Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260911 VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster)  C1242  Open Circuit in IG1/IG2 Power Source Circuit  


DESCRIPTION

If there is a problem with the master cylinder solenoid (skid control ECU) power supply circuit, the skid control ECU stores DTCs and prohibits operation under the fail-safe function.

If the voltage supplied to the IG2 terminal is within the DTC detection range due to malfunctions in components such as the battery and generator circuit, this DTC is stored.

DTC Code DTC Detection Condition Trouble Area
C1242 The vehicle speed is 3 km/h (2 mph) or more and the voltage at the ECU IG2 terminal remains below 6.5 V for more than 7 seconds.
·

Battery

·

IGN fuse

·

Charging system

·

Harness or connector

·

Master cylinder solenoid (Skid control ECU)



WIRING DIAGRAM

C173290E21
0.344,0.927 1.344,1.104 1,0.177 10 false from IG2 Circuit 5.479,4.813 7.094,5.219 1.615,0.406 10 false Master Cylinder Solenoid (Skid Control ECU) 6.167,3.313 6.615,3.49 0.448,0.177 10 false GND3 5.833,3.031 5.979,3.208 0.146,0.177 10 false 4 6.167,2.552 6.615,2.729 0.448,0.177 10 false GND2 5.792,2.292 6.01,2.469 0.219,0.177 10 false 32 6.167,1.729 6.615,1.906 0.448,0.177 10 false GND1 5.802,1.74 6.073,1.917 0.271,0.177 10 false A7 5.802,2.542 6.073,2.719 0.271,0.177 10 false A7 5.833,1.49 5.979,1.667 0.146,0.177 10 false 1 6.167,0.927 6.438,1.104 0.271,0.177 10 false IG2 5.802,0.938 6.021,1.115 0.219,0.177 10 false A8 5.802,3.313 6.073,3.49 0.271,0.177 10 false A8 5.823,0.688 5.99,0.865 0.167,0.177 10 false 1 3.677,1.125 4.031,1.302 0.354,0.177 10 false IGN

CAUTION / NOTICE / HINT

NOTICE:
·
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (IG2)
a.

Disconnect the A8 skid control ECU connector.


b.
U148401E04
1.573,0.875 1.073,1.229 false 0.854,0.542 1.063,0.708 0.208,0.167 10 false A8 0.177,0.021 0.375,0.25 0.198,0.229 10 false *a 0.729,1.219 1.01,1.396 0.281,0.177 10 false IG2 1.573,0.76 1.688,0.958 0.115,0.198 10 false 1 1.76,0.75 1.875,0.948 0.115,0.198 10 false 2 1.573,0.969 1.688,1.167 0.115,0.198 10 false 3 1.76,0.969 1.875,1.167 0.115,0.198 10 false 4

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A8-1 (IG2) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)



OK

2.CHECK HARNESS AND CONNECTOR (GND1, GND2 AND GND3 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (GND1, GND2 AND GND3 TERMINAL)

OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.RECONFIRM DTC

b.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR).

HINT:

Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

B

C