Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › SIDE MONITOR SYSTEM › 2015.06–2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261013 SIDE MONITOR SYSTEM D

PARK ASSIST / MONITORING  SIDE MONITOR SYSTEM  CALIBRATION  


ADJUST SIDE MONITOR SYSTEM


a.

This side monitor system can be set from the diagnostic screen of the navigation receiver assembly*1 or radio and display receiver assembly*2.


b.

If the following operations are performed, it is necessary to perform adjustments and checks on the diagnostic screen.

Part Name Operation Adjustment Item Proceed to
Spiral cable sub-assembly
·

Removal and installation of the spiral cable sub-assembly

·

Removal and installation of the connector of the spiral cable sub-assembly

·

Replacement


Steering angle neutral point (Click here)
Steering angle setting (Click here)
Parking assist ECU Replacement Parking assist ECU initialization (Click here)
Suspension, tires, etc. The vehicle height changes because of suspension or tire replacement Rear television camera optical axis (Camera position setting) (Click here)
Side television camera optical axis (Camera position setting) Procedure 1
Side television camera assembly
·

Replacement

·

Installation angle of the side television camera changes because of the removal and installation of the side television camera, etc.


Side television camera optical axis (Camera position setting) Procedure 1
Outer rear view mirror assembly Replacement Side television camera optical axis (Camera position setting) Procedure 1

*1: for Navigation Receiver Type

*2: for Radio and Display Type


NOTICE:

After the engine switch is turned off, the navigation receiver assembly*1 or radio and display receiver assembly*2 records various types of memory and settings. As a result, after turning the engine switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal
Condition Waiting Time
Vehicle enrolled in G-BOOK system 6 minutes
Vehicle not enrolled in G-BOOK system 1 minute


HINT:

The adjustment values stored while performing side monitor system calibration are stored in the parking assist ECU.




SIDE CAMERA SETTING (Procedure 1)


HINT:

Be sure to check for DTCs before performing this procedure (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>SIDE MONITOR SYSTEM>DTC CHECK / CLEAR).


a.

Preparation for adjustment

i.

Park the vehicle with the steering wheel centered.


ii.
E181012E03
2.055,0.387 2.267,0.553 0.213,0.166 10 *a 2.261,0.963 2.473,1.129 0.213,0.166 10 *b 2.269,2.656 2.482,2.822 0.213,0.166 10 *c 1.951,3.876 2.164,4.042 0.213,0.166 10 *d 1.431,1.559 1.01,0.967 1.01,0.967 0.813,0.967 false 0.657,0.883 0.814,1.050 0.157,0.166 10 B 2.66,2.043 2.817,2.210 0.157,0.166 10 A

Set a target bar for optical axis adjustment of the rear television camera.

HINT:

Only when adjusting the optical axis of the camera, create a target bar for adjustment.


Dimension:
Area Specification
A 990 to 1000 mm (3.25 to 3.28 ft.)
B 1995 to 2005 mm (6.45 to 6.58 ft.)


Text in Illustration
*a Vehicle Center
*b Target Bar for Back Camera Adjustment
*c Vehicle End
*d Front Side

HINT:
·

Set a piece of tape on the ground as the target bar for adjustment. Its width and length are 20 to 30 mm (0.787 to 1.18 in.) and 1995 to 2005 mm (6.55 to 6.58 ft.), respectively. Check the color on the multi-display assembly and choose a tape color which can be easily seen.

·

Before parking the vehicle, be sure to move the vehicle forward and in reverse to check that the tires are facing straight ahead with the steering wheel centered.

·

Check that the back door is fully closed.




iii.

Set a target bar for optical axis adjustment of the side television camera.

HINT:

Only when adjusting the optical axis of the camera, create a target bar for adjustment.


1.

for LHD:

E180069E05
3.458,0.317 3.591,0.484 0.133,0.167 10 A 3.867,2.713 4.000,2.880 0.133,0.167 10 F 4.176,2.713 4.309,2.880 0.133,0.167 10 E 4.656,1.662 4.789,1.829 0.133,0.167 10 B 5.165,1.676 5.298,1.843 0.133,0.167 10 C 5.165,2.073 5.298,2.240 0.133,0.167 10 D 1.947,1.885 2.106,2.052 0.158,0.167 10 *c 4.509,1.092 4.668,1.260 0.158,0.167 10 *a 5.212,1.433 5.370,1.601 0.158,0.167 10 *b 2.942,3.321 3.100,3.489 0.158,0.167 10 *d 3.998,1.753 4.322,1.179 4.322,1.179 4.487,1.179 false

2.

for RHD:

E180068E02
3.661,0.324 3.794,0.491 0.133,0.167 10 A 3.261,2.72 3.394,2.887 0.133,0.167 10 F 2.954,2.72 3.087,2.887 0.133,0.167 10 E 2.519,1.676 2.652,1.843 0.133,0.167 10 B 1.915,1.704 2.047,1.872 0.133,0.167 10 C 1.91,2.087 2.043,2.254 0.133,0.167 10 D 5.18,1.86 5.339,2.028 0.158,0.167 10 *c 2.788,0.873 2.946,1.040 0.158,0.167 10 *a 1.884,1.433 2.043,1.601 0.158,0.167 10 *b 4.147,3.328 4.305,3.496 0.158,0.167 10 *d 3.215,1.711 2.965,0.942 false


Text in Illustration
*a Target Bar for Side Camera Adjustment *b Front Wheel Axis
*c Front Side *d Vehicle Center

Dimension:
A B C D E F
1183 mm
(3.88 ft.)
1181 mm
(3.87 ft.)
500 mm
(1.64 ft.)
500 mm
(1.64 ft.)
500 mm
(1.64 ft.)
180 mm
(7.09 in.)


HINT:

Target bars for side camera adjustment should be made with 2 pieces of 2.5 cm wide tape; one piece should be 100 cm (3.28 ft.) (C+D) and the other should be 68 cm (2.23 ft.) (E+F) long. Check the tape color on the multi-display assembly and choose a tape color which can be easily seen.




b.

Start diagnostic mode.


NOTICE:

Alignment must be performed with the engine running. For this reason, it is necessary to apply the parking brake, depress the brake pedal, and move the shift lever to P, and to exercise all other necessary caution to ensure that the vehicle does not begin moving unexpectedly.


HINT:

The displayed items may differ depending on vehicle specifications.


i.
E271944

Select "Function Check/Setting" on the "Service Menu" screen.


ii.
E271945

Select "Camera Setting" on the "Function Check/Setting I" screen.


iii.
E246954

Select "Side Camera Setting" on the "Mode Setting" screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.



iv.
E285877

Select "Next" on the "Signal Check" screen.

NOTICE:
·

When "CHK" (red) is displayed for any items on the "Signal Check" screen, selecting "Next" will not change the screen to the "Side Camera Position Setting" screen.

·

When "CHK" (red) is displayed for any items on the "Signal Check" screen, perform inspections using the "Signal Check" screen (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>SIDE MONITOR SYSTEM>DIAGNOSIS SYSTEM).



HINT:
·

When the outer mirrors are retracted, selecting "Next" will not change the screen to the "Side Camera Position Setting" screen.

·

If the screen does not change to the "Side Camera Position Setting" screen even though the outer mirrors are extended, perform the "MIRROR SW" check on the "Signal Check" screen (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>SIDE MONITOR SYSTEM>DIAGNOSIS SYSTEM).

·

If the screen does not change to the "Side Camera Position Setting" screen even after "OK" (blue) is displayed as a result of the MIRROR SW check on the "Signal Check" screen, replace the parking assist ECU (for LHD) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU (for LHD)>REMOVAL), (for RHD) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU (for RHD)>REMOVAL).





c.
E181004E02
1.357,0.396 1.556,0.546 0.199,0.149 10 *a 2.029,0.877 2.228,1.026 0.199,0.149 10 *b 1.722,1.676 1.921,1.825 0.199,0.149 10 *c 0.962,0.828 1.323,0.509 false 1.693,1.094 2.005,0.963 false 1.311,1.51 1.688,1.748 false

Side Camera Position Setting:

HINT:

Colors used on the "Side Camera Position Setting" screen


Text in Illustration
*a Target Adjustment Bar for Side Camera Position Setting
*b Red Frame
*c Yellow Frame

i.
E246955E06
0.188,0.573 0.292,0.573 0.292,0.573 0.552,0.719 false 0.917,2.052 1.021,2.052 1.021,2.052 1.125,1.854 false 1.271,2.052 1.375,2.052 1.375,2.052 1.49,1.854 false 1.708,2.052 1.813,2.052 1.813,2.052 1.927,1.854 false 2.177,2.052 2.281,2.052 2.281,2.052 2.396,1.854 false 0.188,1.208 1.396,1.208 false 3.281,0.573 3.177,0.573 3.177,0.573 2.927,0.719 false 0.042,0.479 0.167,0.656 0.125,0.177 10 false A 3.302,0.49 3.427,0.667 0.125,0.177 10 false B 0.771,1.958 0.896,2.135 0.125,0.177 10 false D 1.135,1.958 1.26,2.135 0.125,0.177 10 false E 1.552,1.958 1.677,2.135 0.125,0.177 10 false F 2.021,1.958 2.146,2.135 0.125,0.177 10 false G 0.042,1.125 0.167,1.302 0.125,0.177 10 false C

Perform the roll angle adjustment.

·

Select switches A and B to rotate C so that it is parallel to the target adjustment bar.



ii.

Perform the vertical and horizontal position adjustment.

·

Select the directional switches D, E, F and G to move C so that the target adjustment bar is centered in C.



iii.

Select "Next" to display "Side Verify Mode".



d.

Side Verify Mode:

i.
E246956

Check that the red cross and the target adjustment bar are aligned.

HINT:

If they are not aligned, select "Back" and perform "Side Camera Position Setting" again.



ii.

Select "Next" to display "Side Camera Signal Check".



e.

Side Camera Signal Check (w/ Multi-terrain Monitor):

i.
E346114

Select "OK" to store the side camera aiming adjustment value and change the screen to the "Service Menu" screen.

HINT:
·

When "OK" is selected, a beep will sound to confirm that the side camera aiming adjustment values have been stored.

·

The adjustment value will not be stored unless "Back" is selected.