Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster) › 2015.06–2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260911 VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster)  C0278  Open in ABS Solenoid Relay Circuit  C0279  Short in ABS Solenoid Relay Circuit  


DESCRIPTION

The solenoid relay is built into the master cylinder solenoid.

This relay supplies power to each solenoid. If the initial check is OK, after the ignition switch is turned to ON, the relay turns on.

DTC Code DTC Detection Condition Trouble Area
C0278 Either condition is met:
1.

Both of the following conditions continue for at least 0.2 seconds.

(a)

IG voltage is between 9.5 and 17 V.

(b)

The relay contact is open when the relay is on.


2.

Both of the following conditions continue for at least 0.2 seconds.

(a)

IG voltage is 9.5 V or less when the relay is on.

(b)

The relay contact remains open.



·

ABS NO. 2 fuse

·

Solenoid relay circuit

·

Master cylinder solenoid


C0279 The following condition continues for at least 0.2 seconds.
·

The relay contact is closed immediately after turning the ignition switch to ON when the relay is off.



WIRING DIAGRAM

Refer to DTCs C0226, C0236, C0246, C0256, C1225, C1226, C1227 and C1228 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>C0226).

CAUTION / NOTICE / HINT

NOTICE:
·
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (+BS)
a.

Disconnect the A7 skid control ECU connector.


b.
U148395E01
0.128,0 2.553,0.354 2.426,0.354 10 *a 0.825,1.435 0.825,1.856 false 0.618,1.89 0.969,2.067 0.350,0.177 10 +BS 1.635,0.424 1.819,0.554 0.184,0.130 9 A7

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A7-31 (+BS) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)



OK

2.CHECK HARNESS AND CONNECTOR (GND1, GND2, AND GND3 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (GND1, GND2, AND GND3 TERMINAL)
a.

Disconnect the A7 and A8 skid control ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A7-1 (GND1) - Body ground Always Below 1 Ω
A7-32 (GND2) - Body ground Always Below 1 Ω
A8-4 (GND3) - Body ground Always Below 1 Ω




OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.RECONFIRM DTC
HINT:

These codes are stored when a problem is detected in the master cylinder solenoid.

The solenoid relay is in the master cylinder solenoid.

Therefore, solenoid relay circuit inspections and relay unit inspections cannot be performed. Be sure to check if any DTC is output before replacing the master cylinder solenoid.



b.

Drive the vehicle at a speed of approximately 32 km/h (20 mph) or more for 60 seconds or more.


c.

Check if the same DTCs are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR).

HINT:

Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

B

C