This DTC is stored when a malfunction occurs in the digital audio broadcasting antenna assembly which is connected to the radio and display receiver assembly.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B157D | The digital audio broadcasting antenna assembly is not connected | ·
Digital audio broadcasting antenna assembly ·
No. 2 antenna cord sub-assembly ·
Windshield glass (window glass antenna wire) ·
Harness or connector ·
Radio and display receiver assembly |
When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).
Check for DTCs (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>DTC CHECK / CLEAR).
No DTCs are not output.
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG
Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.
Optional components are installed.
Do not remove optional components without permission of the customer.
OK
NG
Inspect the windshield glass (window glass antenna wire) (See page Audio / Visual / Telematics>AUDIO / VIDEO>WINDOW GLASS ANTENNA WIRE>REPAIR).
OK
NG
Remove the antenna connector from the radio and display assembly.
Turn the ignition switch to ACC with the radio and display assembly connector connected.
Turn on the radio and turn into AM mode.
Place a screwdriver, thin wire or other metal object on the radio and display receiver assembly antenna jack and check that noise can be heard from the speakers.
Noise occurs.
OK
NG
(See pageAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL)
Disconnect the DB radio and display receiver assembly connector.
Disconnect the antenna connector from the No.2 antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 1 | Always | Below 1 Ω |
| 1-a - 1-a | Always | Below 1 Ω |
| 1 - Body ground | Always | 10 kΩ or higher |
| 1-a - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the antenna connector from the radio and display assembly.
Disconnect the antenna connector from the digital audio broadcasting antenna assembly LH.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 1 | Always | Below 1 Ω |
| 1-a - 1-a | Always | Below 1 Ω |
| 1 - Body ground | Always | 10 kΩ or higher |
| 1-a - Body ground | Always | 10 kΩ or higher |
| *a | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
| *b | Front view of wire harness connector
(to Digital Audio Broadcasting Antenna Assembly) |
OK
NG
Replace the digital audio broadcasting antenna assembly LH with a known good one (See page Audio / Visual / Telematics>AUDIO / VIDEO>DIGITAL AUDIO BROADCASTING ANTENNA>REMOVAL).
Check for DTCs (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>DTC CHECK / CLEAR).
No DTCs are not output.
Perform the above inspection on both LH and RH sides.
OK
NG
Replace the digital audio broadcasting antenna assembly RH with a known good one (See page Audio / Visual / Telematics>AUDIO / VIDEO>DIGITAL AUDIO BROADCASTING ANTENNA>REMOVAL).
OK
NG
(See pageAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL)