Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) › 2015.06–2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260912 VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)  C1232  Acceleration Sensor Stuck Malfunction  C1243  Acceleration Sensor Stuck Malfunction  C1245  Acceleration Sensor Output Malfunction  C1279  Acceleration Sensor Output Voltage Malfunction (Test Mode DTC)  


DESCRIPTION

The skid control ECU receives signals from the yaw rate and acceleration sensor via the CAN communication system.

The yaw rate sensor has a built-in acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2).

If there is trouble in the bus lines between the yaw rate and acceleration sensor and the CAN communication system, DTCs U0123 (malfunction in CAN communication with the yaw rate sensor) and U0124 (malfunction in CAN communication with the acceleration sensor) are stored.

These DTCs are also stored when calibration has not been completed.

DTC C1279 can be cleared when the yaw rate and acceleration sensor sends a yaw rate and/or acceleration signal or test mode ends. DTC C1279 is stored only in test mode.

DTC Code DTC Detection Condition Trouble Area
C1232 At a vehicle speed of 10 km/h (6 mph) or more, either GL1 or GL2 (input signal) does not change for 30 seconds or more.
·

Yaw rate and acceleration sensor

·

Yaw rate and acceleration sensor circuit


C1243 While the vehicle speed changes from 30 km/h (19 mph) to 0 km/h (0 mph), the condition that the values of GL1 and GL2 do not change by 0.0294 G or more occurs 16 times or more.
·

Yaw rate and acceleration sensor

·

Yaw rate and acceleration sensor circuit


C1245 At a vehicle speed of 30 km/h (19 mph) or more, the difference between the forward and backward G calculated from the acceleration sensor value and that calculated from the vehicle speed exceeds 0.35 G for 60 seconds or more.
·

Yaw rate and acceleration sensor

·

Yaw rate and acceleration sensor circuit

·

Sensor installation


C1279 Stored only during test mode.
·

Yaw rate and acceleration sensor

·

Sensor installation



WIRING DIAGRAM

C185399E05
0.366,1.487 3.328,1.740 2.961,0.253 10 Brake Actuator Assembly (Skid Control ECU) 0.759,2.366 3.033,2.543 2.274,0.177 10 : CAN Communication System 4.808,2.221 7.089,2.384 2.281,0.163 10 Yaw Rate and Acceleration Sensor 0.366,1.317 0.578,1.486 0.211,0.170 10 A6 3.785,0.387 4.746,0.536 0.961,0.149 10 ECU-IG NO. 1 1.875,0.163 2.943,0.360 1.068,0.198 10 from IG1 Circuit 5.592,0.744 5.880,0.984 0.288,0.239 10 IG 6.02,1.389 6.412,1.552 0.392,0.163 10 GND 5.746,0.45 5.934,0.641 0.187,0.191 10 4 6.475,1.224 6.700,1.443 0.225,0.218 10 1 4.808,2.067 5.155,2.223 0.347,0.156 10 G52

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the yaw rate and acceleration sensor, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When DTC U0123, U0124 and/or U0126 is output together with DTC C1232, C1243 and/or C1245, inspect and repair the trouble areas indicated by DTC U0123, U0124 and/or U0126 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>U0073).


PROCEDURE

1.CHECK DTC

b.

Turn the ignition switch off.


c.

At a speed of 30 km/h (19 mph) or more, drive the vehicle, turn the steering wheel and decelerate (depress the brake pedal) the vehicle.


d.

Turn the ignition switch to ON again and check that no CAN communication system DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>DTC CHECK / CLEAR).


e.

Check if DTCs for zero point calibration of the yaw rate and acceleration sensor (C1210) or for zero point calibration of the acceleration sensor (C1336) are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC output (relating to yaw rate and acceleration sensor) A
DTC output (relating to CAN communication system) for LHD without Entry and Start System B
DTC output (relating to CAN communication system) for LHD with Entry and Start System C
DTC (C1210 and/or C1336) output D



A

2.CHECK YAW RATE AND ACCELERATION SENSOR INSTALLATION

B

C

D

2.CHECK YAW RATE AND ACCELERATION SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the yaw rate and acceleration sensor is installed properly (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>YAW RATE AND ACCELERATION SENSOR>INSTALLATION).

OK:

The sensor is tightened to the specified torque.

The sensor is not tilted.




OK

3.CHECK TERMINAL VOLTAGE (IG, GND)

NG

INSTALL YAW RATE AND ACCELERATION SENSOR CORRECTLY

3.CHECK TERMINAL VOLTAGE (IG, GND)
a.

Disconnect the G52 yaw rate and acceleration sensor connector.


b.
U148294E05
1.208,1.167 0.792,1.688 false 1.781,1.177 2.448,1.708 false 0.115,0.052 0.406,0.271 0.292,0.219 10 false *a 0.542,1.729 0.896,1.906 0.354,0.177 10 false GND 2.417,1.75 2.656,1.927 0.24,0.177 10 false IG 0.302,0.823 0.615,0.99 0.313,0.167 10 false G52

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G52-4 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G52-1 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor)

Result
Result Proceed to
OK (When troubleshooting in accordance with diagnostic trouble code chart) A
OK (When troubleshooting in accordance with problem symptoms table) B
NG C


A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR