Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › 2015.06–2017.08
RM27T0E _56 Audio / Visual / Telematics _053720 AUDIO / VIDEO _0260969 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  B15D8  Monitor Disconnected  


DESCRIPTION

The parking assist ECU and radio and display receiver assembly are connected by an AVC-LAN communication line. When an AVC-LAN communication error occurs between the radio and display receiver assembly and parking assist ECU, these DTCs will be stored.

DTC Code DTC Detection Condition Trouble Area
B15D8 A device that is listed in the AVC-LAN connected device record of the master unit is missing.
·

Parking assist ECU power source circuit

·

AVC-LAN circuit

·

Parking assist ECU

·

Radio and display receiver assembly



HINT:
·

Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.

·

The radio and display receiver assembly is the master unit.



WIRING DIAGRAM

B449381E01
0.354,1.281 1.719,1.49 1.365,0.208 10 false from IG1 NO. 1 Relay 0.906,0.844 1.729,1.052 0.823,0.208 10 false from Battery 0.646,1.677 1.667,1.875 1.021,0.198 10 false from ACC Relay 3.073,2.531 3.375,2.74 0.302,0.208 10 false I6 0.896,3.438 3.323,3.646 2.427,0.208 10 false : AVC-LAN Communication Line 2.125,1.844 2.521,2.031 0.396,0.188 10 false ACC 1.854,1.417 2.74,1.604 0.885,0.188 10 false ECU-IG NO.2 2.042,0.99 2.51,1.177 0.469,0.188 10 false ECU-B 5.458,2.396 7.115,2.76 1.656,0.365 10 false Radio and Display Receiver Assembly 5.438,2.198 5.74,2.375 0.302,0.177 10 false H50 3.073,2.708 4.438,2.896 1.365,0.188 10 false Parking Assist ECU 3.146,2.135 3.542,2.323 0.396,0.188 10 false GND1 3.146,1.76 3.542,1.948 0.396,0.188 10 false ACC 3.188,1.271 3.583,1.458 0.396,0.188 10 false IG 3.156,0.854 3.552,1.042 0.396,0.188 10 false +B 3.781,1.271 4.177,1.458 0.396,0.188 10 false TX+ 3.792,1.688 4.188,1.875 0.396,0.188 10 false TX- 5.771,1.271 6.167,1.458 0.396,0.188 10 false TX3+ 5.771,1.688 6.167,1.875 0.396,0.188 10 false TX3-

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).


PROCEDURE

1.CHECK FOR DTC

OK

NG

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)
a.
U149413E03
2.49,0.958 2.698,0.542 2.698,0.542 2.896,0.542 false 1.438,1.333 1.802,1.844 1.802,1.844 1.99,1.844 false 1.302,1.323 1.104,1.833 1.104,1.833 0.927,1.833 false 0.865,0.938 0.677,0.438 0.677,0.438 0.49,0.438 false 1.615,0.333 1.938,0.521 0.323,0.188 10 false I6 2.927,0.448 3.333,0.635 0.406,0.188 10 false GND1 2.021,1.74 2.521,1.927 0.5,0.188 10 false ACC 0.719,1.771 0.917,1.958 0.198,0.188 10 false IG 0.26,0.365 0.51,0.552 0.25,0.188 10 false +B 0.021,0 0.271,0.188 0.25,0.188 10 false *a

Disconnect the parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I6-4 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I6-1 (+B) - I6-4 (GND1) Always 11 to 14 V
I6-8 (IG) - I6-4 (GND1) Ignition switch ON 11 to 14 V
I6-9 (ACC) - I6-4 (GND1) Ignition switch ACC 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Parking Assist ECU)


OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E268443E03
2.076,0.406 2.443,0.569 0.366,0.163 10 TX3+ 0.697,0.407 1.064,0.569 0.367,0.163 10 TX3- 1.649,1.046 1.829,0.49 1.829,0.49 2.052,0.49 false 1.527,1.046 1.366,0.49 1.366,0.49 1.139,0.49 false

Remove the radio and display receiver assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (TX3+) - 8 (TX3-) Always 60 to 80 Ω




OK

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARKING ASSIST ECU)

NG

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARKING ASSIST ECU)
a.

Disconnect the H50 radio and display receiver assembly connector.


b.

Disconnect the I6 parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H50-7 (TX3+) - I6-11 (TX+) Always Below 1 Ω
H50-8 (TX3-) - I6-10 (TX-) Always Below 1 Ω
H50-7 (TX3+) - Body ground Always 10 kΩ or higher
H50-8 (TX3-) - Body ground Always 10 kΩ or higher




OK

5.CHECK PARKING ASSIST ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR