Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM › 2015.06–2017.08
RM27T0E _53 Suspension _053706 SUSPENSION CONTROL _0260870 AIR SUSPENSION SYSTEM C

SUSPENSION CONTROL  AIR SUSPENSION SYSTEM  C1791/91  Adaptive Variable Suspension (AVS) Switch Circuit (Test Mode DTC)  


DESCRIPTION

The absorber control switch is used to select the damping force mode of the shock absorber.

DTC Code DTC Detection Condition Trouble Area
C1791/91 The absorber control switch signal does not change.
·

Absorber control switch (Center cluster module switch)

·

Harness or connector

·

Suspension control ECU



HINT:

This DTC is stored only during test mode.


WIRING DIAGRAM

C214514E10
5.021,1.958 5.354,2.135 0.333,0.177 10 false A49 5.021,2.115 6.594,2.323 1.573,0.208 10 false Suspension Control ECU 1.583,1.969 1.958,2.156 0.375,0.188 10 false G156 1.594,2.135 3.583,2.563 1.99,0.427 10 false Absorber Control Switch (Center Cluster Module Switch) 3.208,0.75 3.646,0.906 0.438,0.156 10 false ECU2 3.719,0.542 3.948,0.729 0.229,0.188 10 false 8 3.719,1.354 3.885,1.563 0.167,0.208 10 false 9 3.219,1.375 3.635,1.531 0.417,0.156 10 false ECU1 1.385,0.938 1.583,1.135 0.198,0.198 10 false 24 1.656,0.948 1.854,1.125 0.198,0.177 10 false E 5.5,0.625 5.948,0.813 0.448,0.188 10 false TSW2 5.5,1.479 5.958,1.677 0.458,0.198 10 false TSW1 5.188,0.51 5.427,0.698 0.24,0.188 10 false 22 5.177,1.365 5.427,1.542 0.25,0.177 10 false 23 2.25,0.49 2.99,0.667 0.74,0.177 10 false COMFORT 2.292,1.625 2.844,1.844 0.552,0.219 10 false SPORT

CAUTION / NOTICE / HINT

NOTICE:

When replacing the suspension control ECU, perform registration (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>REGISTRATION).


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (DAMPING CONTROL SWITCH)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / Air suspension / Data List.

Air Suspension
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Damping Control Switch Absorber control switch /
NORMAL, COMFORT or SPORT
Indicates current absorber control switch position -


f.

Check that the value displayed on the intelligent tester changes by operating the absorber control switch between COMF, NORMAL and SPORT.

OK:

Absorber control switch value changes.




OK

NG

2.INSPECT CENTER CLUSTER MODULE SWITCH
2.INSPECT CENTER CLUSTER MODULE SWITCH
a.

Turn the ignition switch off.


b.

Remove the absorber control switch (center cluster module switch) (See page Suspension>SUSPENSION CONTROL>ABSORBER CONTROL SWITCH>REMOVAL).


c.
C296052E10
0.792,1.302 0.344,1.479 0.344,1.479 0.344,1.646 false 1.313,0.99 1.208,0.302 1.208,0.302 1.042,0.302 false 1.531,1 2.167,0.26 2.167,0.26 2.323,0.26 false 0.083,0.031 0.26,0.198 0.177,0.167 10 false *a 2.385,0.167 2.865,0.354 0.479,0.188 10 false ECU2 0.313,1.677 0.656,1.844 0.344,0.167 10 false E 0.635,0.219 1.115,0.385 0.479,0.167 10 false ECU1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
24 (E) - 9 (ECU1) SPORT position Below 1 Ω
Normal position 10 kΩ or higher
24 (E) - 8 (ECU2) COMF position Below 1 Ω
Normal position 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Absorber Control Switch (Center Cluster Module Switch))



OK

3.CHECK HARNESS AND CONNECTOR (CENTER CLUSTER MODULE SWITCH - SUSPENSION CONTROL ECU)

NG

REPLACE CENTER CLUSTER MODULE SWITCH

3.CHECK HARNESS AND CONNECTOR (CENTER CLUSTER MODULE SWITCH - SUSPENSION CONTROL ECU)
a.

Disconnect the G156 absorber control switch (center cluster module switch) connector.


b.

Disconnect the A49 suspension control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G156-9 (ECU1) - A49-23 (TSW1) Always Below 1 Ω
G156-8 (ECU2) - A49-22 (TSW2) Always Below 1 Ω
G156-24 (E) - Body ground Always Below 1 Ω
G156-9 (ECU1) or A49-23 (TSW1) - Body ground Always 10 kΩ or higher
G156-8 (ECU2) or A49-22 (TSW2) - Body ground Always 10 kΩ or higher




OK

REPLACE SUSPENSION CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR