Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260911 VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster)  C1407  Open or Short in Rear Speed Sensor RH Circuit  C1408  Open or Short in Rear Speed Sensor LH Circuit  


DESCRIPTION

Refer to DTCs C1401 and C1402 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>C1401).

DTC Code DTC Detection Condition Trouble Area
C1407
C1408
Either condition is met:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the IG1 terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Rear speed sensor RH/LH

·

Rear skid control sensor wire

·

Speed sensor circuit

·

Master cylinder solenoid (Skid control ECU)



HINT:
·

DTC C1407 is for the rear speed sensor RH.

·

DTC C1408 is for the rear speed sensor LH.



WIRING DIAGRAM

C217557E31
5.552,2.698 5.792,2.844 0.24,0.146 10 false A7 5.552,2.885 7.156,3.26 1.604,0.375 10 false Master Cylinder Solenoid (Skid Control ECU) 3.135,2.802 5.156,2.979 2.021,0.177 10 false Rear Skid Control Sensor Wire 3.938,0.333 4.24,0.542 0.302,0.208 10 false Sq1 3.927,1.885 4.229,2.104 0.302,0.219 10 false Sq1 2.823,0.313 3.031,0.583 0.208,0.271 10 false q1 2.802,1.865 3.031,2.083 0.229,0.219 10 false q2 0.479,0.573 2.021,0.781 1.542,0.208 10 false Rear Speed Sensor RH 0.5,2.125 2.042,2.333 1.542,0.208 10 false Rear Speed Sensor LH 2.406,0.854 2.698,1.031 0.292,0.177 10 false RR- 2.854,0.115 2.958,0.26 0.104,0.146 10 false 2 2.396,0.333 2.708,0.51 0.313,0.177 10 false RR+ 4,0.135 4.135,0.302 0.135,0.167 10 false 4 4,0.667 4.177,0.823 0.177,0.156 10 false 3 2.844,0.646 3.021,0.802 0.177,0.156 10 false 1 2.385,2.448 2.677,2.625 0.292,0.177 10 false RL- 2.854,1.688 2.969,1.844 0.115,0.156 10 false 2 2.396,1.854 2.688,2.031 0.292,0.177 10 false RL+ 4,1.677 4.135,1.844 0.135,0.167 10 false 2 3.99,2.229 4.167,2.385 0.177,0.156 10 false 1 2.833,2.229 2.938,2.385 0.104,0.156 10 false 1 6.167,0.854 6.458,1.031 0.292,0.177 10 false RR- 6.156,0.323 6.531,0.5 0.375,0.177 10 false RR+ 6.167,2.385 6.458,2.563 0.292,0.177 10 false RL- 6.167,1.823 6.458,2 0.292,0.177 10 false RL+ 5.875,0.167 6.042,0.365 0.167,0.198 10 false 5 5.823,0.708 6.021,0.875 0.198,0.167 10 false 19 5.802,1.74 6.01,1.906 0.208,0.167 10 false 20 5.875,2.292 6.021,2.479 0.146,0.188 10 false 6 2.802,2.438 3.01,2.688 0.208,0.25 10 false q2 3.927,2.427 4.219,2.688 0.292,0.26 10 false Sq1 2.813,0.854 3.073,1.135 0.26,0.281 10 false q1 3.938,0.875 4.219,1.042 0.281,0.167 10 false Sq1

CAUTION / NOTICE / HINT

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>CHECK FOR INTERMITTENT PROBLEMS).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Speed Open Rear speed sensor RH open detection/ Error or Normal Normal -
RL Speed Open Rear speed sensor LH open detection/ Error or Normal Normal -

OK:

Normal (there are no momentary interruptions).


HINT:

Perform the above inspection before removing the sensor and connector.




OK

2.READ VALUE USING INTELLIGENT TESTER (RR/RL WHEEL SPEED)

NG

4.INSPECT SKID CONTROL SENSOR WIRE
2.READ VALUE USING INTELLIGENT TESTER (RR/RL WHEEL SPEED)

OK

3.RECONFIRM DTC

NG

4.INSPECT SKID CONTROL SENSOR WIRE
3.RECONFIRM DTC
a.

Turn the ignition switch off.



c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

B

C

4.INSPECT SKID CONTROL SENSOR WIRE
U148452E01
0.057,0.026 0.247,0.188 0.191,0.163 10 *1 5.818,0.887 6.002,1.040 0.184,0.152 10 q1 1.176,0.851 1.360,1.003 0.184,0.152 10 q2 6.085,0.786 6.309,0.973 0.224,0.187 10 *A 1.433,0.73 1.672,0.913 0.239,0.184 10 *B 3.453,0.71 3.727,0.863 0.274,0.152 10 Sq1 1.666,2.099 2.003,2.262 0.336,0.163 10 RL+ 0.711,2.089 1.048,2.252 0.336,0.163 10 RL- 6.297,2.11 6.633,2.273 0.336,0.163 10 RR+ 5.337,2.11 5.674,2.273 0.336,0.163 10 RR- 1.125,1.549 0.803,1.942 0.803,1.942 0.803,2.04 false 1.431,1.562 1.776,1.935 1.776,1.935 1.778,2.032 false 5.758,1.577 5.436,1.969 5.436,1.969 5.436,2.068 false 6.065,1.59 6.41,1.962 6.41,1.962 6.412,2.06 false

Text in Illustration
*A for RH *B for LH
*1 Skid Control Sensor Wire - -

a.

Remove the skid control sensor wire (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
Sq1-4 - q1-2 (RR+) Always Below 1 Ω
Sq1-3 - q1-1 (RR-) Always Below 1 Ω
Sq1-4 - Sq1-3 Always 10 kΩ or higher
Sq1-4 - Sq1-1 Always 10 kΩ or higher
Sq1-4 - Sq1-2 Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
Sq1-2 - q2-2 (RL+) Always Below 1 Ω
Sq1-1 - q2-1 (RL-) Always Below 1 Ω
Sq1-2 - Sq1-1 Always 10 kΩ or higher
Sq1-2 - Sq1-3 Always 10 kΩ or higher
Sq1-2 - Sq1-4 Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)

NG

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)
a.

Install the skid control sensor wire.


b.

Disconnect the A7 skid control ECU connector.


c.

Disconnect the q1 and/or q2 speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A7-5 (RR+) - q1-2 (RR+) Always Below 1 Ω
A7-5 (RR+) - Body ground Always 10 kΩ or higher
A7-19 (RR-) - q1-1 (RR-) Always Below 1 Ω
A7-19 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A7-20 (RL+) - q2-2 (RL+) Always Below 1 Ω
A7-20 (RL+) - Body ground Always 10 kΩ or higher
A7-6 (RL-) - q2-1 (RL-) Always Below 1 Ω
A7-6 (RL-) - Body ground Always 10 kΩ or higher




OK

6.CHECK TERMINAL VOLTAGE (RR+, RL+)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK TERMINAL VOLTAGE (RR+, RL+)
a.

Disconnect the q1 and/or q2 speed sensor connector.


b.

Connect the A7 skid control ECU connector.


c.
U148291E01
0.071,0.103 0.301,0.296 0.230,0.193 10 *a 1.572,0.111 1.756,0.273 0.184,0.163 10 q1 1.568,0.403 1.752,0.566 0.184,0.163 10 q2 1.908,0.028 2.095,0.187 0.187,0.159 10 *A 1.908,0.355 2.095,0.514 0.187,0.159 10 *B 2.552,1.392 3.055,1.733 0.503,0.341 10 RR+*A, RL+*B 1.899,1.174 2.81,1.289 2.81,1.289 2.81,1.392 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Switch Condition Specified Condition
q1-2 (RR+) - Body ground Ignition switch ON 11 to 14 V

for LH
Tester Connection Switch Condition Specified Condition
q2-2 (RL+) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*A for RH
*B for LH
*a Front view of wire harness connector
(to Rear Speed Sensor)

Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

B

C