Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260910 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1401  Front Speed Sensor RH Malfunction  C1271  Low Output Signal of Front Speed Sensor RH (Test Mode DTC)  C1272  Low Output Signal of Front Speed Sensor LH (Test Mode DTC)  C1402  Front Speed Sensor LH Malfunction  


DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. These signals are used for brake control.

The speed sensor rotors have rows of alternating N and S magnetic poles and their magnetic fields change when the rotors turn.

Each speed sensor detects that magnetic change and sends a pulse signal to the skid control ECU.

HINT:

When the connectors between the speed sensor and skid control ECU are connected, the following waveform is output.


C173114E12
5.521,1.26 6.229,0.688 6.229,0.688 6.302,0.688 false 6.167,1.271 6.26,0.958 6.26,0.958 6.313,0.958 false 1.896,0.635 2.854,0.823 0.958,0.188 10 false Speed Sensor 1.51,1.333 2,1.49 0.49,0.156 10 false MRE A 1.51,1.625 2,1.781 0.49,0.156 10 false MRE B 2.25,1.458 2.896,1.615 0.646,0.156 10 false Sensor IC 4.01,2.063 4.656,2.25 0.646,0.188 10 false Backward 6.354,0.875 7.135,1.063 0.781,0.188 10 false High Speed 6.354,0.615 7.083,0.802 0.729,0.188 10 false Low Speed 6.698,1.323 7.073,1.469 0.375,0.146 10 false 2.6 V 6.698,1.51 7.073,1.656 0.375,0.146 10 false 1.4 V 6.698,1.75 7.073,1.896 0.375,0.146 10 false 0.7 V 5.417,2.063 5.99,2.208 0.573,0.146 10 false Forward 0.073,2.427 2.698,2.615 2.625,0.188 10 false Speed Sensor Rotor (Bearing Inner Race) 3.24,1.417 3.76,1.563 0.521,0.146 10 false to ECU 3.177,1.083 3.396,1.271 0.219,0.188 10 false (+) 3.177,1.823 3.365,2.01 0.188,0.188 10 false (-) 3.406,0.052 5.094,0.24 1.688,0.188 10 false Waveform (Reference): 3.406,0.333 6.333,0.5 2.927,0.167 10 false Between Speed Sensor (-) and Body Ground

DTC Code DTC Detection Condition Trouble Area
C1401
C1402
One of the following conditions is met:
1.

At a vehicle speed of 10 km/h (6 mph) or more, the output voltage from one of the speed sensors is below that from the other sensors for 15 seconds or more.

2.

At a vehicle speed of less than 10 km/h (6 mph), the output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

3.

At a vehicle speed of 10 km/h (6 mph) or more, the outputs from both front speed sensors are 0 km/h (0 mph) for 15 seconds or more.


·

Front speed sensor RH/LH

·

Front speed sensor rotor RH/LH

·

Sensor installation


C1271
C1272
Stored only during test mode.
·

Front speed sensor RH/LH

·

Front speed sensor rotor RH/LH

·

Sensor installation



HINT:
·

DTC C1401 is for the front speed sensor RH.

·

DTC C1402 is for the front speed sensor LH.



CAUTION / NOTICE / HINT

NOTICE:

Check the speed sensor signal after cleaning or replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE).


PROCEDURE

1.CHECK FRONT SPEED SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.
C144929E49
0.628,2.889 0.910,3.090 0.282,0.201 10 *b 2.658,2.889 2.985,3.090 0.326,0.201 10 *c 1.119,2.636 2.037,2.837 0.918,0.201 10 *a 0.114,0.065 0.349,0.263 0.235,0.198 10 *1 0.708,2.449 0.965,2.759 false 0.965,2.759 1.08,2.759 false

Check the speed sensor installation (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>INSTALLATION).

Text in Illustration
*1 Front Speed Sensor
*a No clearance
*b OK
*c NG

OK:

There is no clearance between the sensor and the front steering knuckle.

The installation bolt is tightened properly.




OK

2.INSPECT FRONT SPEED SENSOR TIP

NG

2.INSPECT FRONT SPEED SENSOR TIP

b.

Check the speed sensor tip.

OK:

No scratches, oil, or foreign matter on the sensor tip.


NOTICE:

If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.




OK

3.INSPECT FRONT SPEED SENSOR ROTOR

NG

CLEAN OR REPLACE FRONT SPEED SENSOR

3.INSPECT FRONT SPEED SENSOR ROTOR
a.

Remove the front axle with ABS rotor bearing assembly (See page Drivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL).


b.

Check the speed sensor rotor.

OK:

No scratches, oil, or foreign matter on the rotors.


HINT:

The front speed sensor rotor is incorporated into the front axle with ABS rotor bearing assembly.

If the front speed sensor rotor needs to be replaced, replace it together with the front axle with ABS rotor bearing assembly.




OK

4.READ VALUE USING INTELLIGENT TESTER (FR/FL WHEEL SPEED)

NG

CLEAN OR REPLACE FRONT SPEED SENSOR ROTOR

4.READ VALUE USING INTELLIGENT TESTER (FR/FL WHEEL SPEED)
a.

Turn the ignition switch off


b.

Connect the intelligent tester to the DLC3.


c.

Start the engine.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Wheel Speed Front speed sensor RH value/ min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) Actual wheel speed No large fluctuations when driving at a constant speed.
FL Wheel Speed Front speed sensor LH value/ min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) Actual wheel speed No large fluctuations when driving at a constant speed.


f.

Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, refer to the reference chart (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK).


OK:

The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).




OK

NG

5.REPLACE FRONT SPEED SENSOR
5.REPLACE FRONT SPEED SENSOR
a.

Turn the ignition switch off.


b.


NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC

b.

Start the engine.


c.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.


d.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B

HINT:

The front speed sensor rotor is incorporated into the front axle with ABS rotor bearing assembly.

If the front speed sensor rotor needs to be replaced, replace it together with the front axle with ABS rotor bearing assembly.




A

END

B

REPLACE FRONT AXLE WITH ABS ROTOR BEARING ASSEMBLY