Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Navigation Receiver Type) › 2015.06–2020.08
RM27T0E _56 Audio / Visual / Telematics _053721 NAVIGATION / MULTI INFO DISPLAY _0260991 NAVIGATION SYSTEM(for Navigation Receiver Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  B15D8  Monitor Disconnected  


DESCRIPTION

The parking assist ECU and navigation receiver assembly are connected by an AVC-LAN communication line. When an AVC-LAN communication error occurs between the navigation receiver assembly and parking assist ECU, these DTCs will be stored.

DTC Code DTC Detection Condition Trouble Area
B15D8* A device that is listed in the AVC-LAN connected device record of the master unit is missing.
·

Parking assist ECU power source circuit

·

AVC-LAN circuit

·

Parking assist ECU

·

Navigation receiver assembly



HINT:
·

*: Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.

·

The navigation receiver assembly is the master unit.



WIRING DIAGRAM

E286282E05
3.146,0.813 3.469,1.031 0.323,0.219 10 false +B 2.938,0.729 3.094,0.948 0.156,0.219 10 false 1 2.938,1.146 3.094,1.365 0.156,0.219 10 false 8 2.938,1.563 3.094,1.781 0.156,0.219 10 false 9 2.938,1.99 3.094,2.208 0.156,0.219 10 false 4 2.052,0.979 2.75,1.198 0.698,0.219 10 false ECU-B 3.146,1.229 3.469,1.448 0.323,0.219 10 false IG 1.865,1.396 2.771,1.615 0.906,0.219 10 false ECU-IG NO. 2 3.146,1.646 3.469,1.865 0.323,0.219 10 false ACC 3.719,1.229 4.042,1.448 0.323,0.219 10 false TX+ 3.719,1.646 4.042,1.865 0.323,0.219 10 false TX- 4.083,1.104 4.406,1.323 0.323,0.219 10 false 11 4.083,1.521 4.406,1.74 0.323,0.219 10 false 10 5.76,1.229 6.167,1.448 0.406,0.219 10 false TX3+ 5.76,1.646 6.167,1.865 0.406,0.219 10 false TX3- 5.625,2.167 5.948,2.333 0.323,0.167 10 false H55 5.635,2.333 6.906,2.698 1.271,0.365 10 false Navigation Receiver Assembly 2.99,2.521 3.313,2.688 0.323,0.167 10 false I6 2.99,2.688 4.26,2.875 1.271,0.188 10 false Parking Assist ECU 0.833,3.448 3.021,3.635 2.188,0.188 10 false : AVC-LAN Communication Line 5.583,1.104 5.708,1.323 0.125,0.219 10 false 7 5.583,1.521 5.708,1.74 0.125,0.219 10 false 8 3.146,2.073 3.563,2.292 0.417,0.219 10 false GND1 2.135,1.823 2.5,2.042 0.365,0.219 10 false ACC 0.885,0.823 1.667,1.042 0.781,0.219 10 false from Battery 0.313,1.25 1.823,1.469 1.51,0.219 10 false from IG1 NO. 1 Relay 0.615,1.667 1.656,1.885 1.042,0.219 10 false from ACC Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

When replacing the navigation receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).


PROCEDURE

2.CHECK DTC
a.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Navigation Receiver Type)>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

NG

3.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)
a.
U149414E05
2.51,0.938 2.583,0.5 2.583,0.5 2.75,0.5 true 1.438,1.302 1.583,1.833 1.583,1.833 1.75,1.833 true 1.302,1.302 1.167,1.833 1.167,1.833 1,1.833 true 0.865,0.958 0.667,0.5 0.667,0.5 0.5,0.5 true 1.625,0.313 1.948,0.5 0.323,0.188 10 false I6 2.781,0.417 3.281,0.604 0.5,0.188 10 false GND1 1.802,1.729 2.302,1.917 0.5,0.188 10 false ACC 0.813,1.75 1.01,1.938 0.198,0.188 10 false IG 0.271,0.417 0.521,0.604 0.25,0.188 10 false +B 0.021,0 0.271,0.188 0.25,0.188 10 false *a

Disconnect the parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I6-4 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I6-1 (+B) - I6-4 (GND1) Always 11 to 14 V
I6-8 (IG) - I6-4 (GND1) Engine switch on (IG) 11 to 14 V
I6-9 (ACC) - I6-4 (GND1) Engine switch on (ACC) 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Parking Assist ECU)


OK

4.INSPECT NAVIGATION RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT NAVIGATION RECEIVER ASSEMBLY
a.
E268443E07
1.656,1.052 1.833,0.531 1.833,0.531 2.052,0.531 true 1.5,1.052 1.365,0.531 1.365,0.531 1.135,0.531 true 2.063,0.448 2.427,0.615 0.365,0.167 10 false TX3+ 0.844,0.448 1.208,0.615 0.365,0.167 10 false TX3-

Remove the navigation receiver assembly (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION RECEIVER>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (TX3+) - 8 (TX3-) Always 60 to 80 Ω




OK

5.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - PARKING ASSIST ECU)

NG

5.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - PARKING ASSIST ECU)
a.

Disconnect the H55 navigation receiver assembly connector.


b.

Disconnect the I6 parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H55-7 (TX3+) - I6-11 (TX+) Always Below 1 Ω
H55-8 (TX3-) - I6-10 (TX-) Always Below 1 Ω
H55-7 (TX3+) - Body ground Always 10 kΩ or higher
H55-8 (TX3-) - Body ground Always 10 kΩ or higher




OK

6.REPLACE PARKING ASSIST ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE PARKING ASSIST ECU

NEXT

7.CLEAR DTC
8.CHECK DTC

OK

END (PARKING ASSIST ECU IS DEFECTIVE)

NG