Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster) › 2015.06–2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260911 VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster)  C1232  Acceleration Sensor Stuck Malfunction  C1243  Acceleration Sensor Stuck Malfunction  C1245  Acceleration Sensor Output Malfunction  C1279  Acceleration Sensor Output Voltage Malfunction (Test Mode DTC)  


DESCRIPTION

The skid control ECU receives signals from the yaw rate and acceleration sensor via the CAN communication system.

If there is trouble in the bus lines between the yaw rate and acceleration sensor and the CAN communication system, DTCs U0123 (yaw rate sensor communication trouble) and U0124 (acceleration sensor communication trouble) are stored.

DTC Code DTC Detection Condition Trouble Area
C1232 At a vehicle speed of 10 km/h (6 mph) or more, the fluctuation range of the signal from one of either GL1 or GL2 is below 80 mV and the fluctuation range of the signal of the other is higher than 1.9 V for 30 seconds or more.
·

ECU-IG NO. 1 fuse

·

Sensor installation

·

Harness or connector

·

Yaw rate and acceleration sensor

·

CAN communication system


C1243 The following condition repeats 16 times.
·

GL1 and GL2 do not change when the vehicle decelerates from 30 km/h (19 mph) to 0 km/h (0 mph).


C1245 The following condition continues for at least 60 seconds.
·

The difference between the values calculated from the acceleration sensor value and vehicle speed exceeds 0.35 G.


C1279 Stored during test mode.

WIRING DIAGRAM

C185399E04
0.366,1.489 3.328,1.742 2.961,0.253 10 Master Cylinder Solenoid (Skid Control ECU) 4.649,2.152 6.870,2.338 2.221,0.186 10 Yaw Rate and Acceleration Sensor 5.592,0.742 5.813,0.944 0.221,0.202 10 IG 5.989,1.405 6.349,1.607 0.360,0.202 10 GND 5.781,0.422 5.942,0.671 0.161,0.248 10 4 6.522,1.215 6.664,1.417 0.142,0.202 10 1 1.95,0.182 2.955,0.356 1.005,0.174 10 from IG1 Circuit 0.712,2.374 3.099,2.548 2.387,0.174 10 : CAN Communication System 3.72,0.359 4.635,0.533 0.915,0.174 10 ECU-IG NO. 1 4.649,1.994 4.967,2.159 0.318,0.165 10 G52 0.366,1.326 0.588,1.486 0.222,0.161 10 A7

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the yaw rate and acceleration sensor, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK FOR DTC

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

Check if DTCs U0073, U0123, C1210 and/or C1336 are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC U0073, U0123, C1210 and/or C1336 are not output A
DTC U0073 and/or U0123 are output (for LHD) B
DTC U0073 and/or U0123 are output (for RHD) C
DTC C1210 and/or C1336 are output D



A

2.CHECK YAW RATE AND ACCELERATION SENSOR INSTALLATION

B

C

D

2.CHECK YAW RATE AND ACCELERATION SENSOR INSTALLATION
a.

Check that the yaw rate and acceleration sensor is installed properly.

OK:

The sensor is tightened to the specified torque. The sensor is not tilted.




OK

3.CHECK TERMINAL VOLTAGE AND RESISTANCE (IG, GND)

NG

INSTALL YAW RATE AND ACCELERATION SENSOR CORRECTLY

3.CHECK TERMINAL VOLTAGE AND RESISTANCE (IG, GND)
a.

Disconnect the G52 yaw rate and acceleration sensor connector.


b.
U148294E03
1.208,1.167 0.792,1.688 false 1.781,1.219 2.448,1.75 false 0.115,0.052 0.406,0.271 0.292,0.219 10 false *a 0.542,1.802 0.896,1.979 0.354,0.177 10 false GND 2.438,1.813 2.677,1.99 0.24,0.177 10 false IG 0.302,0.854 0.615,1.021 0.313,0.167 10 false G52

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G52-4 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G52-1 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor)

Result
Result Proceed to
OK (When troubleshooting in accordance with Diagnostic Trouble Code Chart) A
OK (When troubleshooting in accordance with Problem Symptoms Table) B
NG C


A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR