Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster) › 2015.06–2020.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260911 VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster)  C1241  Low Power Supply Voltage Malfunction  


DESCRIPTION

If the voltage supplied to the IG1 terminal is within the DTC detection range due to malfunctions in components such as the battery and generator circuit, this DTC is stored.

DTC Code DTC Detection Condition Trouble Area
C1241 Either condition is met:
1. Both of the following conditions continue for at least 10 seconds.
·

The vehicle speed is more than 3 km/h (2 mph).

·

The IG1 terminal voltage is below 9.5 V.


2. All of the following conditions continue for at least 0.2 seconds.
·

The solenoid relay remains on.

·

The IG1 terminal voltage is below 9.5 V.

·

The relay contact is open.


·

Battery

·

ECU-IG NO. 1 fuse

·

Charging system

·

Harness or connector

·

Master cylinder solenoid (Skid control ECU)



WIRING DIAGRAM

C173289E25
3.406,1.083 4.656,1.26 1.25,0.177 10 false ECU-IG NO. 1 0.375,0.927 1.396,1.104 1.021,0.177 10 false from IG1 Circuit 5.51,4.76 7.146,5.167 1.635,0.406 10 false Master Cylinder Solenoid (Skid Control ECU) 6.167,3.323 6.615,3.5 0.448,0.177 10 false GND3 5.833,3.063 5.979,3.24 0.146,0.177 10 false 4 6.167,2.521 6.615,2.698 0.448,0.177 10 false GND2 5.792,2.302 6.01,2.479 0.219,0.177 10 false 32 6.156,1.708 6.604,1.885 0.448,0.177 10 false GND1 5.833,1.49 5.979,1.667 0.146,0.177 10 false 1 6.167,0.906 6.417,1.083 0.25,0.177 10 false IG1 5.781,0.927 5.99,1.083 0.208,0.156 10 false A7 5.781,1.75 6.01,1.896 0.229,0.146 10 false A7 5.792,2.542 6.01,2.708 0.219,0.167 10 false A7 5.781,3.323 6,3.469 0.219,0.146 10 false A8 5.802,0.708 6.031,0.885 0.229,0.177 10 false 46

CAUTION / NOTICE / HINT

NOTICE:
·
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (IG1 VOLTAGE VALUE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Start the engine.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
IG1 Voltage Value IG1 voltage value/ Min.: 0.00 V, Max.: 20.00 V Ignition switch ON: 11 to 14 V -


f.

Check the voltage output from the skid control ECU displayed on the intelligent tester.

OK:

The output voltage displayed on the intelligent tester is within 11 to 14 V.




OK

2.RECONFIRM DTC

NG

3.CHECK TERMINAL VOLTAGE (IG1)
2.RECONFIRM DTC

b.

Check if the same DTCs are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR).

HINT:

Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


Result
Result Proceed to
DTC is output (for LHD) A
DTC is output (for RHD) B
DTC is not output (When troubleshooting in accordance with Diagnostic Trouble Code Chart) C
DTC is not output (When troubleshooting in accordance with Problem Symptoms Table) D



A

B

C

D

3.CHECK TERMINAL VOLTAGE (IG1)
a.

Disconnect the A7 skid control ECU connector.


b.
U148396E02
2.656,1.552 2.656,1.854 false 0.125,0 2.552,0.354 2.427,0.354 10 false *a 2.521,1.896 2.802,2.073 0.281,0.177 10 false IG1 0.281,0.708 0.49,0.875 0.208,0.167 10 false A7

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A7-46 (IG1) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)



OK

4.CHECK HARNESS AND CONNECTOR (GND1, GND2, AND GND3 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (GND1, GND2, AND GND3 TERMINAL)

OK

5.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.RECONFIRM DTC

b.

Check if the same DTCs are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR).

HINT:

Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


Result
Result Proceed to
DTC is output (for LHD) A
DTC is output (for RHD) B
DTC is not output (When troubleshooting in accordance with Diagnostic Trouble Code Chart) C
DTC is not output (When troubleshooting in accordance with Problem Symptoms Table) D



A

B

C

D