Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM › 2015.06–2017.08
RM27T0E _53 Suspension _053706 SUSPENSION CONTROL _0260870 AIR SUSPENSION SYSTEM C

SUSPENSION CONTROL  AIR SUSPENSION SYSTEM  C1794/94  Height Control OFF Switch Circuit (Test Mode DTC)  


DESCRIPTION

If the height control OFF switch is pressed when the vehicle is stopped with the engine running or the ignition switch ON, vehicle height control is disabled and remains disabled even after the ignition switch is turned off. Pressing the height control OFF switch again with the engine running or the ignition switch ON resumes vehicle height control. If the vehicle speed reaches approximately 30 km/h (19 mph) when vehicle height control is disabled, vehicle height control automatically resumes.

DTC Code DTC Detection Condition Trouble Area
C1794/94 Stored only during test mode.
·

Height control OFF switch (Center cluster module switch)

·

Harness or connector

·

Suspension control ECU



WIRING DIAGRAM

C218604E09
0.938,1.552 1.323,1.719 0.385,0.167 10 false G156 2.365,1 2.542,1.167 0.177,0.167 10 false N 1.052,1 1.302,1.167 0.25,0.167 10 false E 0.792,1 1.021,1.146 0.229,0.146 10 false 24 2.563,1 2.75,1.146 0.188,0.146 10 false 5 5.083,0.969 5.281,1.146 0.198,0.177 10 false 13 5.073,2 5.385,2.156 0.313,0.156 10 false A49 5.375,1.104 5.792,1.271 0.417,0.167 10 false TD 5.073,2.146 6.729,2.292 1.656,0.146 10 false Suspension Control ECU 0.938,1.729 3.083,2.104 2.146,0.375 10 false Height Control OFF Switch (Center Cluster Module Switch)

CAUTION / NOTICE / HINT

NOTICE:

When replacing the suspension control ECU, perform registration (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>REGISTRATION).


PROCEDURE

1.INSPECT CENTER CLUSTER MODULE SWITCH
a.

Remove the height control OFF switch (center cluster module switch) (See page Suspension>SUSPENSION CONTROL>HEIGHT CONTROL OFF SWITCH>REMOVAL).


b.
C296052E12
0.792,1.292 0.375,1.521 0.375,1.521 0.375,1.656 false 2.052,1 2.438,0.229 2.438,0.229 2.573,0.229 false 0.083,0.031 0.26,0.198 0.177,0.167 10 false *a 2.625,0.146 3.104,0.333 0.479,0.188 10 false N 0.333,1.677 0.677,1.844 0.344,0.167 10 false E

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (N) - 24 (E) Height control OFF switch pressed Below 1 Ω
Height control OFF switch not pressed 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Height Control OFF Switch (Center Cluster Module Switch))



OK

2.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - CENTER CLUSTER MODULE SWITCH)

NG

REPLACE CENTER CLUSTER MODULE SWITCH

2.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - CENTER CLUSTER MODULE SWITCH)
a.

Disconnect the A49 suspension control ECU connector.


b.

Disconnect the G156 height control OFF switch (center cluster module switch) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A49-13 (TD) - G156-5 (N) Always Below 1 Ω
A49-13 (TD) or G156-5 (N) - Body ground Always 10 kΩ or higher
G156-24 (E) - Body ground Always Below 1 Ω




OK

REPLACE SUSPENSION CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR