIAL CARRIER ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
·

w/ Navigation System (for HDD):

After the engine switch is turned off, the HDD navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the engine switch off, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



Hide 2.REMOVE FRONT WHEELS

Hide 51405A 3.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 4.REMOVE TRANSMISSION UNDER COVER (except 5L-E)

Hide 51450 5.REMOVE REAR ENGINE UNDER COVER ASSEMBLY (except 5L-E)

Hide 37140 7.REMOVE FRONT PROPELLER SHAFT ASSEMBLY

Hide 43420 8.REMOVE FRONT DRIVE SHAFT ASSEMBLY

Hide 48810 9.REMOVE FRONT STABILIZER LINK ASSEMBLY

a.

w/ KDSS:

Remove the stabilizer link (See page Suspension>FRONT SUSPENSION>FRONT STABILIZER BAR (w/ KDSS)>REMOVAL).


b.

w/o KDSS:

Remove the stabilizer link (See page Suspension>FRONT SUSPENSION>FRONT STABILIZER BAR (w/o KDSS)>REMOVAL).


Hide 89543 10.REMOVE FRONT SPEED SENSOR

Hide 45047 11.DISCONNECT TIE ROD END SUB-ASSEMBLY LH

a.

Disconnect the tie rod end sub-assembly (See page Steering>STEERING GEAR / LINKAGE>STEERING GEAR>REMOVAL).


Hide 45046 12.DISCONNECT TIE ROD END SUB-ASSEMBLY RH

a.

Disconnect the tie rod end sub-assembly (See page Steering>STEERING GEAR / LINKAGE>STEERING GEAR>REMOVAL).


Hide 48069 13.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.

Remove the front lower No. 1 suspension arm sub-assembly (See page Suspension>FRONT SUSPENSION>FRONT LOWER SUSPENSION ARM>REMOVAL).


Hide 48068 14.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 41110F 15.REMOVE FRONT DIFFERENTIAL CARRIER ASSEMBLY

C097020E10
1.313,0.188 1.5,0.344 0.188,0.156 10 true *1 1.99,0.188 2.177,0.344 0.188,0.156 10 true *1 1.844,1.49 2.031,1.646 0.188,0.156 10 true *2

a.

Remove the bolt and disconnect the front differential breather tube bracket.


b.

Support the front differential with a jack.


c.

Remove the front No. 1 differential mounting nut.


d.

Remove the 2 front mounting bolts and nut.

Text in Illustration
*1 Mounting Bolt
*2 Mounting Nut


e.

Disconnect the actuator hose and connector.


f.

Lower the jack and remove the front differential.


g.
B084273

Remove the 3 bolts and front No. 1 differential support.


h.
B084274

Remove the 2 bolts and front No. 2 differential support.


i.
B084275

Remove the 2 bolts and front No. 3 differential support.