The skid control ECU (brake actuator assembly) inputs stop light switch signals and brake operation condition.
The skid control ECU (brake actuator assembly) has an open detection circuit, which stores this DTC when detecting an open in the stop light input line or the ground line of the stop light circuit with the stop light switch off (brake pedal not depressed).
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1426 | When the brake pedal load sensing switch is on, the master cylinder pressure is 2 MPa or higher and the deceleration calculated from the vehicle speed is 0.2 G or more, the stop light switch is off for 2 seconds or more. | ·
STOP fuse ·
Stop light switch assembly ·
Stop light switch circuit ·
Skid control ECU (Brake actuator assembly) ·
Brake pedal load sensing switch (Brake with switch pedal sub-assembly) |
Refer to DTC C1425 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>C1425).
When replacing the skid control ECU (brake actuator assembly), perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>CALIBRATION).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.
| Condition | Illumination Condition |
|---|---|
| Brake pedal depressed | On |
| Brake pedal released | Off |
OK
NG
Turn the ignition switch off
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Stop Light SW | Stop light switch/ ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
| Brake Pedal Load Sensing SW | Brake pedal load sensing switch/ ON or OFF | ON: Brake pedal depressed beyond specified point
OFF: Brake pedal not depressed beyond specified point |
- |
Check that the stop light switch display and brake pedal load sensing switch display observed on the intelligent tester change according to the brake pedal operation.
The intelligent tester displays ON or OFF according to brake pedal operation.
Slowly depress the brake pedal and check when the stop light switch and brake pedal load sensing switch are turned on.
The stop light switch turns on first, and then the brake pedal load sensing switch turns on.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Turning on of stop light switch is not confirmed) | B |
| NG (Brake pedal load sensing switch turns on first) | C |
A
B
C
Turn the ignition switch off.
Start the engine.
Depress the brake pedal several times to test the stop light circuit.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1426 is not output | A |
| DTC C1426 is output | B |
A
B
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
OK
NG
OK
NG
OK
NG
Adjust the brake pedal height and stop light switch assembly installation (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for Vacuum Brake Booster)>ADJUSTMENT).
NEXT
Start the engine.
Depress the brake pedal several times to test the stop light circuit.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1426 is not output | A |
| DTC C1426 is output | B |
A
B