The video signal from the rear television camera assembly is transmitted to the navigation receiver assembly*1 or radio and display receiver assembly*2.
*1: for Navigation Receiver Type
*2: for Radio and Display Type
If the cable was disconnected from and reconnected to the negative (-) battery terminal, the estimated course lines may not be displayed on the image of the area behind the vehicle. In this case, perform "Correct the Steering Angle Neutral Point" (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM (for Camera built-in ECU)>INITIALIZATION).
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM (for Camera built-in ECU)>CALIBRATION).
Check the vehicle type.
| Result | Proceed to |
|---|---|
| for Navigation Receiver Type | A |
| for Radio and Display Type | B |
A
B
Disconnect the v3*1 or X10*2 rear television camera assembly connector.
*1: w/ Tire Carrier
*2: w/o Tire Carrier
Disconnect the H55 navigation receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| v3-6 (CB+) - H55-11 (CA+) | Always | Below 1 Ω |
| v3-3 (CV+) - H55-12 (V+) | Always | Below 1 Ω |
| v3-2 (CV-) - H55-24 (V-) | Always | Below 1 Ω |
| v3-5 (CGND) - H55-23 (CGND) | Always | Below 1 Ω |
| v3-6 (CB+) or H55-11 (CA+) - Body ground | Always | 10 kΩ or higher |
| v3-3 (CV+) or H55-12 (V+) - Body ground | Always | 10 kΩ or higher |
| v3-2 (CV-) or H55-24 (V-) - Body ground | Always | 10 kΩ or higher |
| v3-5 (CGND) or H55-23 (CGND) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| X10-6 (CB+) - H55-11 (CA+) | Always | Below 1 Ω |
| X10-3 (CV+) - H55-12 (V+) | Always | Below 1 Ω |
| X10-2 (CV-) - H55-24 (V-) | Always | Below 1 Ω |
| X10-5 (CGND) - H55-23 (CGND) | Always | Below 1 Ω |
| X10-6 (CB+) or H55-11 (CA+) - Body ground | Always | 10 kΩ or higher |
| X10-3 (CV+) or H55-12 (V+) - Body ground | Always | 10 kΩ or higher |
| X10-2 (CV-) or H55-24 (V-) - Body ground | Always | 10 kΩ or higher |
| X10-5 (CGND) or H55-23 (CGND) - Body ground | Always | Below 1 Ω |
OK
NG
Remove the navigation receiver assembly with the connector still connected (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION RECEIVER>REMOVAL).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| H55-11 (CA+) - H55-23 (CGND) | Engine switch on (ACC) | 5.5 to 7.05 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H55-23 (CGND) - Body ground | Always | Below 1 Ω |
| *a | Component with harness connected
(Navigation Receiver Assembly) |
OK
NG
| *a | Component with harness connected
(Navigation Receiver Assembly) |
*b | Waveform 1 |
| *c | Waveform 2 | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
Remove the navigation receiver assembly with the connector still connected (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION RECEIVER>REMOVAL).
Check the waveform of the rear television camera assembly using an oscilloscope.
A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.
| Item | Content |
|---|---|
| Measurement terminal | H55-12 (V+) - H55-24 (V-) |
| Measurement setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Waveform 1: Engine starts, shift lever in R, camera lens is not covered, displaying an image.
Waveform 2: Engine starts, shift lever in R, camera lens is covered, blacking out the screen. |
The video waveform changes according to the image sent by the rear television camera assembly.
The video waveform is constantly output when the engine switch is on (ACC).
Waveform is as shown in the illustration.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/ Tire Carrier) | B |
| NG (w/o Tire Carrier) | C |
A
B
C
Disconnect the v3*1 or X10*2 rear television camera assembly connector.
*1: w/ Tire Carrier
*2: w/o Tire Carrier
Disconnect the H50 radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| v3-6 (CB+) - H50-11 (CA+) | Always | Below 1 Ω |
| v3-3 (CV+) - H50-12 (V+) | Always | Below 1 Ω |
| v3-2 (CV-) - H50-24 (V-) | Always | Below 1 Ω |
| v3-5 (CGND) - H50-23 (CGND) | Always | Below 1 Ω |
| v3-6 (CB+) or H50-11 (CA+) - Body ground | Always | 10 kΩ or higher |
| v3-3 (CV+) or H50-12 (V+) - Body ground | Always | 10 kΩ or higher |
| v3-2 (CV-) or H50-24 (V-) - Body ground | Always | 10 kΩ or higher |
| v3-5 (CGND) or H50-23 (CGND) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| X10-6 (CB+) - H50-11 (CA+) | Always | Below 1 Ω |
| X10-3 (CV+) - H50-12 (V+) | Always | Below 1 Ω |
| X10-2 (CV-) - H50-24 (V-) | Always | Below 1 Ω |
| X10-5 (CGND) - H50-23 (CGND) | Always | Below 1 Ω |
| X10-6 (CB+) or H50-11 (CA+) - Body ground | Always | 10 kΩ or higher |
| X10-3 (CV+) or H50-12 (V+) - Body ground | Always | 10 kΩ or higher |
| X10-2 (CV-) or H50-24 (V-) - Body ground | Always | 10 kΩ or higher |
| X10-5 (CGND) or H50-23 (CGND) - Body ground | Always | Below 1 Ω |
OK
NG
Remove the radio and display receiver assembly with the connector still connected (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| H50-11 (CA+) - H50-23 (CGND) | Engine switch on (ACC) | 5.5 to 7.05 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H50-23 (CGND) - Body ground | Always | Below 1 Ω |
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
OK
NG
(See pageAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL)
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
*b | Waveform 1 |
| *c | Waveform 2 | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
Remove the radio and display receiver assembly with the connector still connected (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL).
Check the waveform of the rear television camera assembly using an oscilloscope.
A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.
| Item | Content |
|---|---|
| Measurement terminal | H50-12 (V+) - H50-24 (V-) |
| Measurement setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Waveform 1: Engine starts, shift lever in R, camera lens is not covered, displaying an image.
Waveform 2: Engine starts, shift lever in R, camera lens is covered, blacking out the screen. |
The video waveform changes according to the image sent by the rear television camera assembly.
The video waveform is constantly output when the engine switch is on (ACC).
Waveform is as shown in the illustration.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/ Tire Carrier) | B |
| NG (w/o Tire Carrier) | C |
A
(See pageAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL)
B
C