Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM › 2015.06–2017.08
RM27T0E _53 Suspension _053706 SUSPENSION CONTROL _0260870 AIR SUSPENSION SYSTEM C

SUSPENSION CONTROL  AIR SUSPENSION SYSTEM  C1792/92  Height Control Switch Circuit (Test Mode DTC)  


DESCRIPTION

The vehicle height can be adjusted by pressing the height control switch.

By pressing the "up" side, vehicle height is raised.

By pressing the "down" side, vehicle height is lowered.

DTC Code DTC Detection Condition Trouble Area
C1792/92 The height control switch signal does not change.
·

Height control switch (Center cluster module switch)

·

Harness or connector

·

Suspension control ECU



HINT:

This DTC is stored only during test mode.


WIRING DIAGRAM

C218601E08
5.208,1.938 6.813,2.125 1.604,0.188 10 false Suspension Control ECU 2.49,1.625 2.896,1.813 0.406,0.188 10 false G156 3.792,1.125 3.927,1.313 0.135,0.188 10 false 7 3.792,0.469 3.927,0.656 0.135,0.188 10 false 6 5.385,1.125 5.594,1.313 0.208,0.188 10 false 14 5.385,0.469 5.594,0.656 0.208,0.188 10 false 15 5.688,1.24 6.167,1.427 0.479,0.188 10 false DNSW 5.688,0.573 6.167,0.76 0.479,0.188 10 false UPSW 2.667,0.792 2.813,0.979 0.146,0.188 10 false E 3.521,0.458 3.708,0.646 0.188,0.188 10 false HI 2.906,0.646 3.229,0.833 0.323,0.188 10 false Up 3.49,1.125 3.708,1.313 0.219,0.188 10 false LO 2.792,1.198 3.198,1.469 0.406,0.271 10 false Down 2.385,0.792 2.615,0.979 0.229,0.188 10 false 24 2.49,1.802 4.313,2.198 1.823,0.396 10 false Height Control Switch (Center Cluster Module Switch) 5.208,1.792 5.51,1.979 0.302,0.188 10 false A49

CAUTION / NOTICE / HINT

NOTICE:

When replacing the suspension control ECU, perform registration (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>REGISTRATION).


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (HEIGHT CONTROL SWITCH)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / Air suspension / Data List.

Air Suspension
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Height Control Switch (UP) Height control switch ("up" side) / ON or OFF ON: Switch is pressed and held
OFF: Switch is not pressed
-
Height Control Switch (DOWN) Height control switch ("down" side) / ON or OFF ON: Switch is pressed and held
OFF: Switch is not pressed
-


f.

Check that the value displayed on the intelligent tester changes by pressing the height control switch "up" side or "down" side.

OK:

Height control switch value changes.




OK

NG

2.INSPECT CENTER CLUSTER MODULE SWITCH
2.INSPECT CENTER CLUSTER MODULE SWITCH
a.

Turn the ignition switch off.


b.

Remove the height control switch (center cluster module switch) (See page Suspension>SUSPENSION CONTROL>HEIGHT CONTROL SWITCH>REMOVAL).


c.
C296052E11
0.792,1.292 0.385,1.521 0.385,1.521 0.385,1.667 false 1.885,1 2.563,0.219 2.563,0.219 2.708,0.219 false 1.646,0.99 0.896,0.229 0.896,0.229 0.729,0.229 false 0.083,0.031 0.26,0.198 0.177,0.167 10 false *a 2.76,0.125 3.24,0.313 0.479,0.188 10 false HI 0.344,1.688 0.688,1.854 0.344,0.167 10 false E 0.521,0.146 0.802,0.313 0.281,0.167 10 false LO

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
7 (LO) - 24 (E) "Down" pressed Below 1 Ω
7 (LO) - 24 (E) "Up" pressed 10 kΩ or higher
6 (HI) - 24 (E) "Down" pressed 10 kΩ or higher
6 (HI) - 24 (E) "Up" pressed Below 1 Ω


Text in Illustration
*a Component without harness connected
(Height Control Switch (Center Cluster Module Switch))



OK

3.CHECK HARNESS AND CONNECTOR (CENTER CLUSTER MODULE SWITCH - SUSPENSION CONTROL ECU)

NG

REPLACE CENTER CLUSTER MODULE SWITCH

3.CHECK HARNESS AND CONNECTOR (CENTER CLUSTER MODULE SWITCH - SUSPENSION CONTROL ECU)
a.

Disconnect the G156 height control switch (center cluster module switch) connector.


b.

Disconnect the A49 suspension control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G156-6 (HI) - A49-15 (UPSW) Always Below 1 Ω
G156-7 (LO) - A49-14 (DNSW) Always Below 1 Ω
G156-24 (E) - Body ground Always Below 1 Ω
G156-6 (HI) or A49-15 (UPSW) - Body ground Always 10 kΩ or higher
G156-7 (LO) or A49-14 (DNSW) - Body ground Always 10 kΩ or higher




OK

REPLACE SUSPENSION CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR