Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/ Multi-display) › 2015.06–2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261009 TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/ Multi-display) J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/ Multi-display)  Main Switch Circuit  


DESCRIPTION

for 4 Sensor Type:

When the back sonar or clearance sonar switch assembly is turned on, the on signal is input into the ECU.

for 8 Sensor Type

When the driving support switch control ECU receives the clearance sonar on/off switch signal, the ECU sends it to the clearance warning ECU.

WIRING DIAGRAM

E285868E03
2.552,1.323 2.823,1.49 0.271,0.167 10 false IND 4.344,0.865 4.667,1.052 0.323,0.188 10 false ECU 2.552,0.875 2.875,1.063 0.323,0.188 10 false IG 4.76,0.625 4.927,0.813 0.167,0.188 10 false 3 5.76,0.76 6.219,0.948 0.458,0.188 10 false CSSW 0.177,0.75 1.167,1.146 0.99,0.396 10 false from IG1 NO.1 Relay 0.073,0.042 2.198,0.438 2.125,0.396 12 false for 4 Sensor Type: 1.344,0.906 2.281,1.094 0.938,0.188 10 false ECU-IG NO. 2 5.604,1.813 6.031,2 0.427,0.188 10 false I1 5.604,1.979 6.865,2.344 1.26,0.365 10 false Clearance Warning ECU 2.583,1.677 3.01,1.865 0.427,0.188 10 false G13 2.583,1.833 4.615,2.167 2.031,0.333 10 false Back Sonar or Clearance Sonar Switch Assembly 5.458,0.625 5.677,0.813 0.219,0.188 10 false 12 2.354,1.083 2.677,1.271 0.323,0.188 10 false 7 2.365,0.625 2.49,0.813 0.125,0.188 10 false 6

E283772E05
1.469,1.104 1.927,1.302 0.458,0.198 10 false SWO1 1.948,0.979 2.188,1.146 0.24,0.167 10 false 9*1 5.083,0.979 5.313,1.177 0.229,0.198 10 false 12 5.333,1.094 5.792,1.292 0.458,0.198 10 false CSSW 5.156,1.688 5.604,1.844 0.448,0.156 10 false G154 5.146,1.844 6.667,2.031 1.521,0.188 10 false Clearance Warning ECU 0.625,1.594 1.135,1.781 0.51,0.188 10 false G162*1 0.625,1.75 2.031,2.115 1.406,0.365 10 false Driving Support Switch Control ECU 0.146,0.063 1.563,0.333 1.417,0.271 12 false for 8 Sensor Type: 1.135,1.594 1.646,1.781 0.51,0.188 10 false G76*2 2.219,0.979 2.552,1.146 0.333,0.167 10 false 12*2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body / Clearance Sonar / Data List.


e.

According to the display on the GTS, read the Data List.

Clearance Sonar
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Main Switch TOYOTA parking assist-sensor system (multi-function switch)/OFF or ON OFF: TOYOTA parking assist-sensor system off
ON: TOYOTA parking assist-sensor system on
-

OK:

The display changes as shown above when the TOYOTA parking assist-sensor system is operated.


Result
Result Proceed to
OK A
NG (for 4 Sensor Type) B
NG (for 8 Sensor Type) C



A

B

2.INSPECT BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY

C

4.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT SWITCH CONTROL ECU - CLEARANCE WARNING ECU)
2.INSPECT BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY
a.

Remove the back sonar or clearance sonar switch assembly (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE SONAR MAIN SWITCH>REMOVAL).


b.

Inspect the back sonar or clearance sonar switch assembly (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE SONAR MAIN SWITCH>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY - CLEARANCE WARNING ECU, BATTERY AND BODY GROUND)

NG

REPLACE BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY - CLEARANCE WARNING ECU, BATTERY AND BODY GROUND)
a.

Disconnect the G13 back sonar or clearance sonar switch assembly connector.


b.

Disconnect the I1 clearance warning ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G13-6 (IG) - Body ground Engine switch on (IG) 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G13-3 (ECU) - I1-12 (CSSW) Always Below 1 Ω
G13-7 (IND) - Body ground Always Below 1 Ω
G13-3 (ECU) - Body ground Always 10 kΩ or higher


Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT SWITCH CONTROL ECU - CLEARANCE WARNING ECU)
a.

Disconnect the G162*1 or G76*2 driving support switch control ECU connector.

*1: for Automatic Transmission

*2: for Manual Transmission



b.

Disconnect the G154 clearance warning ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Automatic Transmission
Tester Connection Condition Specified Condition
G162-9 (SWO1) - G154-12 (CSSW) Always Below 1 Ω
G162-9 (SWO1) - Body ground Always 10 kΩ or higher

for Manual Transmission
Tester Connection Condition Specified Condition
G76-12 (SWO1) - G154-12 (CSSW) Always Below 1 Ω
G76-12 (SWO1) - Body ground Always 10 kΩ or higher




OK

5.CHECK DRIVING SUPPORT SWITCH CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK DRIVING SUPPORT SWITCH CONTROL ECU
a.

Replace the driving support switch control ECU with a new or normally functioning one (See page Steering>STEERING COLUMN>DRIVING SUPPORT SWITCH CONTROL ECU>REMOVAL).


b.

Check the TOYOTA parking assist-sensor system operates normally.

OK:

TOYOTA parking assist-sensor system operates normally.


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

END (DRIVING SUPPORT SWITCH CONTROL ECU IS DEFECTIVE)

B

C