Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Navigation Receiver Type) › 2015.06–2017.08
RM27T0E _56 Audio / Visual / Telematics _053721 NAVIGATION / MULTI INFO DISPLAY _0260991 NAVIGATION SYSTEM(for Navigation Receiver Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  B157D  DAB Tuner Antenna Disconnected  


DESCRIPTION

This DTC is stored when a malfunction occurs in the digital audio broadcasting antenna assembly which is connected to the navigation receiver assembly.

DTC Code DTC Detection Condition Trouble Area
B157D The digital audio broadcasting antenna assembly is not connected
·

Digital audio broadcasting antenna assembly

·

No. 2 antenna cord sub-assembly

·

Navigation receiver assembly

·

Harness or connector



WIRING DIAGRAM

E286269E05
5.813,2.583 7.115,3.031 1.302,0.448 10 false Navigation Receiver Assembly 2.813,2.313 4.125,2.667 1.313,0.354 10 false No. 2 Antenna Cord Sub-assembly 0.427,2.271 1.292,3.031 0.865,0.76 10 false Digital Audio Broadcasting Antenna Assembly RH 1.74,2.281 2.604,3.042 0.865,0.76 10 false Digital Audio Broadcasting Antenna Assembly LH 0.135,0.083 2.208,0.302 2.073,0.219 10 false Windshield Glass Antenna Wire 5.479,1.208 5.583,1.365 0.104,0.156 10 false 1 5.354,1.5 5.583,1.656 0.229,0.156 10 false 1-a 4.781,1.208 4.885,1.365 0.104,0.156 10 false 1 4.781,1.51 5.01,1.667 0.229,0.156 10 false 1-a 3.854,1.198 3.958,1.354 0.104,0.156 10 false 1 3.729,1.5 3.958,1.656 0.229,0.156 10 false 1-a 2.896,1.219 3,1.375 0.104,0.156 10 false 1 2.896,1.5 3.125,1.656 0.229,0.156 10 false 1-a 5.813,2.396 6.094,2.552 0.281,0.156 10 false DB

CAUTION / NOTICE / HINT

HINT:

When replacing the navigation receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).


PROCEDURE

2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

OK:

Optional components are installed.


NOTICE:

Do not remove optional components without permission of the customer.




OK

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

NG

3.INSPECT WINDSHIELD GLASS ANTENNA WIRE
3.INSPECT WINDSHIELD GLASS ANTENNA WIRE
a.

Inspect the windshield glass antenna wire (See page Audio / Visual / Telematics>AUDIO / VIDEO>WINDOW GLASS ANTENNA WIRE>REPAIR).



OK

4.CHECK NAVIGATION RECEIVER ASSEMBLY

NG

4.CHECK NAVIGATION RECEIVER ASSEMBLY
a.

Remove the antenna connector from the navigation receiver assembly.


b.

Turn the engine switch on (ACC) with the navigation receiver assembly connector connected.


c.

Turn on the radio and turn into AM mode.


d.

Place a screwdriver, thin wire or other metal object on the navigation receiver assembly antenna jack and check that noise can be heard from the speakers.

OK:

Noise occurs.




OK

5.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 2 ANTENNA CORD SUB-ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 2 ANTENNA CORD SUB-ASSEMBLY)
a.

Disconnect the DB navigation receiver assembly connector.


b.

Disconnect the antenna connector from the No.2 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 1 Always Below 1 Ω
1-a - 1-a Always Below 1 Ω
1 - Body ground Always 10 kΩ or higher
1-a - Body ground Always 10 kΩ or higher




OK

6.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
E286153E05
1.792,1.063 2.083,0.667 2.083,0.667 2.333,0.667 true 1.781,2.552 2.083,2.167 2.083,2.167 2.333,2.167 true 0.146,0.365 0.458,0.563 0.313,0.198 10 false *a 0.188,1.917 0.5,2.115 0.313,0.198 10 false *b 2.417,2.063 2.729,2.26 0.313,0.198 10 false 1-a 2.396,0.573 2.708,0.771 0.313,0.198 10 false 1-a

Disconnect the antenna connector from the navigation receiver assembly.


b.

Disconnect the antenna connector from the digital audio broadcasting antenna assembly LH.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 1 Always Below 1 Ω
1-a - 1-a Always Below 1 Ω
1 - Body ground Always 10 kΩ or higher
1-a - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Digital Audio Broadcasting Antenna Assembly LH)
*b Front view of wire harness connector
(to Vehicle Wire Harness)



OK

7.CHECK DIGITAL AUDIO BROADCASTING ANTENNA ASSEMBLY LH

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

7.CHECK DIGITAL AUDIO BROADCASTING ANTENNA ASSEMBLY LH

OK

END (DIGITAL AUDIO BROADCASTING ANTENNA ASSEMBLY LH IS DEFECTIVE)

NG

8.CHECK DIGITAL AUDIO BROADCASTING ANTENNA ASSEMBLY RH
8.CHECK DIGITAL AUDIO BROADCASTING ANTENNA ASSEMBLY RH

OK

END (DIGITAL AUDIO BROADCASTING ANTENNA ASSEMBLY RH IS DEFECTIVE)

NG