Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster) › 2015.06–2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260911 VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster)  C1379  Downhill Assist Control Switch Malfunction (Test Mode DTC)  


DESCRIPTION

w/ Downhill Assist Control:

DTC C1379 is cleared when the downhill assist control switch sends a downhill assist control operation signal or when test mode ends.

w/ Crawl Control:

DTC C1379 is cleared when the crawl on/off switch (center cluster module switch) and crawl speed selector (center cluster module switch) send a crawl control operation signal or when test mode ends.

DTC Code DTC Detection Condition Trouble Area
C1379 Stored only during test mode.
·

Downhill assist control switch (w/ Downhill Assist Control)

·

Crawl on/off switch (Center cluster module switch) (w/ Crawl Control)

·

Crawl speed selector (Center cluster module switch) (w/ Crawl Control)

·

Harness or connector

·

Skid control ECU (Master cylinder solenoid)



WIRING DIAGRAM

C214516E10
0.112,0 2.657,0.202 2.545,0.202 12 w/ Downhill Assist Control: 1.837,1.278 3.761,1.483 1.924,0.205 10 Downhill Assist Control Switch 5.299,0.848 5.760,1.017 0.461,0.169 10 HDCS 4.988,0.713 5.232,0.925 0.244,0.211 10 44 4.887,1.671 6.580,2.074 1.693,0.404 10 Skid Control ECU (Master Cylinder Solenoid) 4.887,1.527 5.099,1.690 0.211,0.163 10 A7 1.837,1.138 2.554,1.294 0.717,0.156 10 G158 3.356,0.676 3.516,0.869 0.160,0.193 10 4 1.973,0.676 2.102,0.879 0.129,0.202 10 1

C293884E04
4.458,1.073 6,1.24 1.542,0.167 10 false Crawl On/Off Switch 1.917,2.219 2.344,2.396 0.427,0.177 10 false MOD2 2.458,0.792 2.677,0.969 0.219,0.177 10 false 6 2.469,2.125 2.656,2.302 0.188,0.177 10 false 2 3.938,0.76 4.167,0.927 0.229,0.167 10 false 21 4.219,0.771 4.594,0.948 0.375,0.177 10 false FRB 4.188,2.125 4.458,2.292 0.271,0.167 10 false UP 4.177,2.396 4.427,2.573 0.25,0.177 10 false DN 6.167,0.771 6.344,0.938 0.177,0.167 10 false E 6.385,0.781 6.677,0.938 0.292,0.156 10 false 24 4.125,3.896 6.656,4.333 2.531,0.438 10 false Center Cluster Module Switch 0.802,3.979 2.26,4.323 1.458,0.344 10 false Driving Support Switch Control ECU 3.448,5.708 6.354,5.896 2.906,0.188 10 false Skid Control ECU (Master Cylinder Solenoid) 0.708,6.208 3.146,6.406 2.438,0.198 10 false : CAN Communication System 0.156,0.042 1.719,0.271 1.563,0.229 12 false w/ Crawl Control: 0.802,3.823 1.302,3.969 0.5,0.146 10 false G162 4.125,3.698 4.49,3.865 0.365,0.167 10 false G156 3.448,5.552 3.667,5.719 0.219,0.167 10 false A7 1.854,0.833 2.323,0.99 0.469,0.156 10 false CRWL 1.917,2.49 2.344,2.667 0.427,0.177 10 false MOD3 1.917,1.948 2.344,2.125 0.427,0.177 10 false MOD1 2.417,2.385 2.604,2.563 0.188,0.177 10 false 11 2.448,1.885 2.635,2.063 0.188,0.177 10 false 4 4.167,1.854 4.542,2.031 0.375,0.177 10 false ECU 3.938,1.865 4.125,2.042 0.188,0.177 10 false 17 3.938,2.125 4.125,2.302 0.188,0.177 10 false 18 3.948,2.385 4.135,2.563 0.188,0.177 10 false 19 5.594,1.74 5.781,1.917 0.188,0.177 10 false 5 5.323,1.74 5.51,1.917 0.188,0.177 10 false 4 5.073,1.74 5.26,1.917 0.188,0.177 10 false 3 4.833,1.75 5.021,1.927 0.188,0.177 10 false 2 4.583,1.74 4.771,1.917 0.188,0.177 10 false 1 4.458,2.958 6,3.125 1.542,0.167 10 false Crawl Speed Selector

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (master cylinder solenoid), perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>CALIBRATION).


PROCEDURE

1.CONFIRM VEHICLE SPECIFICATIONS
a.

Confirm the vehicle specifications.

Result
Result Proceed to
w/ Downhill Assist Control A
w/ Crawl Control B



A

2.READ VALUE USING GTS (DOWNHILL ASSIST CONTROL SW)

B

6.CHECK CAN BUS
2.READ VALUE USING GTS (DOWNHILL ASSIST CONTROL SW)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

Check the Data List for proper functioning of the downhill assist control switch.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Downhill Assist Control SW Downhill assist control switch / ON or OFF ON: Downhill assist control on
OFF: Downhill assist control off
-

OK:

The GTS displays ON or OFF according to downhill assist control switch operation.




OK

3.CHECK TEST MODE DTC

NG

4.INSPECT DOWNHILL ASSIST CONTROL SWITCH
3.CHECK TEST MODE DTC
a.

Perform the downhill assist control switch check in the Test Mode Procedure (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>TEST MODE PROCEDURE).

OK:

Test mode DTC C1379 is cleared.


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

B

C

4.INSPECT DOWNHILL ASSIST CONTROL SWITCH

OK

5.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - DOWNHILL ASSIST CONTROL SWITCH)

NG

5.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - DOWNHILL ASSIST CONTROL SWITCH)
a.

Disconnect the A7 skid control ECU (master cylinder solenoid) connector.


b.

Disconnect the G158 downhill assist control switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A7-44 (HDCS) - G158-4 Always Below 1 Ω
A7-44 (HDCS) or G158-4 - Body ground Always 10 kΩ or higher
G158-1 - Body ground Always Below 1 Ω


Result
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C

6.CHECK CAN BUS
a.

Check that there are no problems with the CAN communication system (for LHD: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)>DIAGNOSIS SYSTEM, for RHD: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

7.READ VALUE USING GTS (CRAWL CONTROL MAIN SWITCH AND DIAL SWITCH SIGNAL)

B

C

7.READ VALUE USING GTS (CRAWL CONTROL MAIN SWITCH AND DIAL SWITCH SIGNAL)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / D-SEAT SW / Data List.


f.

Check the Data List for proper functioning of the crawl on/off switch (center cluster module switch) and crawl speed selector (center cluster module switch).

D-SEAT SW
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Crawl Control Main Switch Crawl on/off switch/ ON or OFF ON: Switch on
OFF: Switch off
-
Dial Switch Signal 1 Crawl speed selector/Multi-terrain select road mode selector signal 1/ ON or OFF Switches between ON and OFF according to the ON/OFF Combination Chart below. -
Dial Switch Signal 2 Crawl speed selector/Multi-terrain select road mode selector signal 2/ ON or OFF -
Dial Switch Signal 3 Crawl speed selector/Multi-terrain select road mode selector signal 3/ ON or OFF -

i.
C293382E06
2.281,0.75 2.729,1.052 2.729,1.052 2.938,1.052 false 1.115,0.74 0.594,0.979 0.594,0.979 0.375,0.979 false 1.021,1.646 0.656,2.458 0.656,2.458 0.417,2.458 false 1.26,1.208 0.563,1.573 0.563,1.573 0.375,1.573 false 1.708,1.021 2.104,0.188 2.104,0.188 2.25,0.188 false 2.177,1.219 2.885,1.698 2.885,1.698 3.167,1.698 false 2.427,1.667 2.677,2.406 2.677,2.406 2.927,2.406 false 2.063,2.135 2.313,3.156 2.313,3.156 2.552,3.156 false 0.094,0.052 0.344,0.292 0.25,0.24 10 false *1 3.021,0.969 3.271,1.208 0.25,0.24 10 false *2 0.198,0.865 0.448,1.104 0.25,0.24 10 false *3 0.26,2.375 0.51,2.615 0.25,0.24 10 false *a 0.219,1.479 0.469,1.719 0.25,0.24 10 false *b 2.292,0.073 2.542,0.313 0.25,0.24 10 false *c 3.177,1.625 3.427,1.865 0.25,0.24 10 false *d 3.01,2.323 3.26,2.563 0.25,0.24 10 false *e 2.594,3.042 2.844,3.281 0.25,0.24 10 false *4

Operate the crawl speed selector/multi-terrain select road mode selector and check that "Dial Switch Signal 1", "Dial Switch Signal 2" and "Dial Switch Signal 3" in the Data List display ON and OFF according to the chart shown below.

Text in Illustration
*1 Center Cluster Module Switch
*2 Crawl On/Off Switch
*3 Multi-terrain Select Switch
*4 Crawl Speed Selector/Multi-terrain Select Road Mode Selector
*a Low/MUD & SAND
*b Medium-low/LOOSE ROCK
*c Medium/MOGUL
*d Medium-high/ROCK & DIRT
*e High/ROCK

ON/OFF Combination Chart for "Dial Switch Signal 1", "Dial Switch Signal 2" and "Dial Switch Signal 3"
Crawl Speed Selector Position/Multi-terrain Select Road Mode Selector Position Low/MUD & SAND Medium-low/LOOSE ROCK Medium/MOGUL Medium-high/ROCK & DIRT High/ROCK
Data List Display Dial Switch Signal 1 ON ON OFF OFF OFF
Dial Switch Signal 2 ON OFF OFF OFF ON
Dial Switch Signal 3 OFF OFF OFF ON ON

OK:

The GTS display changes according to crawl on/off switch (center cluster module switch) and crawl speed selector (center cluster module switch) operation.





OK

8.CHECK TEST MODE DTC

NG

9.CHECK HARNESS AND CONNECTOR (CENTER CLUSTER MODULE SWITCH - DRIVING SUPPORT SWITCH CONTROL ECU)
8.CHECK TEST MODE DTC
a.

Perform the crawl on/off switch (center cluster module switch) and crawl speed selector (center cluster module switch) check in the Test Mode Procedure (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>TEST MODE PROCEDURE).

OK:

Test mode DTC C1379 is cleared.


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

B

C

9.CHECK HARNESS AND CONNECTOR (CENTER CLUSTER MODULE SWITCH - DRIVING SUPPORT SWITCH CONTROL ECU)
a.

Disconnect the G156 center cluster module switch connector.


b.

Disconnect the G162 driving support switch control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G162-6 (CRWL) - G156-21 (FRB) Always Below 1 Ω
G162-4 (MOD1) - G156-17 (ECU) Always Below 1 Ω
G162-11 (MOD3) - G156-19 (DN) Always Below 1 Ω
G162-2 (MOD2) - G156-18 (UP) Always Below 1 Ω
G156-24 (E) - Body ground Always Below 1 Ω
G162-6 (CRWL) or G156-21 (FRB) - Body ground Always 10 kΩ or higher
G162-4 (MOD1) or G156-17 (ECU) - Body ground Always 10 kΩ or higher
G162-11 (MOD3) or G156-19 (DN) - Body ground Always 10 kΩ or higher
G162-2 (MOD2) or G156-18 (UP) - Body ground Always 10 kΩ or higher




OK

10.INSPECT CENTER CLUSTER MODULE SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT CENTER CLUSTER MODULE SWITCH
a.

Remove the center cluster module switch (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>CRAWL SWITCH>REMOVAL).


b.

Inspect the crawl on/off switch (center cluster module switch) and crawl speed selector (center cluster module switch) (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>CRAWL SWITCH>INSPECTION).



OK

REPLACE DRIVING SUPPORT SWITCH CONTROL ECU

NG

REPLACE CENTER CLUSTER MODULE SWITCH