Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) › 2015.06–2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260912 VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)  ABS Warning Light Remains ON  


DESCRIPTION

The skid control ECU is connected to the combination meter via CAN communication.

If any of the following is detected, the ABS warning light remains on:

·

The skid control ECU connector is disconnected from the skid control ECU.

·

There is a malfunction in the skid control ECU internal circuit.

·

There is an open in the harness between the combination meter and the skid control ECU.

·

The anti-lock brake system is defective.

·

The voltage at terminal IG1 is high.


HINT:

In some cases, the intelligent tester cannot be used when the skid control ECU is abnormal.


WIRING DIAGRAM

C215178E01
1.051,1.494 1.412,1.659 0.362,0.165 10 ABS 1.316,1.974 1.593,2.145 0.277,0.171 10 IG 5.146,2.479 6.747,2.843 1.600,0.364 10 Brake Actuator Assembly (Skid Control ECU) 5.352,1.839 5.637,2.005 0.286,0.165 10 IG1 5.361,1.083 5.799,1.262 0.438,0.179 10 GND1 5.02,1.718 5.222,1.888 0.202,0.170 10 34 5.081,0.966 5.228,1.136 0.147,0.170 10 1 2.865,1.83 3.878,2.023 1.014,0.193 10 from IG1 Circuit 0.546,2.652 1.804,2.822 1.258,0.170 10 Combination Meter 0.577,3.293 3.228,3.472 2.651,0.179 10 : CAN Communication System 0.85,0.677 1.367,0.874 0.517,0.198 10 CPU 5.146,2.344 5.381,2.504 0.235,0.161 10 A6 4.103,1.987 5.069,2.152 0.966,0.165 10 ECU-IG NO. 1 0.546,2.526 0.809,2.677 0.262,0.151 10 G6

CAUTION / NOTICE / HINT

NOTICE:
·
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output (for LHD without Entry and Start System: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD without Entry and Start System)>DIAGNOSIS SYSTEM, for LHD with Entry and Start System: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
DTC not output A
DTC output for LHD without Entry and Start System B
DTC output for LHD with Entry and Start System C



A

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

B

C

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU connector is securely connected.

OK:

The connector is securely connected.




OK

3.CHECK TERMINAL VOLTAGE (IG1)

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.CHECK TERMINAL VOLTAGE (IG1)

OK

4.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

OK

5.READ VALUE USING INTELLIGENT TESTER (ABS WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

5.READ VALUE USING INTELLIGENT TESTER (ABS WARNING LIGHT)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ABS Warning Light ABS warning light / ON or OFF OFF -

f.

When performing the ABS Warning Light Active Test, check ABS Warning Light in the Data List (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>DATA LIST / ACTIVE TEST).


ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
ABS Warning Light ABS warning light Warning light ON/OFF Observe the combination meter.

Result
Result Proceed to
Data List Display Data List Display when Performing Active Test ON/OFF Operation
ON Does not change between ON and OFF A
Changes between ON and OFF B
OFF Does not change between ON and OFF A
Changes between ON and OFF B


A

B

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)